Difference between revisions of "Gate Array"

From CPCWiki - THE Amstrad CPC encyclopedia!
Jump to: navigation, search
m (Rollback as undo swallowed all Prettytables & fixed table "Select pen" bit 4=0)
(→‎Interrupt generation)
 
(282 intermediate revisions by 11 users not shown)
Line 1: Line 1:
−
Gate Array
+
Gate Array  
  
−
== Introduction ==
+
Also designated as Video gate Array (VGA, not to be confused with IBM PC compatible graphic card spec).
  
−
The gate array is a specially designed chip exclusively for use in the Amstrad CPC and was designed by Amstrad plc.
+
<br>
  
−
In the CPC+ system, the functions of the Gate-Array are integrated into a single [[ASIC]]. When the ASIC is "locked", the extra features are not available and the ASIC operates the same as the Gate-Array in the CPC allowing programs written for the CPC to work on the Plus without modification. The ASIC must be "un-locked" to access the new features.
+
== Introduction  ==
  
−
In the [[KC Compact Computer|KC compact]] system, the functions of the Gate-Array are "emulated" in [[TTL logic]] and by the [[Zilog Z8536 CIO]].
+
The Gate Array is a specially designed chip exclusively for use in the Amstrad CPC and was designed by Amstrad plc.  
  
−
In the "cost-down" version of the CPC6128, the functions of the Gate-Array are integrated into a ASIC.
+
In the CPC+ system, the functions of the Gate Array are integrated into a single [[ASIC|ASIC]]. When the ASIC is "locked", the extra features are not available and the ASIC operates the same as the Gate Array in the CPC allowing programs written for the CPC to work on the Plus without modification. The ASIC must be "un-locked" to access the new features.  
  
−
The Gate Array is described here, as it is in a standard CPC.
+
In the [[KC Compact]] system, the functions of the Gate Array are "emulated" in TTL chips, [[CIO Overview|CIO]], and its color translation EPROM.
  
−
''What does it do?''
+
In the "cost-down" version of the CPC6128, the functions of the Gate Array are integrated into a ASIC.
  
−
The Gate Array is responsible for the display (colour palette, resolution, horizontal and vertical sync), interrupt generation and memory arrangement.
+
<br>
  
−
== Controlling the Gate Array ==
+
== What does it do? ==
  
−
The gate array is controlled by I/O. The gate array is selected when bit 15 of the I/O port address is set to "0" and bit 14 of the I/O port address is set to "1". The values of the other bits are ignored. However, to avoid conflict with other devices in the system, these bits should be set to "1".
+
The Gate Array is responsible for the display (colour palette, resolution, horizontal and vertical sync), bus arbitration, DRAM refresh, interrupt generation and memory arrangement.  
  
−
The recommended I/O port address is &7Fxx.
+
<br>
  
−
The function to be performed is selected by writing data to the Gate-Array, bit 7 and 6 of the data define the function selected (see table below). It is not possible to read from the Gate-Array.
+
== Bus arbitration ==
  
−
{|{{Prettytable|width: 700px; font-size: 2em;}}
+
The Gate Array arbitrates access to the RAM between the CPU and the video hardware (CRTC and Gate-Array).
−
|''Bit 7''||''Bit 6''||''Function''
+
−
|-
+
−
|0||0||Select pen
+
−
|-
+
−
|0||1||Select colour for selected pen
+
−
|-
+
−
|1||0||Select screen mode, rom configuration and interrupt control
+
−
|-
+
−
|1||1||Ram Memory Management (note 1)
+
−
|-
+
−
|}
+
  
−
===== Note =====
+
Every microsecond:
 +
* The CRTC generates a memory address using it's MA and RA signal outputs. See the [[CRTC]] wiki page to know how the motherboard wiring transforms these signals into the Video Memory Address (VMA).
 +
* The Gate Array fetches 2 bytes for each address. /CPU_ADDR is a 1MHz signal. So these 2 bytes are fetched sequentially. They are not interleaved with Z80 access. These bytes are fetched even when the border is on as this is required for DRAM refresh.
 +
* The video hardware is given priority so that the display is not disrupted.
  
−
This function is not available in the Gate-Array, but is performed by a device at the same I/O port address location. In the CPC464,CPC664 and KC compact, this function is performed in a memory-expansion (e.g. Dk'Tronics 64K Ram Expansion), if this expansion is not present then the function is not available. In the CPC6128, this function is performed by a PAL located on the main PCB, or a memory-expansion. In the 464+ and 6128+ this function is performed by the ASIC or a memory expansion. Please read the document on Ram Management for more information.  
+
The Gate-Array generates the "READY" signal which is connected to the "/WAIT" input signal of the CPU. This signal is used to stop the CPU accessing RAM while the video-hardware is accessing it.
  
−
==== Pen selection ====
+
In fact, the Gate Array allows the Z80 to access the RAM in only 1 out of every 4 cycles. As a result, all instruction timings are stretched so that they are all multiples of a microsecond (1µs), and this gives an effective CPU clock of 3.3Mhz.
  
−
When bit 7 and bit 6 are set to "0", the remaining bits determine which pen is to have its colour changed. When bit 4 is set to "0", bits 3 to 0 define which pen is to be selected. When bit 4 is set to "1", the value contained in bits 3-0 is ignored and the border is selected.
+
Unlike the ZX Spectrum or the Amiga, where bus arbitration is restricted to the "contended memory" or "chip RAM", on the CPC it also applies to ROM access and to RAM expansions. So the Z80 always runs at the same speed, regardless of the type of memory being accessed.
  
−
The pen remains selected until another is chosen.
+
Last but not least, bus arbitration also applies to I/O access. And memory access is not aligned with I/O access on Z80.
  
−
Each mode has a fixed number of pens. Mode 0 has 16 pens, mode 1 has 4 pens and mode 2 has 2 pens.
+
Note: On Amstrad Plus, the ASIC also has to handle DMA instruction fetch from RAM.
  
−
===== Summary =====
+
<br>
  
 +
== DRAM refresh ==
  
−
{|{{Prettytable|width: 700px; font-size: 2em;}}
+
On Amstrad CPC, the Gate Array is responsible for the DRAM refresh, instead of using the Z80 built-in DRAM refresh mechanism. The reason is that there can only be 3 DRAM accesses per microsecond on this architecture. Doing DRAM refresh on each M1 cycle as it is done on MSX would bog down the CPU speed on CPC given its bus arbitration scheme.
−
|''Bit''||''Value''||''Function''
+
 
−
|-
+
The Z80 generates a maximum of one request per microsecond. The CPC also requires two memory accesses per microsecond for reading video data.
−
|7||0||rowspan=2|Gate Array function "Pen Selection"
+
 
−
|-
+
The CPC specs 4164-20 DRAMs. These require 330nS for a read or write cycle. The CPC also uses the optimised sequential CAS cycles to read the two video data bytes in half a microsecond. [https://www.cpcwiki.eu/forum/amstrad-cpc-hardware/the-cpc-revision-zero-article/msg243769/ Source]
−
|6||0
+
 
−
|-
+
The way to cause the RAM refresh to fail in both a Plus or normal CPC is simply to stop a few bits of the CRTC address changing (ie. never refresh the selected area).
−
|5||-||not used
+
 
−
|-
+
Generally, only the Row address needs to be cycled, so stopping MA0 through MA7 from changing, and stopping the CPU from reading those rows, will cause data to be lost, quite quickly (generally around 4ms). [https://www.cpcwiki.eu/forum/amstrad-cpc-hardware/memory-refresh-plus/ Source]
−
|4||1||Select border
+
 
−
|-
+
<br>
−
|3||x||rowspan=4|Ignored
+
 
−
|-
+
== Interrupt generation ==
−
|2||x
+
 
−
|-
+
Interrupts on the CPC are created by the Gate Array based on settings from the CRTC. The Gate Array has an internal counter R52 (the R is for Raster) that counts from 0 to 51, incrementing after each HSYNC signal.
−
|1||x
+
 
−
|-
+
On all CRTCs, R52 interrupts always start 1µs after the end of an HSYNC. But on CRTCs 3/4, HSYNCs occur 1µs later than on CRTCs 0/1/2. Which means that on CRTCs 3/4, interrupts start 1µs later than on CRTCs 0/1/2. This can be adjusted by using the CRTC register 3.
−
|0||x
+
 
−
|-
+
R52 will return to 0 and the Gate Array will send an interrupt request on any of these conditions:
−
|}
+
* When it exceeds 51
 +
* By setting bit4 of the RMR register of the Gate Array to 1
 +
* At the end of the 2nd HSYNC after the start of the VSYNC
 +
 
 +
When the Gate Array sends an interrupt request:
 +
*If the interrupts were authorized at the time of the request, then bit5 of R52 is cleared (but R52 was reset to 0 anyway) and the interrupt takes place
 +
*If interrupts are not authorized, then the R52 counter continues to increment and the interrupt remains armed (the Gate Array then maintains its INT signal). When interrupts are enabled (using the EI instruction), bit5 of R52 is cleared and the interrupt takes place. This happens only '''after the instruction that follows EI''' as this Z80 instruction has a 1-instruction delay.
 +
 
 +
Note: On Amstrad Plus, the interrupt management system is seriously beefed up. See the [[ASIC]] wiki page.
 +
 
 +
<br>
 +
 
 +
== CSYNC signal ==
 +
 
 +
The HSYNC and VSYNC signals are received from the [[CRTC]]. These signals are then modified by the Gate Array to C-HSYNC and C-VSYNC and merged into a single CSYNC signal that will be sent to the display.
 +
 
 +
When CRTC HSYNC is active, the Gate Array immediately outputs the palette colour black. If the HSYNC is set to 14 characters then black will be output for 14µs.
 +
 
 +
If a graphics mode change is pending, the HSYNC pulse width needs to be at least 2µs for Gate Array to change the graphics mode.
 +
 
 +
C-HSYNC begins 2µs after activation of the CRTC HSYNC and stays a maximum of 4µs (signal is cut short if HSYNC width is greater than 6).
 +
 
 +
For example, if CRTC R2=46, and CRTC HSYNC width is 14 chars then C-HSYNC starts at 48 and lasts only until 51 included.
 +
 
 +
On Gate Array, even if the duration of the CRTC VSYNC is reduced to 2 µseconds, the Gate Array will always output black for 26 lines with 4 lines of C-VSYNC to the monitor. While on ASIC/Pre-ASIC, the CRTC VSYNC must be active as long as the C-VSYNC signal is sent to the monitor.
 +
 
 +
The Gate Array (and ASIC/Pre-ASIC) uses 2 internal counters to create its CSYNC signal:
 +
* H06 counts the number of CRTC characters processed during an HSYNC. H06 is incremented by the Gate Array for each CRTC character when CRTC HSYNC is active. The Gate Array activates the C-HSYNC signal when H06 reaches 2, and changes its graphics mode if a change was pending. It deactivates this signal when H06 reaches 6.
 +
* V26 counts the number of HSYNCs occuring during a VSYNC. V26 is incremented by the Gate Array when the CRTC signals an end of HSYNC. The Gate Array activates the C-VSYNC signal when V26 reaches 2 (and if VSYNC is active on ASIC/Pre-ASIC). It deactivates this signal when V26 reaches 6. After the 26th line has been processed, the Gate Array stops outputting the palette colour black.
 +
 
 +
If CRTC VSYNC is activated again while V26 is still in progress, then V26 is reset to 0 and starts counting up again the HSYNC pulses.
 +
 
 +
The HSYNC signal from the CRTC is 0 when inactive and 1 when active. Same for VSYNC.
 +
 
 +
C-HSYNC and C-VSYNC are composited using the XNOR function. The resulting CSYNC signal produced by the Gate Array is 1 when inactive and 0 when active.
 +
 
 +
On a CPC monitor, the CSYNC is rendered in "absolute black". It is darker than the palette colour black output by the Gate Array. The electron beam is basically turned off. Turning up the brightness level won't make it any brighter.
 +
 
 +
<br>
 +
 
 +
== Controlling the Gate Array  ==
 +
 
 +
The gate array is controlled by I/O. The gate array is selected when bit 15 of the I/O port address is set to "0" and bit 14 of the I/O port address is set to "1". The values of the other bits are ignored. However, to avoid conflict with other devices in the system, these bits should be set to "1".
 +
 
 +
The recommended I/O port address is &7Fxx.
  
 +
The function to be performed is selected by writing data to the Gate Array, the first bits of the data define the function selected (see table below). It is not possible to read from the Gate Array.
  
−
{|{{Prettytable|width: 700px; font-size: 2em;}}
+
{| class="wikitable"
−
|''Bit''||''Value''||''Function''
+
!colspan=4| 8bit command
 +
!rowspan=2| Machine
 +
!rowspan=2| Register
 +
!rowspan=2| Description
 +
!rowspan=2| Chip
 
|-
 
|-
−
|7||0||rowspan=2|Gate Array function "Pen Selection"
+
! 7
 +
! 6
 +
! 5
 +
! 4..0
 
|-
 
|-
−
|6||0
+
| 0 || 0 || x || style="text-align: center;" | n || All || PENR || Select a color register || Gate Array
 
|-
 
|-
−
|5||-||not used
+
| 0 || 1 || x || style="text-align: center;" | n || All || INKR || Change the value of the currently selected color register || Gate Array
 
|-
 
|-
−
|4||0||Select pen
+
| 1 || 0 || 0 || style="text-align: center;" | n || All || RMR || Control Interrupt counter, ROM mapping and Graphics mode || Gate Array
 
|-
 
|-
−
|3||x||rowspan=4|Pen number
+
| 1 || 0 || 1 || style="text-align: center;" | n || All || RMR || ''Ghost register'' || Gate Array (CPC) or locked ASIC (Plus)
 
|-
 
|-
−
|2||x
+
| 1 || 0 || 1 || style="text-align: center;" | n || Plus || RMR2 || ASIC & Advanced ROM mapping || Unlocked ASIC
−
|-
+
−
|1||x
+
−
|-
+
−
|0||x
+
 
|-
 
|-
 +
| 1 || 1 ||colspan=2  style="text-align: center;" | n || All || MMR || RAM memory mapping || PAL (only with 128KB or RAM expansion)
 
|}
 
|}
  
−
==== Colour selection ====
+
The MMR register is not available in the Gate Array, but is performed by a device at the same I/O port address location.
  
−
Once the pen has been selected the colour can then be changed. Bits 4 to 0 specify the hardware colour number from the hardware colour palette.
+
In the CPC464, CPC664 and KC compact, MMR is performed in an external memory expansion (e.g. Dk'Tronics 64K RAM Expansion), if this expansion is not present then MMR is not available.
  
−
Even though there is provision for 32 colours, only 27 are possible. The remaining colours are duplicates of those already in the colour palette.
+
In the CPC6128, MMR is performed by a [[PAL16L8|PAL]] located on the main PCB, or an external memory expansion.
  
−
===== Summary =====
+
In the 464+ and 6128+, MMR is performed by the ASIC or an external memory expansion. Please read the document on RAM management for more information.
  
−
{|{{Prettytable|width: 700px; font-size: 2em;}}
+
<br>
−
|''Bit''||''Value''||''Function''
+
 
 +
== Registers ==
 +
 
 +
Note: The Plus palette capabilities are only accessible through the [[Default I/O Port Summary|ASIC I/O page]]. Registers PENR and INKR are not needed in that case.
 +
 
 +
=== Register PENR (Select a color register) ===
 +
 
 +
When bit 7 and bit 6 are set to "0", the remaining bits determine which pen is to have its colour changed. When bit 4 is set to "0", bits 3 to 0 define which pen is to be selected. When bit 4 is set to "1", the value contained in bits 3-0 is ignored and the border is selected.
 +
 
 +
The pen remains selected until another is chosen.
 +
 
 +
Each mode has a fixed number of pens. Mode 0 has 16 pens, mode 1 has 4 pens and mode 2 has 2 pens.
 +
 
 +
==== Summary  ====
 +
 
 +
{| class="wikitable"
 +
!Bit
 +
!Value
 +
!Function
 
|-
 
|-
−
|7||0||rowspan=2|Gate Array function "Colour selection"
+
| 7 || 0 || rowspan="2" | Gate Array PENR register
 
|-
 
|-
−
|6||1
+
| 6 || 0
 
|-
 
|-
−
|5||-||not used
+
| 5 || - || not used
 
|-
 
|-
−
|4||x||rowspan=5|Colour number x
+
| 4 || 1 || Select border
 
|-
 
|-
−
|3||x
+
| 3 || x || rowspan="4" | Ignored
 
|-
 
|-
−
|2||x
+
| 2 || x
 
|-
 
|-
−
|1||x
+
| 1 || x
−
|-
+
−
|0||x
+
 
|-
 
|-
 +
| 0 || x
 
|}
 
|}
  
−
==== Hardware colour palette ====
+
{| class="wikitable"
−
 
+
!Bit
−
{|{{Prettytable|width: 700px; font-size: 2em;}}
+
!Value
−
|''Colour Number''||''Colour Name''||''Color''
+
!Function
 
|-
 
|-
−
|0||White||bgcolor="#808080"|
+
| 7 || 0 || rowspan="2" | Gate Array PENR register
 
|-
 
|-
−
|1||White (note 1)||bgcolor="#808080"|
+
| 6 || 0
 
|-
 
|-
−
|2||Sea Green||bgcolor="#00FF80"|
+
| 5 || - || not used
 
|-
 
|-
−
|3||Pastel Yellow||bgcolor="#FFFF50"|
+
| 4 || 0 || Select pen
 
|-
 
|-
−
|4||Blue||bgcolor="#000080"|
+
| 3 || x || rowspan="4" | Pen number
 
|-
 
|-
−
|5||Purple||bgcolor="#FF0080"|
+
| 2 || x
 
|-
 
|-
−
|6||Cyan||bgcolor="#008080"|
+
| 1 || x
 
|-
 
|-
−
|7||Pink||bgcolor="#FF8080"|
+
| 0 || x
 +
|}
 +
 
 +
<br>
 +
 
 +
=== Register INKR (Change the value of the currently selected color register) ===
 +
 
 +
Once the pen has been selected its colour can then be changed. Bits 4 to 0 specify the hardware colour number from the hardware colour palette.
 +
 
 +
Even though there is provision for 32 colours, only 27 are possible. The remaining colours are duplicates of those already in the colour palette.
 +
 
 +
==== Summary  ====
 +
 
 +
{| class="wikitable"
 +
!Bit
 +
!Value
 +
!Function
 
|-
 
|-
−
|8||Purple (note 1)||bgcolor="#FF0080"|
+
| 7 || 0 || rowspan="2" | Gate Array INKR register
 
|-
 
|-
−
|9||Pastel Yellow (note 1)||bgcolor="#FFFF50"|
+
| 6 || 1
 
|-
 
|-
−
|10||Bright Yellow||bgcolor="#FFFF80"|
+
| 5 || - || not used
 
|-
 
|-
−
|11||Bright White||bgcolor="#FFFFFF"|
+
| 4 || x || rowspan="5" | Colour number x
 
|-
 
|-
−
|12||Bright Red||bgcolor="#FF0000"|
+
| 3 || x
 
|-
 
|-
−
|13||Bright Magenta||bgcolor="#FF00FF"|
+
| 2 || x
 
|-
 
|-
−
|14||Orange||bgcolor="#FF8000"|
+
| 1 || x
−
|-
+
−
|15||Pastel Magenta||bgcolor="#FF80FF"|
+
−
|-
+
−
|16||Blue (note 1)||bgcolor="#000080"|
+
−
|-
+
−
|17||Sea Green (note 1)||bgcolor="#00FF80"|
+
−
|-
+
−
|18||Bright Green||bgcolor="#00FF00"|
+
−
|-
+
−
|19||Bright Cyan||bgcolor="#00FFFF"|
+
−
|-
+
−
|20||Black||bgcolor="#000000"|
+
−
|-
+
−
|21||Bright Blue||bgcolor="#0000FF"|
+
−
|-
+
−
|22||Green||bgcolor="#008000"|
+
−
|-
+
−
|23||Sky Blue||bgcolor="#0080FF"|
+
−
|-
+
−
|24||Magenta||bgcolor="#800080"|
+
−
|-
+
−
|25||Pastel Green||bgcolor="#80FF80"|
+
−
|-
+
−
|26||Lime||bgcolor="#80FF00"|
+
−
|-
+
−
|27||Pastel Cyan||bgcolor="#80FFFF"|
+
−
|-
+
−
|28||Red||bgcolor="#800000"|
+
−
|-
+
−
|29||Mauve||bgcolor="#8000FF"|
+
−
|-
+
−
|30||Yellow||bgcolor="#808000"|
+
−
|-
+
−
|31||Pastel Blue||bgcolor="#8080FF"|
+
 
|-
 
|-
 +
| 0 || x
 
|}
 
|}
  
−
===== Notes =====
+
<br>
  
−
This is not an official colour
+
=== Register RMR (Control Interrupt counter, ROM mapping and Graphics mode) ===
  
−
Select screen mode and rom configuration
+
This is a general purpose register responsible for the [[Video modes|graphics mode]] and the ROM configuration.
  
−
This is a general purpose register responsible for the screen mode and the rom configuration.
+
==== Graphics mode selection  ====
  
−
==== Screen mode selection ====
+
The function of bits 1 and 0 is to define the screen mode. The settings for bits 1 and 0 and the corresponding screen mode are given in the table below.
  
−
The function of bits 1 and 0 is to define the screen mode. The settings for bits 1 and 0 and the corresponding screen mode are given in the table below.
+
{| class="wikitable"
−
 
+
!Bit 1
−
{|{{Prettytable|width: 700px; font-size: 2em;}}
+
!Bit 0
−
|''Bit 1''||''Bit 0''||''Screen mode''
+
!Screen mode
 
|-
 
|-
−
|0||0||Mode 0, 160x200 resolution, 16 colours
+
| 0 || 0 || Mode 0, 160x200 resolution, 16 colours
 
|-
 
|-
−
|0||1||Mode 1, 320x200 resolution, 4 colours
+
| 0 || 1 || Mode 1, 320x200 resolution, 4 colours
 
|-
 
|-
−
|1||0||Mode 2, 640x200 resolution, 2 colours
+
| 1 || 0 || Mode 2, 640x200 resolution, 2 colours
−
|-
+
−
|1||1||Mode 3, 160x200 resolution, 4 colours (note 1)
+
 
|-
 
|-
 +
| 1 || 1 || Mode 3, 160x200 resolution, 4 colours (undocumented)
 
|}
 
|}
  
−
This mode is not official. From the combinations possible, we can see that 4 modes can be defined, although the Amstrad only has 3. Mode 3 is similar to mode 0, because it has the same resolution, but it is limited to only 4 colours.
+
* Mode 3 is not official. From the combinations possible, we can see that 4 modes can be defined, although the Amstrad only has 3. Mode 3 is similar to mode 0, because it has the same resolution, but it is limited to only 4 colours. Mode 3 is not supported by the [[KC Compact]] (which outputs black in Mode 3).
  
 
Mode changing is synchronised with HSYNC. If the mode is changed, it will take effect from the next HSYNC.
 
Mode changing is synchronised with HSYNC. If the mode is changed, it will take effect from the next HSYNC.
  
−
==== Rom configuration selection ====
+
==== ROM configuration selection ====
  
−
Bit 2 is used to enable or disable the lower rom area. The lower rom area occupies memory addressess &amp;0000-&amp;3fff and is used to access the operating system rom. When the lower rom area is is enabled, reading from &amp;0000-&amp;3FFF will return data in the rom. When a value is written to &amp;0000-&amp;3FFF, it will be written to the ram underneath the rom. When it is disabled, data read from &amp;0000-&amp;3FFF will return the data in the ram.
+
Bit 2 is used to enable or disable the lower ROM area. The lower ROM area occupies memory addresses &amp;0000-&amp;3fff and is used to access the operating system ROM. When the lower ROM area is is enabled, reading from &amp;0000-&amp;3FFF will return data in the ROM. When a value is written to &amp;0000-&amp;3FFF, it will be written to the RAM underneath the RAM. When it is disabled, data read from &amp;0000-&amp;3FFF will return the data in the RAM.  
  
−
Similarly, bit 3 controls enabling or disabling of the upper rom area. The upper rom area occupies memory addressess &amp;C000-&amp;FFFF and is BASIC or any expansion roms which may be plugged into a rom board/box. See the document on upper rom selection for more details. When the upper rom area enabled, reading from &amp;c000-&amp;ffff, will return data in the rom. When data is written to &amp;c000-&amp;FFFF, it will be written to the ram at the same address as the rom. When the upper rom area is disabled, and data is read from &amp;c000-&amp;ffff the data returned will be the data in the ram.
+
Similarly, bit 3 controls enabling or disabling of the upper ROM area. The upper ROM area occupies memory addressess &amp;C000-&amp;FFFF and is BASIC or any expansion ROMs which may be plugged into a ROM board/box. See the document on [[Upper ROM Bank Number|upper rom selection]] for more details. When the upper ROM area enabled, reading from &amp;c000-&amp;ffff, will return data in the ROM. When data is written to &amp;c000-&amp;FFFF, it will be written to the RAM at the same address as the ROM. When the upper ROM area is disabled, and data is read from &amp;c000-&amp;ffff it will be the data in the RAM.  
  
−
Bit 4 controls the interrupt generation. It can be used to delay interrupts. See the document on interrupt generation for more information.
+
Bit 4 controls the interrupt generation. It can be used to delay interrupts. See the document on interrupt generation for more information.  
  
−
===== Summary =====
+
==== Summary ====
  
−
{|{{Prettytable|width: 700px; font-size: 2em;}}
+
{| class="wikitable"
−
|''Bit''||''Value''||''Function''
+
!Bit
 +
!Value
 +
!Function
 
|-
 
|-
−
|7||0||rowspan=2|Gate Array function
+
| 7 || 1 || rowspan="2" | Gate Array RMR register
 
|-
 
|-
−
|6||1
+
| 6 || 0
 
|-
 
|-
−
|5||-||not used
+
| 5 || - || ''must be 0 on Plus machines with ASIC unlocked''
 
|-
 
|-
−
|4||x||Interrupt generation control
+
| 4 || x || Interrupt generation control
 
|-
 
|-
−
|3||x||
+
| 3 || x || 1=Upper ROM area disable, 0=Upper ROM area enable
−
*1 Upper rom area disable
+
−
*0 Upper rom area enable
+
 
|-
 
|-
−
|2||x||
+
| 2 || x || 1=Lower ROM area disable, 0=Lower ROM area enable
−
*1 Lower rom area disable
+
−
*0 Lower rom area enable
+
 
|-
 
|-
−
|1||x||rowspan=2|Mode slection
+
| 1 || x || rowspan="2" | Graphics Mode selection
−
|-
+
−
|0||x
+
 
|-
 
|-
 +
| 0 || x
 
|}
 
|}
  
−
== Programming the Gate Array - Examples ==
+
<br>
  
−
Defining the colours, <br>Setting pen 0 to Bright White.
+
=== Register RMR2 (ASIC & Advanced ROM mapping) ===
  
−
<pre>
+
This register exists only in Plus or GX4000, and is only accessible when the ASIC is unlocked.
−
LD BC,7F00 ;Gate Array port
+
−
LD A,%00000000+0 ;Pen number (and Gate Array function)
+
−
OUT (C),A ;Send pen number
+
−
LD A,%01000000+11 ;Pen colour (and Gate Array function)
+
−
OUT (C),A ;Send it
+
−
RET
+
  
−
Setting the mode and rom configuration,
+
{| class="wikitable"
−
Mode 2, upper and lower rom disabled.
+
!Bit
−
 
+
!Value
−
LD BC,7F00 ;Gate array port
+
!Function
−
LD A,%10000000+%00001110 ;Mode and rom selection (and Gate Array function)
+
−
OUT (C),A ;Send it
+
−
RET
+
−
</pre>
+
−
 
+
−
==== Conversion chart ====
+
−
 
+
−
The hardware colour number is different to the colour range used by the firmware, so a conversion chart is provided for the corresponding firmware/hardware colour values and the corresponding colour name.
+
−
 
+
−
===== Note =====
+
−
 
+
−
The firmware keeps track of the colours it is using. Every VSYNC (assuming interrupts are enabled) the firmware sets the colours. This enables the user to have flashing colours. If the user selects a new colour using the gate array, the new colour will flash temporarily and then return to it's original colour. This is due to the firmware re- setting the colour. When using the firmware, use it's routines to select the colour, and the colour will remain.
+
−
 
+
−
{|{{Prettytable|width: 700px; font-size: 2em;}}
+
−
|''Firmware Colour Number''||''Colour Name''||''Hardware Number''||''Quick reference colour value''||''Color''
+
 
|-
 
|-
−
|0||Black||20||&54||bgcolor="#000000"|
+
| 7 || 1 || rowspan="3" | Gate Array RMR2 register
 
|-
 
|-
−
|1||Blue||4||&44||bgcolor="#000080"|
+
| 6 || 0
 
|-
 
|-
−
|2||Bright Blue||21||&55||bgcolor="#0000FF"|
+
| 5 || 1
 
|-
 
|-
−
|3||Red||28||&5C||bgcolor="#800000"|
+
| 4 || x || rowspan="2" |Lower ROM address and ASIC I/O page mode
 
|-
 
|-
−
|4||Magenta||24||&58||bgcolor="#800080"|
+
| 3 || x
 
|-
 
|-
−
|5||Mauve|| 29||&5D||bgcolor="#8000FF"|
+
| 2 || x || rowspan="3" | Physical ROM number (0..7)
 
|-
 
|-
−
|6||Bright Red||12||&4C||bgcolor="#FF0000"|
+
| 1 || x
 
|-
 
|-
−
|7||Purple|| 5||&45||bgcolor="#FF0080"|
+
| 0 || x
−
|-
+
|}
−
|8||Bright Magenta||13||&4D||bgcolor="#FF00FF"|
+
 
−
|-
+
The lower ROM address and [[Default I/O Port Summary|ASIC I/O page]] modes are:
−
|9||Green||22||&56||bgcolor="#008000"|
+
 
−
|-
+
  -Mode-  ROM address    ASIC I/O Page
−
|10||Cyan||6||&46||bgcolor="#008080"|
+
    00    &0000-&3FFF      Disabled
−
|-
+
    01    &4000-&7FFF      Disabled
−
|11||Sky Blue||23||&57||bgcolor="#0080FF"|
+
    10     &8000-&BFFF      Disabled
−
|-
+
    11     &0000-&3FFF    &4000-&7fff
−
|12||Yellow||30||&5E||bgcolor="#808000"|
+
 
−
|-
+
The physical ROMs are also accessible as upper ROMs by using the [[Upper ROM Bank Number]] port and the RMR register.
−
|13||White||0||&40||bgcolor="#808080"|
+
 
−
|-
+
<br>
−
|14||Pastel Blue||31||&5F||bgcolor="#8080FF"|
+
 
 +
=== Register MMR (RAM memory mapping) ===
 +
 
 +
This register exists only in CPCs with 128K RAM (like the CPC 6128, or CPCs with [[Standard Memory Expansions]]). Note: In the CPC 6128, the register is a separate [[PAL16L8|PAL chip]] that assists the Gate Array chip. See its wiki page.
 +
 
 +
{| class="wikitable"
 +
!Bit
 +
!Value
 +
!Function
 
|-
 
|-
−
|15||Orange||14||&4E||bgcolor="#FF8000"|
+
| 7 || 1 || rowspan="2" | Gate Array MMR register
 
|-
 
|-
−
|16||Pink||7||&47||bgcolor="#FF8080"|
+
| 6 || 1
 
|-
 
|-
−
|17||Pastel Magenta||15||&4F||bgcolor="#FF80FF"|
+
| 5 || x || rowspan="3" |64K bank number (0..7); always 0 on an unexpanded CPC6128, 0-7 on [[Standard Memory Expansions]]
 
|-
 
|-
−
|18||Bright Green||18||&52||bgcolor="#00FF00"|
+
| 4 || x
 
|-
 
|-
−
|19||Sea Green||2||&42bgcolor="#00FF80"|
+
| 3 || x
 
|-
 
|-
−
|20||Bright Cyan||19||&53||bgcolor="#00FFFF"|
+
| 2 || x || rowspan="3" | RAM Config (0..7)
 
|-
 
|-
−
|21||Lime||26||&5A||bgcolor="#80FF00"|
+
| 1 || x
−
|-
+
−
|22||Pastel Green||25||&59||bgcolor="#80FF80"|
+
−
|-
+
−
|23||Pastel Cyan||27||&5B||bgcolor="#80FFFF"|
+
−
|-
+
−
|24||Bright Yellow||10||&4A||bgcolor="#FFFF80"|
+
−
|-
+
−
|25||Pastel Yellow||3||&43||bgcolor="#FFFF80"|
+
−
|-
+
−
|26||Bright White||11||&4B||bgcolor="#FFFFFF"|
+
 
|-
 
|-
 +
| 0 || x
 
|}
 
|}
  
−
This chart also gives a quick reference guide for programming the colours. The number is the colour number which can be sent directly, once the pen has been selected, to get the colour wanted.
 
  
−
Example:
+
The 3bit RAM Config value is used to access the second 64K of the total 128K RAM that is built into the CPC 6128 or the additional 64K-512K of standard memory expansions. These contain up to eight 64K ram banks, which are selected with bit 3-5. A standard CPC 6128 only contains bank 0. Normally the register is set to 0, so that only the first 64K RAM are used (identical to the CPC 464 and 664 models). The register can be used to select between the following eight predefined configurations only:
  
−
<pre>
+
  -Address-    0      1      2      3      4      5      6      7
−
ld bc,7f00+1 ;Gate array function (set pen)
+
  0000-3FFF  RAM_0  RAM_0  '''RAM_4'''  RAM_0  RAM_0  RAM_0  RAM_0  RAM_0
 +
  4000-7FFF  RAM_1  RAM_1  '''RAM_5'''  '''RAM_3'''  '''RAM_4'''  '''RAM_5'''  '''RAM_6'''  '''RAM_7'''
 +
  8000-BFFF  RAM_2  RAM_2  '''RAM_6'''  RAM_2  RAM_2  RAM_2  RAM_2  RAM_2
 +
  C000-FFFF  RAM_3  '''RAM_7'''  '''RAM_7'''  '''RAM_7'''  RAM_3  RAM_3  RAM_3  RAM_3
 +
 
 +
The Video RAM is always located in the first 64K, VRAM is in no way affected by this register.
 +
 
 +
<br>
 +
 
 +
== Programming the Gate Array - Examples  ==
 +
 
 +
Defining the colours, <br>Setting pen 0 to Bright White.
 +
<pre>LD BC,7F00&nbsp;;Gate Array port
 +
LD A,%00000000+0&nbsp;;Pen number (and Gate Array function)
 +
OUT (C),A&nbsp;;Send pen number
 +
LD A,%01000000+11&nbsp;;Pen colour (and Gate Array function)
 +
OUT (C),A&nbsp;;Send it
 +
RET
 +
 
 +
Setting the mode and ROM configuration,
 +
Mode 2, upper and lower ROM disabled.
 +
 
 +
LD BC,7F00&nbsp;;Gate array port
 +
LD A,%10000000+%00001110&nbsp;;Mode and ROM selection (and Gate Array function)
 +
OUT (C),A&nbsp;;Send it
 +
RET
 +
</pre>
 +
 
 +
=== Misc ===
 +
 
 +
The hardware colour number is different to the colour range used by the firmware, so a conversion chart is provided for the corresponding firmware/hardware colour values and the corresponding colour name.
 +
 
 +
=== Note ===
 +
 
 +
The firmware keeps track of the colours it is using. Every VSYNC (assuming interrupts are enabled) the firmware sets the colours. This enables the user to have flashing colours. If the user selects a new colour using the gate array, the new colour will flash temporarily and then return to its original colour. This is due to the firmware resetting the colour. When using the firmware, use its routines to select the colour, and the colour will remain.
 +
 
 +
Example: [For whatever reason, this example does NOT refer to the above firmware stuff]
 +
<pre>ld bc,7f00+1&nbsp;;Gate array function (set pen)
 
;and pen number
 
;and pen number
 
out (c),c
 
out (c),c
−
ld bc,7f00 ;41  
+
ld bc,7f00&nbsp;;41  
 
;Gate array function (set colour)
 
;Gate array function (set colour)
 
;and colour number
 
;and colour number
Line 363: Line 415:
 
</pre>
 
</pre>
  
−
==== Pallette R,G,B definitions ====
+
<br>
 +
 
 +
== Video memory structure ==
 +
 
 +
{| class="wikitable"
 +
!rowspan=2|Graphics Mode
 +
!colspan=8|VRAM byte
 +
!colspan=8|Displayed Pixels
 +
!rowspan=2|Definition
 +
|-
 +
!7
 +
!6
 +
!5
 +
!4
 +
!3
 +
!2
 +
!1
 +
!0
 +
!1
 +
!2
 +
!3
 +
!4
 +
!5
 +
!6
 +
!7
 +
!8
 +
|-
 +
|0
 +
|A0
 +
|B0
 +
|A2
 +
|B2
 +
|A1
 +
|B1
 +
|A3
 +
|B3
 +
|colspan=4 style="text-align: center;"|A
 +
|colspan=4 style="text-align: center;"|B
 +
|2 pixels in 16 colors
 +
|-
 +
|1
 +
|A0
 +
|B0
 +
|C0
 +
|D0
 +
|A1
 +
|B1
 +
|C1
 +
|D1
 +
|colspan=2 style="text-align: center;"|A
 +
|colspan=2 style="text-align: center;"|B
 +
|colspan=2 style="text-align: center;"|C
 +
|colspan=2 style="text-align: center;"|D
 +
|4 pixels in 4 colours
 +
|-
 +
|2
 +
|A0
 +
|B0
 +
|C0
 +
|D0
 +
|E0
 +
|F0
 +
|G0
 +
|H0
 +
|A
 +
|B
 +
|C
 +
|D
 +
|E
 +
|F
 +
|G
 +
|H
 +
|8 pixels in 2 colors
 +
|-
 +
|3
 +
|A0
 +
|B0
 +
|x
 +
|x
 +
|A1
 +
|B1
 +
|x
 +
|x
 +
|colspan=4 style="text-align: center;"|A
 +
|colspan=4 style="text-align: center;"|B
 +
|2 pixels in 4 colors
 +
|}
 +
 
 +
<br>
 +
 
 +
== Split rasters ==
 +
 
 +
On the CPC, split rasters occur halfway (after the 8th mode2 pixel) through the rendering of a CRTC character.
 +
 
 +
On Amstrad Plus, split rasters occur quarter of the way (after the 4th mode2 pixel) through the rendering of a CRTC character.
 +
 
 +
To easily make split rasters compatible with both the CPC and the Plus machines, one can use the ASIC soft-scroll control register (SSCR) to finely adjust the horizontal position of the graphics.
 +
 
 +
<br>
 +
 
 +
== Palette R,G,B definitions ==
  
−
There are 27 colours which are generated from red, green and blue mixed in different quantities. There are 3 levels of red, 3 levels of green and 3 levels of blue, and these can be thought of as off/no colour, half-on/half-colour, and on/full-colour.
+
There are 27 colours which are generated from red, green and blue mixed in different quantities. There are 3 levels of red, 3 levels of green and 3 levels of blue, and these can be thought of as off/no colour, half-on/half-colour, and on/full-colour.  
  
 
To display a CPC image you will need to use a analogue monitor with a composite sync.
 
To display a CPC image you will need to use a analogue monitor with a composite sync.
  
−
This table shows the relationship between hardware colour number, colour name and RGB mixing.
+
<br>
  
 +
=== Palette sorted by Hardware Colour Numbers ===
  
−
{|{{Prettytable|width: 700px; font-size: 2em;}}
+
{| class="FCK__ShowTableBorders"
−
|''Hardware Colour Index''||''Colour Name''||''R %''||''G %''||''B %''||''Color''
+
 
|-
 
|-
−
|0||White||align="right"|50||align="right"|50||align="right"|50||bgcolor="#808080"|
+
| ''Hardware Number||Firmware Number|| ''Colour Name''
 +
| ''R&nbsp;%'' || ''G&nbsp;%'' || ''B&nbsp;%'' || ''ASIC'' || ''Colour''
 
|-
 
|-
−
|1||White||align="right"|50||align="right"|50||align="right"|50||bgcolor="#808080"|
+
| 0 (40h) || 13  || White        || 50|| 50|| 50|| #666|| bgcolor="#808080" |  
 
|-
 
|-
−
|2||Sea Green||align="right"|0||align="right"|100||align="right"|50||bgcolor="#00FF80"|
+
| 1 (41h) || (13) || White        || 50|| 50|| 50|| #666|| bgcolor="#808080" |  
 
|-
 
|-
−
|3||Pastel Yellow||align="right"|100||align="right"|100||align="right"|50||bgcolor="#FFFF80"|
+
| 2 (42h) || 19  || Sea Green    || 0||100|| 50|| #0F6|| bgcolor="#00ff80" |  
 
|-
 
|-
−
|4||Blue||align="right"|0||align="right"|0||align="right"|50||bgcolor="#000080"|
+
| 3 (43h) || 25  || Pastel Yellow ||100||100|| 50|| #FF6|| bgcolor="#ffff80" |  
 
|-
 
|-
−
|5||Purple||align="right"|100||align="right"|0||align="right"|50||bgcolor="#FF0080"|
+
| 4 (44h) || 1    || Blue          || 0|| 0|| 50|| #006|| bgcolor="#000080" |  
 
|-
 
|-
−
|6||Cyan||align="right"|0||align="right"|50||align="right"|50||bgcolor="#008080"|
+
| 5 (45h) || 7    || Purple        ||100||  0|| 50|| #F06|| bgcolor="#ff0080" |
 
|-
 
|-
−
|7||Pink||align="right"|100||align="right"|50||align="right"|50||bgcolor="#FF8080"|
+
| 6 (46h) || 10  || Cyan          || 0|| 50|| 50|| #066|| bgcolor="#008080" |  
 
|-
 
|-
−
|8||Purple||align="right"|100||align="right"|0||align="right"|50||bgcolor="#FF0080"|
+
| 7 (47h) || 16  || Pink          ||100|| 50|| 50|| #F66|| bgcolor="#ff8080" |  
 
|-
 
|-
−
|9||Pastel Yellow||align="right"|100||align="right"|100||align="right"|50||bgcolor="#FFFF80"|
+
| 8 (48h) || (7)  || Purple        ||100|| 0|| 50|| #F06|| bgcolor="#ff0080" |  
 
|-
 
|-
−
|10||Bright Yellow||align="right"|100||align="right"|100||align="right"|0||bgcolor="#FFFF00"|
+
| 9 (49h) || (25) || Pastel Yellow ||100||100|| 50|| #FF6|| bgcolor="#ffff80" |  
 
|-
 
|-
−
|11||Bright White||align="right"|100||align="right"|100||align="right"|100||bgcolor="#FFFFFF"|
+
| 10 (4Ah) || 24  || Bright Yellow ||100||100|| 0|| #FF0|| bgcolor="#ffff00" |  
 
|-
 
|-
−
|12||Bright Red||align="right"|100||align="right"|0||align="right"|0||bgcolor="#FF0000"|
+
| 11 (4Bh) || 26  || Bright White  ||100||100||100|| #FFF|| bgcolor="#ffffff" |  
 
|-
 
|-
−
|13||Bright Magenta||align="right"|100||align="right"|0||align="right"|100||bgcolor="#FF00FF"|
+
| 12 (4Ch) || 6    || Bright Red    ||100|| 0||  0|| #F00|| bgcolor="#ff0000" |  
 
|-
 
|-
−
|14||Orange||align="right"|100||align="right"|50||align="right"|0||bgcolor="#FF8000"|
+
| 13 (4Dh) || 8    || Bright Magenta||100|| 0||100|| #F0F|| bgcolor="#ff00ff" |  
 
|-
 
|-
−
|15||Pastel Magenta||align="right"|100||align="right"|50||align="right"|100||bgcolor="#FF80FF"|
+
| 14 (4Eh) || 15   || Orange        ||100|| 50|| 0|| #F60|| bgcolor="#ff8000" |  
 
|-
 
|-
−
|16||Blue||align="right"|0||align="right"|0||align="right"|50||bgcolor="#000080"|
+
| 15 (4Fh) || 17  || Pastel Magenta||100|| 50||100|| #F6F|| bgcolor="#ff80ff" |  
 
|-
 
|-
−
|17||Sea Green||align="right"|0||align="right"|100||align="right"|50||bgcolor="#00FF80"|
+
| 16 (50h) || (1)  || Blue          || 0|| 0|| 50|| #006|| bgcolor="#000080" |  
 
|-
 
|-
−
|18||Bright Green||align="right"|0||align="right"|100||align="right"|0||bgcolor="#00FF00"|
+
| 17 (51h) || (19) || Sea Green     || 0||100|| 50|| #0F6|| bgcolor="#00ff80" |  
 
|-
 
|-
−
|19||Bright Cyan||align="right"|0||align="right"|100||align="right"|100||bgcolor="#00FFFF"|
+
| 18 (52h) || 18  || Bright Green  || 0||100|| 0|| #0F0|| bgcolor="#00ff00" |  
 
|-
 
|-
−
|20||Black||align="right"|0||align="right"|0||align="right"|0||bgcolor="#000000"|
+
| 19 (53h) || 20   || Bright Cyan  || 0||100||100|| #0FF|| bgcolor="#00ffff" |  
 
|-
 
|-
−
|21||Bright Blue||align="right"|0||align="right"|0||align="right"|100||bgcolor="#0000FF"|
+
| 20 (54h) || 0    || Black        ||  0|| 0||  0|| #000|| bgcolor="#000000" |
 
|-
 
|-
−
|22||Green||align="right"|0||align="right"|50||align="right"|0||bgcolor="#008000"|
+
| 21 (55h) || 2    || Bright Blue  || 0|| 0||100|| #00F|| bgcolor="#0000ff" |  
 
|-
 
|-
−
|23||Sky Blue||align="right"|0||align="right"|50||align="right"|100||bgcolor="#0080FF"|
+
| 22 (56h) || 9    || Green        || 0|| 50|| 0|| #060|| bgcolor="#008000" |  
 
|-
 
|-
−
|24||Magenta||align="right"|50||align="right"|0||align="right"|50||bgcolor="#800080"|
+
| 23 (57h) || 11  || Sky Blue      || 0|| 50||100|| #06F|| bgcolor="#0080ff" |  
 
|-
 
|-
−
|25||Pastel Green||align="right"|50||align="right"|100||align="right"|50||bgcolor="#80FF80"|
+
| 24 (58h) || 4    || Magenta      || 50|| 0|| 50|| #606|| bgcolor="#800080" |  
 
|-
 
|-
−
|26||Lime||align="right"|50||align="right"|100||align="right"|0||bgcolor="#80FF00"|
+
| 25 (59h) || 22  || Pastel Green  || 50||100|| 50|| #6F6|| bgcolor="#80ff80" |  
 
|-
 
|-
−
|27||Pastel Cyan||align="right"|50||align="right"|100||align="right"|100||bgcolor="#80FFFF"|
+
| 26 (5Ah) || 21  || Lime          || 50||100|| 0|| #6F0|| bgcolor="#80ff00" |  
 
|-
 
|-
−
|28||Red||align="right"|50||align="right"|0||align="right"|0||bgcolor="#800000"|
+
| 27 (5Bh) || 23  || Pastel Cyan  || 50||100||100|| #6FF|| bgcolor="#80ffff" |  
 
|-
 
|-
−
|29||Mauve||align="right"|50||align="right"|0||align="right"|100||bgcolor="#8000FF"|
+
| 28 (5Ch) || 3    || Red          || 50|| 0|| 0|| #600||bgcolor="#800000" |  
 
|-
 
|-
−
|30||Yellow||align="right"|50||align="right"|50||align="right"|0||bgcolor="#808000"|
+
| 29 (5Dh) || 5    || Mauve        || 50|| 0||100|| #60F||bgcolor="#8000ff" |  
 
|-
 
|-
−
|31||Pastel Blue||align="right"|50||align="right"|50||align="right"|100||bgcolor="#8080FF"|
+
| 30 (5Eh) || 12  || Yellow        || 50|| 50|| 0|| #660||bgcolor="#808000" |  
 
|-
 
|-
 +
| 31 (5Fh) || 14  || Pastel Blue  || 50|| 50||100|| #66F||bgcolor="#8080ff" |
 
|}
 
|}
  
−
==== RGB assignments for the software colours ====
+
<br>
  
−
This is simply a sidenote to illustrate a pattern in the RGB assignments of the software colours and to show how their value is calculated.
+
=== Palette sorted by Firmware Colour Numbers ===
  
−
{|{{Prettytable|width: 700px; font-size: 2em;}}
+
{| class="FCK__ShowTableBorders"
−
|''Firmware Colour Number''||''Colour Name''||''R %''||''G %''||''B %''||''Color''
+
 
|-
 
|-
−
|0||Black||0||0||0||bgcolor="#000000"|  
+
| ''Firmware Number'' || ''Hardware Number'' || ''Colour Name''
 +
| ''R&nbsp;%'' || ''G&nbsp;%'' || ''B&nbsp;%'' || ''ASIC'' || ''Colour''
 
|-
 
|-
−
|1||Blue||0||0||50||bgcolor="#000080"|  
+
| 0|| 54h          ||Black          ||  0|| 0|| 0|| #000||bgcolor="#000000"|
 
|-
 
|-
−
|2||Bright Blue||0||0||100||bgcolor="#0000FF"|
+
| 1|| 44h (or 50h) ||Blue           || 0|| 0|| 50|| #006||bgcolor="#000080"|
 
|-
 
|-
−
|3||Red||50||0||0||bgcolor="#800000"|
+
| 2|| 55h          ||Bright Blue    || 0|| 0||100|| #00F||bgcolor="#0000ff"|
 
|-
 
|-
−
|4||Magenta||50||0||50||bgcolor="#800080"|
+
| 3|| 5Ch          ||Red            || 50|| 0|| 0|| #600||bgcolor="#800000"|
 
|-
 
|-
−
|5||Mauve||50||0||100||bgcolor="#8000FF"|
+
| 4|| 58h          ||Magenta        || 50|| 0|| 50|| #606||bgcolor="#800080"|
 
|-
 
|-
−
|6||Bright Red||100||0||0||bgcolor="#FF0000"|
+
| 5|| 5Dh          ||Mauve          || 50|| 0||100|| #60F||bgcolor="#8000ff"|
 
|-
 
|-
−
|7||Purple||100||0||50||bgcolor="#FF0080"|
+
| 6|| 4Ch          ||Bright Red    ||100|| 0|| 0|| #F00||bgcolor="#ff0000"|
 
|-
 
|-
−
|8||Bright Magenta||100||0||100||bgcolor="#FF00FF"|
+
| 7|| 45h (or 48h) ||Purple        ||100|| 0|| 50|| #F06||bgcolor="#ff0080"|
 
|-
 
|-
−
|9||Green||0||50||0||bgcolor="#008000"|
+
| 8|| 4Dh          ||Bright Magenta ||100|| 0||100|| #F0F||bgcolor="#ff00ff"|
 
|-
 
|-
−
|10||Cyan||0||50||50||bgcolor="#008080"|
+
| 9|| 56h          ||Green          ||  0|| 50|| 0|| #060||bgcolor="#008000"|
 
|-
 
|-
−
|11||Sky Blue||0||50||100||bgcolor="#0080FF"|
+
|10|| 46h          ||Cyan          ||  0|| 50|| 50|| #066||bgcolor="#008080"|
 
|-
 
|-
−
|12||Yellow||50||50||0||bgcolor="#808000"|
+
|11|| 57h          ||Sky Blue      ||  0|| 50||100|| #06F||bgcolor="#0080ff"|
 
|-
 
|-
−
|13||White||50||50||50||bgcolor="#808080"|
+
|12|| 5Eh          ||Yellow        || 50|| 50||  0|| #660||bgcolor="#808000"|
 
|-
 
|-
−
|14||Pastel Blue||50||50||100||bgcolor="#8080FF"|
+
|13|| 40h (or 41h) ||White          || 50|| 50|| 50||#666||bgcolor="#808080"|
 
|-
 
|-
−
|15||Orange||100||50||0||bgcolor="#FF8000"|
+
|14|| 5Fh          ||Pastel Blue    || 50|| 50||100|| #66F||bgcolor="#8080ff"|
 
|-
 
|-
−
|16||Pink||100||50||50||bgcolor="#FF8080"|
+
|15|| 4Eh          ||Orange        ||100|| 50|| 0|| #F60|| bgcolor="#ff8000"|
 
|-
 
|-
−
|17||Pastel Magenta||100||50||100||bgcolor="#FF80FF"|
+
|16|| 47h          ||Pink          ||100|| 50|| 50|| #F66||bgcolor="#ff8080"|
 
|-
 
|-
−
|18||Bright Green||0||100||0||bgcolor="#00FF00"|
+
|17|| 4Fh          ||Pastel Magenta ||100|| 50||100|| #F6F||bgcolor="#ff80ff"|
 
|-
 
|-
−
|19||Sea Green||0||100||50||bgcolor="#00FF80"|
+
|18|| 52h          ||Bright Green   || 0||100|| 0|| #0F0||bgcolor="#00ff00"|
 
|-
 
|-
−
|20||Bright Cyan||0||100||100||bgcolor="#00FFFF"|
+
|19|| 42h (or 51h) ||Sea Green      ||  0||100|| 50|| #0F6||bgcolor="#00ff80"|
 
|-
 
|-
−
|21||Lime||50||100||0||bgcolor="#80FF00"|
+
|20|| 53h          ||Bright Cyan    ||  0||100||100|| #0FF||bgcolor="#00ffff"|
 
|-
 
|-
−
|22||Pastel Green||50||100||50||bgcolor="#80FF80"|
+
|21|| 5Ah          ||Lime          || 50||100|| 0|| #6F0||bgcolor="#80ff00"|
 
|-
 
|-
−
|23||Pastel Cyan||50||100||100||bgcolor="#80FFFF"|
+
|22|| 59h          ||Pastel Green  || 50||100|| 50|| #6F6||bgcolor="#80ff80"|
 
|-
 
|-
−
|24||Bright Yellow||100||100||0||bgcolor="#FFFF00"|
+
|23|| 5Bh          ||Pastel Cyan    || 50||100||100|| #6FF||bgcolor="#80ffff"|
 
|-
 
|-
−
|25||Pastel Yellow||100||100||50||bgcolor="#FFFF80"|
+
|24|| 4Ah          ||Bright Yellow ||100||100|| 0|| #FF0||bgcolor="#ffff00"|
 
|-
 
|-
−
|26||Bright White||100||100||100||bgcolor="#FFFFFF"|
+
|25|| 43h (or 49h) ||Pastel Yellow  ||100||100|| 50||#FF6||bgcolor="#ffff80"|
 
|-
 
|-
 +
|26|| 4Bh          ||Bright White  ||100||100||100|| #FFF||bgcolor="#ffffff"|
 
|}
 
|}
  
−
===== To calculate the colour value =====
+
<br>
  
−
'''Red'''
+
=== Intensities ===
 +
 
 +
The 0%, 50%, and 100% values in the above tables are "should-be" values. However, the real hardware doesn't exactly match that intensities. The actual intensities depend on the luminance mixing (R,G,B tied together via resistors), on chipset (classic CPC, or newer ASIC ones), and on the load applied by external hardware (Monitor, or TV set).
 +
 
 +
On an actual Amstrad CPC, the half-intensity colour signal is measured to be closer to 40% rather than the expected 50%. This was verified by Grim and independently confirmed by Nocash. [https://www.grimware.org/doku.php/documentations/devices/gatearray#inkr Source]
 +
* [[CPC Palette]] - some more details
 +
 
 +
This explains why the Amstrad engineers used these values to adapt the old colour palette to the new 12-bit palette on the Amstrad Plus:
 +
* 0% became #0
 +
* 50% became #6
 +
* 100% became #F
 +
 
 +
They specifically chose #6 for the 50% value instead of #7, to better match the real Amstrad CPC palette.
 +
 
 +
<br>
 +
 
 +
=== Green Screen Colours ===
 +
 
 +
On a green screen (where all colours are shades of unsaturated green), the colours (in BASIC colours) are in order of increasing intensity. Black is very dark, and white is bright green, and colour 13 is a medium green. (Thanks to [[Mark Rison|Mark Rison]] for this information)
 +
 
 +
The luminance (Y) is not exactly correlated to the actual luminance of colour images broadcast in RGB. We have other values.
 +
 
 +
Amstrad preferred to propose a completely different image system, not comparable to a conversion to monochrome, which would have limited the number of brightness levels to 21 (for example, colours 9 and 6 would have had the same luminance).
 +
 
 +
They opted for a table of 27 linear brightness steps. They assigned values of 1 (1kΩ) for blue, 3 (3.3kΩ) for red, and 9 (10kΩ) for green.
 +
 
 +
<br>
 +
 
 +
=== To calculate the luminance value ===
 +
 
 +
'''Red'''  
  
 
0% =&gt; do not add anything  
 
0% =&gt; do not add anything  
  
−
50% =&gt; add 3
+
50% =&gt; add 3  
 +
 
 +
100% =&gt; add 6
 +
 
 +
'''Green'''
 +
 
 +
0% =&gt; do not add anything
 +
 
 +
50% =&gt; add 9
 +
 
 +
100% =&gt; add 18
 +
 
 +
'''Blue'''
 +
 
 +
0% =&gt; do not add anything
 +
 
 +
50% =&gt; add 1
 +
 
 +
100% =&gt; add 2
 +
 
 +
<br>
 +
 
 +
== Pictures ==
  
−
100% =&gt; add 6
+
<gallery>
 +
Image:40010_am2_metal.jpg|40010 GA Metal Layer
 +
Image:40010_am2_acid.jpg|40010 GA with Metal Layer removed
 +
Image:40226_am4_metal.jpg|40226 PreASIC Metal Layer
 +
</gallery>
  
−
'''Green'''
+
[[File:Ga.pinout.40007.png]] [[File:Ga.pinout.40008.40010.png]]
  
−
0% =&gt; do not add anything
+
Note: Some CPC motherboards can accommodate both types of Gate Array pinouts. [https://thecheshirec.at/2024/10/06/il-existe-une-carte-multi-gate-array-et-cest-amstrad-qui-la-faite/ Source]
  
−
50% =&gt; add 9
+
<br>
  
−
100% =&gt; add 18
+
== External links ==
 +
*[https://bread80.com/2021/06/03/understanding-the-amstrad-cpc-video-ram-and-gate-array-subsystem/ Electronic signals analysis of the Gate Array by Bread80]
 +
* [https://www.grimware.org/doku.php/documentations/devices/gatearray Gate Array documentation from Grimware]
 +
* [http://quasar.cpcscene.net/doku.php?id=assem:gate_array Quasar Gate Array documentation (in french)]
  
−
'''Blue'''
+
<br>
  
−
0% =&gt; do not add anything
+
==See also==
  
−
50% =&gt; add 1
+
*[[Gate Array and ASIC Pin-Outs]]
 +
*[[PAL16L8]] : for RAM arrangement
 +
*[[ASIC]] : for Plus users
  
−
100% =&gt; add 2
+
*[[CRTC]] : the other video stuff
 +
*[[Synchronising with the CRTC and display]] : technical details on the relationship between Gate Array and CRTC.
  
−
Green Screen Colours
+
*[[Video modes]] : for other informations on colours and pixels.
  
−
On a green screen (where all colours are shades of green), the colours (in the software/firmware colours), are in order of increasing intensity. So that black is very dark, and white is bright green, and colour 13 is a medium green. (Thanks to [[Mark Rison]] for this information)
+
*[[Media:40010-simplified V03.pdf]] [https://www.cpcwiki.eu/forum/amstrad-cpc-hardware/gate-array-decapped!/msg170713/#msg170713 Forum thread] Gate Array schematics - reverse engineered by Gerald
  
−
[[Category:Hardware]]
+
[[Category:Hardware]][[Category:Programming]][[Category:Datasheet]][[Category:Graphic]][[Category:CPC Internal Components]][[Category:Electronic Component]]

Latest revision as of 16:23, 16 November 2024

Gate Array

Also designated as Video gate Array (VGA, not to be confused with IBM PC compatible graphic card spec).


Introduction

The Gate Array is a specially designed chip exclusively for use in the Amstrad CPC and was designed by Amstrad plc.

In the CPC+ system, the functions of the Gate Array are integrated into a single ASIC. When the ASIC is "locked", the extra features are not available and the ASIC operates the same as the Gate Array in the CPC allowing programs written for the CPC to work on the Plus without modification. The ASIC must be "un-locked" to access the new features.

In the KC Compact system, the functions of the Gate Array are "emulated" in TTL chips, CIO, and its color translation EPROM.

In the "cost-down" version of the CPC6128, the functions of the Gate Array are integrated into a ASIC.


What does it do?

The Gate Array is responsible for the display (colour palette, resolution, horizontal and vertical sync), bus arbitration, DRAM refresh, interrupt generation and memory arrangement.


Bus arbitration

The Gate Array arbitrates access to the RAM between the CPU and the video hardware (CRTC and Gate-Array).

Every microsecond:

  • The CRTC generates a memory address using it's MA and RA signal outputs. See the CRTC wiki page to know how the motherboard wiring transforms these signals into the Video Memory Address (VMA).
  • The Gate Array fetches 2 bytes for each address. /CPU_ADDR is a 1MHz signal. So these 2 bytes are fetched sequentially. They are not interleaved with Z80 access. These bytes are fetched even when the border is on as this is required for DRAM refresh.
  • The video hardware is given priority so that the display is not disrupted.

The Gate-Array generates the "READY" signal which is connected to the "/WAIT" input signal of the CPU. This signal is used to stop the CPU accessing RAM while the video-hardware is accessing it.

In fact, the Gate Array allows the Z80 to access the RAM in only 1 out of every 4 cycles. As a result, all instruction timings are stretched so that they are all multiples of a microsecond (1µs), and this gives an effective CPU clock of 3.3Mhz.

Unlike the ZX Spectrum or the Amiga, where bus arbitration is restricted to the "contended memory" or "chip RAM", on the CPC it also applies to ROM access and to RAM expansions. So the Z80 always runs at the same speed, regardless of the type of memory being accessed.

Last but not least, bus arbitration also applies to I/O access. And memory access is not aligned with I/O access on Z80.

Note: On Amstrad Plus, the ASIC also has to handle DMA instruction fetch from RAM.


DRAM refresh

On Amstrad CPC, the Gate Array is responsible for the DRAM refresh, instead of using the Z80 built-in DRAM refresh mechanism. The reason is that there can only be 3 DRAM accesses per microsecond on this architecture. Doing DRAM refresh on each M1 cycle as it is done on MSX would bog down the CPU speed on CPC given its bus arbitration scheme.

The Z80 generates a maximum of one request per microsecond. The CPC also requires two memory accesses per microsecond for reading video data.

The CPC specs 4164-20 DRAMs. These require 330nS for a read or write cycle. The CPC also uses the optimised sequential CAS cycles to read the two video data bytes in half a microsecond. Source

The way to cause the RAM refresh to fail in both a Plus or normal CPC is simply to stop a few bits of the CRTC address changing (ie. never refresh the selected area).

Generally, only the Row address needs to be cycled, so stopping MA0 through MA7 from changing, and stopping the CPU from reading those rows, will cause data to be lost, quite quickly (generally around 4ms). Source


Interrupt generation

Interrupts on the CPC are created by the Gate Array based on settings from the CRTC. The Gate Array has an internal counter R52 (the R is for Raster) that counts from 0 to 51, incrementing after each HSYNC signal.

On all CRTCs, R52 interrupts always start 1µs after the end of an HSYNC. But on CRTCs 3/4, HSYNCs occur 1µs later than on CRTCs 0/1/2. Which means that on CRTCs 3/4, interrupts start 1µs later than on CRTCs 0/1/2. This can be adjusted by using the CRTC register 3.

R52 will return to 0 and the Gate Array will send an interrupt request on any of these conditions:

  • When it exceeds 51
  • By setting bit4 of the RMR register of the Gate Array to 1
  • At the end of the 2nd HSYNC after the start of the VSYNC

When the Gate Array sends an interrupt request:

  • If the interrupts were authorized at the time of the request, then bit5 of R52 is cleared (but R52 was reset to 0 anyway) and the interrupt takes place
  • If interrupts are not authorized, then the R52 counter continues to increment and the interrupt remains armed (the Gate Array then maintains its INT signal). When interrupts are enabled (using the EI instruction), bit5 of R52 is cleared and the interrupt takes place. This happens only after the instruction that follows EI as this Z80 instruction has a 1-instruction delay.

Note: On Amstrad Plus, the interrupt management system is seriously beefed up. See the ASIC wiki page.


CSYNC signal

The HSYNC and VSYNC signals are received from the CRTC. These signals are then modified by the Gate Array to C-HSYNC and C-VSYNC and merged into a single CSYNC signal that will be sent to the display.

When CRTC HSYNC is active, the Gate Array immediately outputs the palette colour black. If the HSYNC is set to 14 characters then black will be output for 14µs.

If a graphics mode change is pending, the HSYNC pulse width needs to be at least 2µs for Gate Array to change the graphics mode.

C-HSYNC begins 2µs after activation of the CRTC HSYNC and stays a maximum of 4µs (signal is cut short if HSYNC width is greater than 6).

For example, if CRTC R2=46, and CRTC HSYNC width is 14 chars then C-HSYNC starts at 48 and lasts only until 51 included.

On Gate Array, even if the duration of the CRTC VSYNC is reduced to 2 µseconds, the Gate Array will always output black for 26 lines with 4 lines of C-VSYNC to the monitor. While on ASIC/Pre-ASIC, the CRTC VSYNC must be active as long as the C-VSYNC signal is sent to the monitor.

The Gate Array (and ASIC/Pre-ASIC) uses 2 internal counters to create its CSYNC signal:

  • H06 counts the number of CRTC characters processed during an HSYNC. H06 is incremented by the Gate Array for each CRTC character when CRTC HSYNC is active. The Gate Array activates the C-HSYNC signal when H06 reaches 2, and changes its graphics mode if a change was pending. It deactivates this signal when H06 reaches 6.
  • V26 counts the number of HSYNCs occuring during a VSYNC. V26 is incremented by the Gate Array when the CRTC signals an end of HSYNC. The Gate Array activates the C-VSYNC signal when V26 reaches 2 (and if VSYNC is active on ASIC/Pre-ASIC). It deactivates this signal when V26 reaches 6. After the 26th line has been processed, the Gate Array stops outputting the palette colour black.

If CRTC VSYNC is activated again while V26 is still in progress, then V26 is reset to 0 and starts counting up again the HSYNC pulses.

The HSYNC signal from the CRTC is 0 when inactive and 1 when active. Same for VSYNC.

C-HSYNC and C-VSYNC are composited using the XNOR function. The resulting CSYNC signal produced by the Gate Array is 1 when inactive and 0 when active.

On a CPC monitor, the CSYNC is rendered in "absolute black". It is darker than the palette colour black output by the Gate Array. The electron beam is basically turned off. Turning up the brightness level won't make it any brighter.


Controlling the Gate Array

The gate array is controlled by I/O. The gate array is selected when bit 15 of the I/O port address is set to "0" and bit 14 of the I/O port address is set to "1". The values of the other bits are ignored. However, to avoid conflict with other devices in the system, these bits should be set to "1".

The recommended I/O port address is &7Fxx.

The function to be performed is selected by writing data to the Gate Array, the first bits of the data define the function selected (see table below). It is not possible to read from the Gate Array.

8bit command Machine Register Description Chip
7 6 5 4..0
0 0 x n All PENR Select a color register Gate Array
0 1 x n All INKR Change the value of the currently selected color register Gate Array
1 0 0 n All RMR Control Interrupt counter, ROM mapping and Graphics mode Gate Array
1 0 1 n All RMR Ghost register Gate Array (CPC) or locked ASIC (Plus)
1 0 1 n Plus RMR2 ASIC & Advanced ROM mapping Unlocked ASIC
1 1 n All MMR RAM memory mapping PAL (only with 128KB or RAM expansion)

The MMR register is not available in the Gate Array, but is performed by a device at the same I/O port address location.

In the CPC464, CPC664 and KC compact, MMR is performed in an external memory expansion (e.g. Dk'Tronics 64K RAM Expansion), if this expansion is not present then MMR is not available.

In the CPC6128, MMR is performed by a PAL located on the main PCB, or an external memory expansion.

In the 464+ and 6128+, MMR is performed by the ASIC or an external memory expansion. Please read the document on RAM management for more information.


Registers

Note: The Plus palette capabilities are only accessible through the ASIC I/O page. Registers PENR and INKR are not needed in that case.

Register PENR (Select a color register)

When bit 7 and bit 6 are set to "0", the remaining bits determine which pen is to have its colour changed. When bit 4 is set to "0", bits 3 to 0 define which pen is to be selected. When bit 4 is set to "1", the value contained in bits 3-0 is ignored and the border is selected.

The pen remains selected until another is chosen.

Each mode has a fixed number of pens. Mode 0 has 16 pens, mode 1 has 4 pens and mode 2 has 2 pens.

Summary

Bit Value Function
7 0 Gate Array PENR register
6 0
5 - not used
4 1 Select border
3 x Ignored
2 x
1 x
0 x
Bit Value Function
7 0 Gate Array PENR register
6 0
5 - not used
4 0 Select pen
3 x Pen number
2 x
1 x
0 x


Register INKR (Change the value of the currently selected color register)

Once the pen has been selected its colour can then be changed. Bits 4 to 0 specify the hardware colour number from the hardware colour palette.

Even though there is provision for 32 colours, only 27 are possible. The remaining colours are duplicates of those already in the colour palette.

Summary

Bit Value Function
7 0 Gate Array INKR register
6 1
5 - not used
4 x Colour number x
3 x
2 x
1 x
0 x


Register RMR (Control Interrupt counter, ROM mapping and Graphics mode)

This is a general purpose register responsible for the graphics mode and the ROM configuration.

Graphics mode selection

The function of bits 1 and 0 is to define the screen mode. The settings for bits 1 and 0 and the corresponding screen mode are given in the table below.

Bit 1 Bit 0 Screen mode
0 0 Mode 0, 160x200 resolution, 16 colours
0 1 Mode 1, 320x200 resolution, 4 colours
1 0 Mode 2, 640x200 resolution, 2 colours
1 1 Mode 3, 160x200 resolution, 4 colours (undocumented)
  • Mode 3 is not official. From the combinations possible, we can see that 4 modes can be defined, although the Amstrad only has 3. Mode 3 is similar to mode 0, because it has the same resolution, but it is limited to only 4 colours. Mode 3 is not supported by the KC Compact (which outputs black in Mode 3).

Mode changing is synchronised with HSYNC. If the mode is changed, it will take effect from the next HSYNC.

ROM configuration selection

Bit 2 is used to enable or disable the lower ROM area. The lower ROM area occupies memory addresses &0000-&3fff and is used to access the operating system ROM. When the lower ROM area is is enabled, reading from &0000-&3FFF will return data in the ROM. When a value is written to &0000-&3FFF, it will be written to the RAM underneath the RAM. When it is disabled, data read from &0000-&3FFF will return the data in the RAM.

Similarly, bit 3 controls enabling or disabling of the upper ROM area. The upper ROM area occupies memory addressess &C000-&FFFF and is BASIC or any expansion ROMs which may be plugged into a ROM board/box. See the document on upper rom selection for more details. When the upper ROM area enabled, reading from &c000-&ffff, will return data in the ROM. When data is written to &c000-&FFFF, it will be written to the RAM at the same address as the ROM. When the upper ROM area is disabled, and data is read from &c000-&ffff it will be the data in the RAM.

Bit 4 controls the interrupt generation. It can be used to delay interrupts. See the document on interrupt generation for more information.

Summary

Bit Value Function
7 1 Gate Array RMR register
6 0
5 - must be 0 on Plus machines with ASIC unlocked
4 x Interrupt generation control
3 x 1=Upper ROM area disable, 0=Upper ROM area enable
2 x 1=Lower ROM area disable, 0=Lower ROM area enable
1 x Graphics Mode selection
0 x


Register RMR2 (ASIC & Advanced ROM mapping)

This register exists only in Plus or GX4000, and is only accessible when the ASIC is unlocked.

Bit Value Function
7 1 Gate Array RMR2 register
6 0
5 1
4 x Lower ROM address and ASIC I/O page mode
3 x
2 x Physical ROM number (0..7)
1 x
0 x

The lower ROM address and ASIC I/O page modes are: 

 -Mode-   ROM address    ASIC I/O Page
   00     &0000-&3FFF      Disabled
   01     &4000-&7FFF      Disabled
   10     &8000-&BFFF      Disabled
   11     &0000-&3FFF     &4000-&7fff

The physical ROMs are also accessible as upper ROMs by using the Upper ROM Bank Number port and the RMR register.


Register MMR (RAM memory mapping)

This register exists only in CPCs with 128K RAM (like the CPC 6128, or CPCs with Standard Memory Expansions). Note: In the CPC 6128, the register is a separate PAL chip that assists the Gate Array chip. See its wiki page.

Bit Value Function
7 1 Gate Array MMR register
6 1
5 x 64K bank number (0..7); always 0 on an unexpanded CPC6128, 0-7 on Standard Memory Expansions
4 x
3 x
2 x RAM Config (0..7)
1 x
0 x


The 3bit RAM Config value is used to access the second 64K of the total 128K RAM that is built into the CPC 6128 or the additional 64K-512K of standard memory expansions. These contain up to eight 64K ram banks, which are selected with bit 3-5. A standard CPC 6128 only contains bank 0. Normally the register is set to 0, so that only the first 64K RAM are used (identical to the CPC 464 and 664 models). The register can be used to select between the following eight predefined configurations only: 

 -Address-     0      1      2      3      4      5      6      7
 0000-3FFF   RAM_0  RAM_0  RAM_4  RAM_0  RAM_0  RAM_0  RAM_0  RAM_0
 4000-7FFF   RAM_1  RAM_1  RAM_5  RAM_3  RAM_4  RAM_5  RAM_6  RAM_7
 8000-BFFF   RAM_2  RAM_2  RAM_6  RAM_2  RAM_2  RAM_2  RAM_2  RAM_2
 C000-FFFF   RAM_3  RAM_7  RAM_7  RAM_7  RAM_3  RAM_3  RAM_3  RAM_3

The Video RAM is always located in the first 64K, VRAM is in no way affected by this register.


Programming the Gate Array - Examples

Defining the colours,
Setting pen 0 to Bright White. 

LD BC,7F00 ;Gate Array port
LD A,%00000000+0 ;Pen number (and Gate Array function)
OUT (C),A ;Send pen number
LD A,%01000000+11 ;Pen colour (and Gate Array function)
OUT (C),A ;Send it
RET

Setting the mode and ROM configuration, 
Mode 2, upper and lower ROM disabled.

LD BC,7F00 ;Gate array port
LD A,%10000000+%00001110 ;Mode and ROM selection (and Gate Array function)
OUT (C),A ;Send it
RET

Misc

The hardware colour number is different to the colour range used by the firmware, so a conversion chart is provided for the corresponding firmware/hardware colour values and the corresponding colour name.

Note

The firmware keeps track of the colours it is using. Every VSYNC (assuming interrupts are enabled) the firmware sets the colours. This enables the user to have flashing colours. If the user selects a new colour using the gate array, the new colour will flash temporarily and then return to its original colour. This is due to the firmware resetting the colour. When using the firmware, use its routines to select the colour, and the colour will remain.

Example: [For whatever reason, this example does NOT refer to the above firmware stuff] 

ld bc,7f00+1 ;Gate array function (set pen)
;and pen number
out (c),c
ld bc,7f00 ;41 
;Gate array function (set colour)
;and colour number
out (c),c
ret


Video memory structure

Graphics Mode VRAM byte Displayed Pixels Definition
7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8
0 A0 B0 A2 B2 A1 B1 A3 B3 A B 2 pixels in 16 colors
1 A0 B0 C0 D0 A1 B1 C1 D1 A B C D 4 pixels in 4 colours
2 A0 B0 C0 D0 E0 F0 G0 H0 A B C D E F G H 8 pixels in 2 colors
3 A0 B0 x x A1 B1 x x A B 2 pixels in 4 colors


Split rasters

On the CPC, split rasters occur halfway (after the 8th mode2 pixel) through the rendering of a CRTC character.

On Amstrad Plus, split rasters occur quarter of the way (after the 4th mode2 pixel) through the rendering of a CRTC character.

To easily make split rasters compatible with both the CPC and the Plus machines, one can use the ASIC soft-scroll control register (SSCR) to finely adjust the horizontal position of the graphics.


Palette R,G,B definitions

There are 27 colours which are generated from red, green and blue mixed in different quantities. There are 3 levels of red, 3 levels of green and 3 levels of blue, and these can be thought of as off/no colour, half-on/half-colour, and on/full-colour.

To display a CPC image you will need to use a analogue monitor with a composite sync.


Palette sorted by Hardware Colour Numbers

Hardware Number Firmware Number Colour Name R % G % B % ASIC Colour
0 (40h) 13 White 50 50 50 #666
1 (41h) (13) White 50 50 50 #666
2 (42h) 19 Sea Green 0 100 50 #0F6
3 (43h) 25 Pastel Yellow 100 100 50 #FF6
4 (44h) 1 Blue 0 0 50 #006
5 (45h) 7 Purple 100 0 50 #F06
6 (46h) 10 Cyan 0 50 50 #066
7 (47h) 16 Pink 100 50 50 #F66
8 (48h) (7) Purple 100 0 50 #F06
9 (49h) (25) Pastel Yellow 100 100 50 #FF6
10 (4Ah) 24 Bright Yellow 100 100 0 #FF0
11 (4Bh) 26 Bright White 100 100 100 #FFF
12 (4Ch) 6 Bright Red 100 0 0 #F00
13 (4Dh) 8 Bright Magenta 100 0 100 #F0F
14 (4Eh) 15 Orange 100 50 0 #F60
15 (4Fh) 17 Pastel Magenta 100 50 100 #F6F
16 (50h) (1) Blue 0 0 50 #006
17 (51h) (19) Sea Green 0 100 50 #0F6
18 (52h) 18 Bright Green 0 100 0 #0F0
19 (53h) 20 Bright Cyan 0 100 100 #0FF
20 (54h) 0 Black 0 0 0 #000
21 (55h) 2 Bright Blue 0 0 100 #00F
22 (56h) 9 Green 0 50 0 #060
23 (57h) 11 Sky Blue 0 50 100 #06F
24 (58h) 4 Magenta 50 0 50 #606
25 (59h) 22 Pastel Green 50 100 50 #6F6
26 (5Ah) 21 Lime 50 100 0 #6F0
27 (5Bh) 23 Pastel Cyan 50 100 100 #6FF
28 (5Ch) 3 Red 50 0 0 #600
29 (5Dh) 5 Mauve 50 0 100 #60F
30 (5Eh) 12 Yellow 50 50 0 #660
31 (5Fh) 14 Pastel Blue 50 50 100 #66F


Palette sorted by Firmware Colour Numbers

Firmware Number Hardware Number Colour Name R % G % B % ASIC Colour
0 54h Black 0 0 0 #000
1 44h (or 50h) Blue 0 0 50 #006
2 55h Bright Blue 0 0 100 #00F
3 5Ch Red 50 0 0 #600
4 58h Magenta 50 0 50 #606
5 5Dh Mauve 50 0 100 #60F
6 4Ch Bright Red 100 0 0 #F00
7 45h (or 48h) Purple 100 0 50 #F06
8 4Dh Bright Magenta 100 0 100 #F0F
9 56h Green 0 50 0 #060
10 46h Cyan 0 50 50 #066
11 57h Sky Blue 0 50 100 #06F
12 5Eh Yellow 50 50 0 #660
13 40h (or 41h) White 50 50 50 #666
14 5Fh Pastel Blue 50 50 100 #66F
15 4Eh Orange 100 50 0 #F60
16 47h Pink 100 50 50 #F66
17 4Fh Pastel Magenta 100 50 100 #F6F
18 52h Bright Green 0 100 0 #0F0
19 42h (or 51h) Sea Green 0 100 50 #0F6
20 53h Bright Cyan 0 100 100 #0FF
21 5Ah Lime 50 100 0 #6F0
22 59h Pastel Green 50 100 50 #6F6
23 5Bh Pastel Cyan 50 100 100 #6FF
24 4Ah Bright Yellow 100 100 0 #FF0
25 43h (or 49h) Pastel Yellow 100 100 50 #FF6
26 4Bh Bright White 100 100 100 #FFF


Intensities

The 0%, 50%, and 100% values in the above tables are "should-be" values. However, the real hardware doesn't exactly match that intensities. The actual intensities depend on the luminance mixing (R,G,B tied together via resistors), on chipset (classic CPC, or newer ASIC ones), and on the load applied by external hardware (Monitor, or TV set).

On an actual Amstrad CPC, the half-intensity colour signal is measured to be closer to 40% rather than the expected 50%. This was verified by Grim and independently confirmed by Nocash. Source

This explains why the Amstrad engineers used these values to adapt the old colour palette to the new 12-bit palette on the Amstrad Plus:

  • 0% became #0
  • 50% became #6
  • 100% became #F

They specifically chose #6 for the 50% value instead of #7, to better match the real Amstrad CPC palette.


Green Screen Colours

On a green screen (where all colours are shades of unsaturated green), the colours (in BASIC colours) are in order of increasing intensity. Black is very dark, and white is bright green, and colour 13 is a medium green. (Thanks to Mark Rison for this information)

The luminance (Y) is not exactly correlated to the actual luminance of colour images broadcast in RGB. We have other values.

Amstrad preferred to propose a completely different image system, not comparable to a conversion to monochrome, which would have limited the number of brightness levels to 21 (for example, colours 9 and 6 would have had the same luminance).

They opted for a table of 27 linear brightness steps. They assigned values of 1 (1kΩ) for blue, 3 (3.3kΩ) for red, and 9 (10kΩ) for green.


To calculate the luminance value

Red

0% => do not add anything

50% => add 3

100% => add 6

Green

0% => do not add anything

50% => add 9

100% => add 18

Blue

0% => do not add anything

50% => add 1

100% => add 2


Pictures

  • 40010 GA Metal Layer

  • 40010 GA with Metal Layer removed

  • 40226 PreASIC Metal Layer

Ga.pinout.40007.png Ga.pinout.40008.40010.png

Note: Some CPC motherboards can accommodate both types of Gate Array pinouts. Source


External links


See also

  • Video modes : for other informations on colours and pixels.
Retrieved from "https://gryzor.info/index.php?title=Gate_Array&oldid=120147"