Difference between revisions of "Schneiderware Uni-PIO"
(Created page with "The Schneiderware Uni-PIO is a general purpose I/O port with 48 input/output signals, published by german magazine CPC Schneider International as part of their [[Schneide...") |
|||
| (3 intermediate revisions by one other user not shown) | |||
| Line 37: | Line 37: | ||
File:Schneiderware 6 Uni-PIO (solder side).jpg|Uni-PIO (solder side) | File:Schneiderware 6 Uni-PIO (solder side).jpg|Uni-PIO (solder side) | ||
</gallery> | </gallery> | ||
| + | |||
| + | == Scanned Article == | ||
| + | |||
| + | * [[Media:Schneiderware 6 - Uni-PIO.pdf|Schneiderware 6 - Uni-PIO.pdf]] - 48 I/O lines - '''12/1986 page 124-130''', advert on 1/1987 page 144, correction on 5/1987 page 12, final notes from 11/1987 page 99 | ||
| + | |||
| + | [[Category:Peripherals]] | ||
Latest revision as of 02:20, 29 August 2014
The Schneiderware Uni-PIO is a general purpose I/O port with 48 input/output signals, published by german magazine CPC Schneider International as part of their Schneiderware DIY series. The plain PCB, or the fully assembled board were also available via mail-order.
The ECB Bus connector of the board is intended to be plugged into the Schneiderware Basisplatine, but it could be also wired directly to the CPCs Expansion Port.
I/O Ports
Default I/O Addresses are F8E8h-F8EFh, optionally a second or third Uni-PIO card can be jumpered to F8F0h-F8F7h and F8F8h-F8F8h, giving a total of 144 I/O lines when using three cards.
| Address (default) | Address (alternate) | Usage |
| F8E8h | F8F0h,F8F8h | Schneiderware Uni-PIO 8255 PPI chip #1 Port A (without pull-ups, with red LEDs) |
| F8E9h | F8F1h,F8F9h | Schneiderware Uni-PIO 8255 PPI chip #1 Port B (with pull-ups and green LEDs) |
| F8EAh | F8F2h,F8FAh | Schneiderware Uni-PIO 8255 PPI chip #1 Port C (lower 4bit without pull-ups and red LEDs, upper 4bit with pull-ups and green LEDs) |
| F8EBh | F8F3h,F8FBh | Schneiderware Uni-PIO 8255 PPI chip #1 Control |
| F8ECh | F8F4h,F8FCh | Schneiderware Uni-PIO 8255 PPI chip #2 Port A (without pull-ups or LEDs) |
| F8EDh | F8F5h,F8FDh | Schneiderware Uni-PIO 8255 PPI chip #2 Port B (without pull-ups or LEDs) |
| F8EEh | F8F6h,F8FEh | Schneiderware Uni-PIO 8255 PPI chip #2 Port C (without pull-ups or LEDs) |
| F8EFh | F8F7h,F8FFh | Schneiderware Uni-PIO 8255 PPI chip #2 Control |
Cautions - Port F8F0h-F8F3h were also used as alternate address of the Schneiderware Centronics Port, recommended work-around is to modify the Centronics card. On the PCBs, two PPI #1 Port C signals are accidently exchanged with each other (wired to the wrong pins on the 50-pin connector, and to the wrong LEDs).
Pictures
Uni-PIO Schematic
Uni-PIO (component side)
Uni-PIO (solder side)
.jpg)
.jpg)
Scanned Article
- Schneiderware 6 - Uni-PIO.pdf - 48 I/O lines - 12/1986 page 124-130, advert on 1/1987 page 144, correction on 5/1987 page 12, final notes from 11/1987 page 99
