Difference between revisions of "Transtape"

From CPCWiki - THE Amstrad CPC encyclopedia!
Jump to: navigation, search
(→‎Technical)
(→‎Technical)
Line 7: Line 7:
 
* Uses a 16KB ROM paged into memory at &0000.
 
* Uses a 16KB ROM paged into memory at &0000.
 
* Uses a 8KB static RAM paged into memory at &c000-&dfff and repeats again at &e000-&ffff.
 
* Uses a 8KB static RAM paged into memory at &c000-&dfff and repeats again at &e000-&ffff.
−
* ROM is paged into the range &0000-&3fff when the red button is pressed and the NMI vector is executed.
+
* ROM is paged into the range &0000-&3fff when the red button is pressed (this causes an NMI).
−
* When the black button is pressed, the ROM is paged into the range &0000-&3fff and executes it at &0000.
+
* When the black button is pressed the ROM is paged into the range &0000-&3fff and executes it at &0000. (this is a reset)
−
* This checks the BASIC ROM version, and clears the extra ram if a BASIC ROM from a CPC6128 is found.
+
This checks the BASIC ROM version, and clears the extra ram if a BASIC ROM from a CPC6128 is found.
−
 
+
−
Code:
+
−
 
+
−
0000 f3        di                              ;; disable maskable interrupts
+
−
0001 0100df    ld      bc,0df00h ;; select upper rom 0
+
−
0004 ed49      out    (c),c
+
−
0006 01817f    ld      bc,7f81h ;; enable upper rom (mode 1 too)
+
−
0009 ed49      out    (c),c
+
−
000b 31febf    ld      sp,0bffeh                ;; setup stack which is not initialised after reset
+
−
+
−
000e 3a02c0    ld      a,(0c002h)              ;; read BASIC ROM version number
+
−
0011 fe02      cp      02h                      ;; CPC6128?
+
−
0013 cc2e0c    call    z,0c2eh         ;; erase extra RAM
+
−
+
−
;; this appears to set it up for a reset..
+
−
0016 210000    ld      hl,0000h
+
−
0019 e5        push    hl
+
−
001a e5        push    hl
+
−
001b c30038    jp      3800h                    ;; I think the hardware monitors for address 3800h and if found disables the ROM
+
−
 
+
 
* Uses NMI
 
* Uses NMI
−
* Doesn't capture the hardware state like the Multiface does. Code in the ROM reads the hardware state which it restores when resuming the program.
+
* Only captures upper/lower ROM enabled state and nothing else. Doesn't capture the hardware state like the Multiface does. Code in the ROM reads the hardware state which it restores when resuming the program.
−
* RAMDIS is asserted when ROM or RAM are active meaning no write through to ram behind.
+
* RAMDIS is asserted when ROM or RAM are active meaning no write through to ram behind. This also means that c000-ffff reads unmapped ram when ram is not actually enabled.
 
* Menu code is at offset &3810 and is copied into RAM at &A200.  
 
* Menu code is at offset &3810 and is copied into RAM at &A200.  
 +
* ram is disabled when the transtape returns to the program and can only be enabled using i/o port.
 
* Uses port FBF0 (write only)
 
* Uses port FBF0 (write only)
 
  FBF0 decoding is:
 
  FBF0 decoding is:

Revision as of 16:37, 6 November 2015

A Spanish Hacking Device from HM (Hard Micro, S.A.).

Transtape

Technical

  • Uses a 16KB ROM paged into memory at &0000.
  • Uses a 8KB static RAM paged into memory at &c000-&dfff and repeats again at &e000-&ffff.
  • ROM is paged into the range &0000-&3fff when the red button is pressed (this causes an NMI).
  • When the black button is pressed the ROM is paged into the range &0000-&3fff and executes it at &0000. (this is a reset)

This checks the BASIC ROM version, and clears the extra ram if a BASIC ROM from a CPC6128 is found.

  • Uses NMI
  • Only captures upper/lower ROM enabled state and nothing else. Doesn't capture the hardware state like the Multiface does. Code in the ROM reads the hardware state which it restores when resuming the program.
  • RAMDIS is asserted when ROM or RAM are active meaning no write through to ram behind. This also means that c000-ffff reads unmapped ram when ram is not actually enabled.
  • Menu code is at offset &3810 and is copied into RAM at &A200.
  • ram is disabled when the transtape returns to the program and can only be enabled using i/o port.
  • Uses port FBF0 (write only)
FBF0 decoding is:
1111 1011 1111 00xx

FBF0 output:
bit 0 is ram enable/disable state
bit 1 is rom enable/disable state
bit 2 is A10 on RAM
bit 3 is A11 on RAM
bit 4 is A12 on RAM
bits 5-7 are not used.
  • an opcode read of an address with the following bits:

0011 1xxx xxxx xxxx causes the ram and rom to be disabled. (it jumps to 3800 in the ROM to restore the state)

  • Uses port FBFF (input). 
bit 7 is used to report lower rom and upper rom enabled state.

Transtape ROM performs a read of 3ffe (lower rom) and fffe (upper rom) and records the state of ROMEN.

Decoding of FBFF is: 

1111 1011 1111 11xx


  • The same plastic case is used by the Spectrum version of this interface.
  • The spectrum version has two switches on the top. One of which chooses load/save. In the Amstrad these holes are filled with plastic caps.

Pictures

  • Transtape

  • Front

  • Back

  • PCB Top

  • PCB Bottom

  • Transtape Layout, thanks to Jose Leandro

  • Transtape - PCB Front

  • Transtape - PCB Back

  • Transtape - Layout

Manual

Downloads

Links

Retrieved from "https://gryzor.info/index.php?title=Transtape&oldid=94563"