Difference between revisions of "Vortex Winchester Drive"

From CPCWiki - THE Amstrad CPC encyclopedia!
Jump to: navigation, search
(→‎Technical)
 
(16 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
A HardDiscDrive (HDD) solution for the CPC.
+
A Harddisk (HDD) solution for the CPC. The first for the CPC.
 +
Produced  by the German company [[Vortex]]
  
−
Actually the first for the CPC.
+
The Harddisk was build about 1986. It has the same cases like the F1-S and the F1-D.  
  
−
Produced  by the German company [[Vortex]]
+
A big Power Supply which have about 1,5 Kilograms gives the power to the Harddrive.
  
 +
It was shipped with the power supply, the harddisk itself, a built in 5,25" DD Diskdrive with 720KB and a controller.
  
−
The Harddisc was build about 1986. It have the same cases like the F1-S and the F1-D. A big Power Supply which have about 1,5 Kilograms gives the power to the Harddrive. The Harddrive was shipped with the Powersupply The Harddrive itself, a built in 5,25" DD Diskdrive with 720KB and a Controller which was used for being the MFM Controller with two ports for two MFM Harddiscs, two DD Floppys and a ROM board which give place for 2 Roms, which held the VDOS 2.0
+
The controller has two ports for two MFM Harddiscs (with 60MB capacity), two DD Floppys and a ROM board which give place for 2 Roms, which held the VDOS 2.0.
−
The Contoller get the Power from the Harddisc.
+
 
−
You can connect up to two 60MB MFM Drives which are supported by the VDOS 2.0.
+
The VDOS used is specially adapted to support the hard disk.
−
But the normal setup was with a 20 MB MFM Drive.
+
 
 +
The Contoller get it's power from the Harddisc.
 +
 
 +
The normal setup had a single 20 MB MFM Drive.
  
 
A Software Package consists of a few helpful tools:  
 
A Software Package consists of a few helpful tools:  
−
*LowLevel Format
+
*Low level Format
 
*Partition tools
 
*Partition tools
 
*Format partitions
 
*Format partitions
 
*Patch for CPM 2.2 and 3.0 (Plus) to support the Drive
 
*Patch for CPM 2.2 and 3.0 (Plus) to support the Drive
 
*File/Disccopy Tools
 
*File/Disccopy Tools
−
*Diskformat
+
*Disk format
−
*Hexeditor
+
*Hex editor
 
*and a few more...
 
*and a few more...
  
 
== Technical ==
 
== Technical ==
  
−
CPCAI magazine claims the device has a WD1010 Winchester controller inside.
+
CPCAI magazine claims the device has a WD1010 Winchester controller inside. It certainly seems to be WD1010 compatible.
 +
 
 +
The WD1010 has different commands and communication method compared to the Dobbertin (which appears to use SASI) and modern IDE (which uses ATA). It looks to be an ancester of the IDE because of the seperate cylinder and sector registers and a single command write to initiate commands but it's not the same as IDE/ATA.
 +
 
 +
Therefore the software & hardware is *not* compatible with other interfaces.
 +
 
 +
Port decoding appears to be:
 +
bit 9 = wd1010 a2
 +
bit 1 = wd1010 a1
 +
bit 0 = wd1010 a0
 +
 
 +
bit 10 = 0
 +
bit 2 = 0
 +
 
 +
Except for bit 8, other bits are 1. It is not known which bits are decoded by the interface.
 +
 
 +
Bit 8 is 1 or 0, maybe it can't be either, but if it is set it could clash
 +
with other i/o. Maybe the  ports chosen here don't clash.
 +
 
 +
Ports used and their function:
 +
 
 +
FBFA - wd1010 head/select (SDH) register (read/write)
 +
FBFB - wd1010 write command (write)/wd1010 read status register (read)
 +
F9F8 - WD1010 data register (read/write)
 +
F9F9 = wd1010 precompensation register (write)
 +
F9FA = wd1010 sector count register (read/write)
 +
F9FB = wd1010 sector number register (read/write)
 +
FAF8 = wd1010 cylinder low register (read/write)
 +
FAF9 = wd1010 cylinder high register (read/write)
 +
FAFA = drive/head select? drive bits match those in sdh. (write)
 +
 
 +
wd1010 documentation says head select/drive select not available as outputs.
 +
 
 +
"Description" sector:
 +
(incomplete)
 +
 
 +
byte 0: checksum of bytes 1 to 255 in sector
 +
byte 7: ? not 0x0fe
 +
byte 240: !=0 => no password, 0 => password
 +
byte 241: password length in characters
 +
byte 242: password characters CPLed (up to 10 characters?)
 +
byte 252: drive id (0=a, 1=b, 2=c etc)
 +
 +
Furthur details:
 +
* MFM 
 +
* 256 bytes per sector.
 +
* 32 sectors per cylinder
 +
* AMSDOS & CPM based filesystem
 +
* ROM doesn't autodetect hard disk. It asks you if it is connected and if you answer yes it accesses the drive. It can hang if no drive is connected.
  
 
== Links ==
 
== Links ==
 +
  
 
* http://www.tiffe.de/Robotron/Winchester-HD/Western_Digital/WD1010.pdf
 
* http://www.tiffe.de/Robotron/Winchester-HD/Western_Digital/WD1010.pdf
  
 
  [[Category:Peripherals]][[Category:DATA Storage]]
 
  [[Category:Peripherals]][[Category:DATA Storage]]

Latest revision as of 08:19, 6 September 2015

A Harddisk (HDD) solution for the CPC. The first for the CPC. Produced by the German company Vortex

The Harddisk was build about 1986. It has the same cases like the F1-S and the F1-D.

A big Power Supply which have about 1,5 Kilograms gives the power to the Harddrive.

It was shipped with the power supply, the harddisk itself, a built in 5,25" DD Diskdrive with 720KB and a controller.

The controller has two ports for two MFM Harddiscs (with 60MB capacity), two DD Floppys and a ROM board which give place for 2 Roms, which held the VDOS 2.0.

The VDOS used is specially adapted to support the hard disk.

The Contoller get it's power from the Harddisc.

The normal setup had a single 20 MB MFM Drive.

A Software Package consists of a few helpful tools:

  • Low level Format
  • Partition tools
  • Format partitions
  • Patch for CPM 2.2 and 3.0 (Plus) to support the Drive
  • File/Disccopy Tools
  • Disk format
  • Hex editor
  • and a few more...

Technical

CPCAI magazine claims the device has a WD1010 Winchester controller inside. It certainly seems to be WD1010 compatible.

The WD1010 has different commands and communication method compared to the Dobbertin (which appears to use SASI) and modern IDE (which uses ATA). It looks to be an ancester of the IDE because of the seperate cylinder and sector registers and a single command write to initiate commands but it's not the same as IDE/ATA.

Therefore the software & hardware is *not* compatible with other interfaces.

Port decoding appears to be: 

bit 9 = wd1010 a2
bit 1 = wd1010 a1
bit 0 = wd1010 a0

bit 10 = 0 
bit 2 = 0

Except for bit 8, other bits are 1. It is not known which bits are decoded by the interface.

Bit 8 is 1 or 0, maybe it can't be either, but if it is set it could clash with other i/o. Maybe the ports chosen here don't clash.

Ports used and their function: 

FBFA - wd1010 head/select (SDH) register (read/write)
FBFB - wd1010 write command (write)/wd1010 read status register (read) 
F9F8 - WD1010 data register (read/write) 
F9F9 = wd1010 precompensation register (write)
F9FA = wd1010 sector count register (read/write)
F9FB = wd1010 sector number register (read/write)
FAF8 = wd1010 cylinder low register (read/write)
FAF9 = wd1010 cylinder high register (read/write)
FAFA = drive/head select? drive bits match those in sdh. (write)

wd1010 documentation says head select/drive select not available as outputs.

"Description" sector: (incomplete) 

byte 0: checksum of bytes 1 to 255 in sector
byte 7: ? not 0x0fe
byte 240: !=0 => no password, 0 => password
byte 241: password length in characters
byte 242: password characters CPLed (up to 10 characters?)
byte 252: drive id (0=a, 1=b, 2=c etc)

Furthur details:

  • MFM
  • 256 bytes per sector.
  • 32 sectors per cylinder
  • AMSDOS & CPM based filesystem
  • ROM doesn't autodetect hard disk. It asks you if it is connected and if you answer yes it accesses the drive. It can hang if no drive is connected.

Links

Retrieved from "https://gryzor.info/index.php?title=Vortex_Winchester_Drive&oldid=94149"