Difference between revisions of "Amstrad External Disk Drive"
(→Manuals) |
|||
Line 53: | Line 53: | ||
* [http://www.cpcwiki.eu/manuals/ddi-1.zip Amstrad DDI-1 (English) Manual] | * [http://www.cpcwiki.eu/manuals/ddi-1.zip Amstrad DDI-1 (English) Manual] | ||
* [http://www.cpcwiki.eu/manuals/DDI-1.es.rar Amstrad DDI-1 (Spanish) Manual] | * [http://www.cpcwiki.eu/manuals/DDI-1.es.rar Amstrad DDI-1 (Spanish) Manual] | ||
+ | * [[Media:DDI-1_Handbuch.pdf]] (German) Manual | ||
== Service Manual == | == Service Manual == |
Revision as of 03:39, 26 August 2010
Amstrad made two different disk drives for the Amstrad/Schneider CPC range:
- DDI-1: a set consisting of the real DDI-1 (= Disk Drive Interface) and a FD-1 3" disk drive, as well as the CP/M 2.2 license and disk.
This set was for the CPC464 which didn't have a built-in 765 FDC disk controller.
- FD-1: a 3" disk drive as secondary disk drive unit for the CPC664, CPC6128, and for the CPC464 with DDI-1
All drives are for use with CF2 Compact Floppy Disc 3" discs.
There was no official external disk drive for the 6128Plus or even the 464Plus. The difference between a CPC664/CPC6128 and a 6128Plus was simply a changed pin-out which can easily be solved by a new plug on the disk drive's cable.
The 464Plus was harder to equip with a disk drive. Although the pin-out of the expansion port was left unchanged, the DDI-1 cannot be used on the 464Plus without modifications (see Connecting a Disc Interface to CPC464+).
Technical Details
The two disk drives were identical. The only difference was that the DDI-1 shipped with controller, manual and CP/M 2.2 on one disk.
The disk drives were jumpered (more accurately, soldered) to react on both drive select lines, A: and B:.
The cable decided which drive became A: and which one became B: :
- On the CPC664 and CPC6128 computers, DRIVE SELECT 0 was not connected on the external connector, so the drive could only become drive B: on these systems.
- For the DDI-1, DRIVE SELECT 0 was only wired to the outermost connector of the attached cable, while the inner connector was wired to DRIVE SELECT 1 only, thus the drive at the cable's end always became A: while the other one became drive B: accordingly.
Note that the drive also powered the DDI-1 interface when used together with it. Certain pins documented as N/C in the CPC664/CPC6128 manual in fact carry +5V from the drive to the controller. The main reason for this was that you couldn't connect a standard drive with a more common format (5¼" in the beginning, 3½" later and today) and thus cheaper disks as drive A: without modifications, as the DDI-1 wouldn't work without the power fed from the FD-1.
Pictures
Covers
Manuals
- Amstrad DDI-1 (English) Manual
- Amstrad DDI-1 (Spanish) Manual
- Media:DDI-1_Handbuch.pdf (German) Manual
Service Manual
Datasheets
- Media:UPD765 Datasheet OCRed.pdf - uPD765 disc controller
- Media:FDC9229BT Datasheet.pdf - FDC9229BT data separator (that usually assists the uPD765 chip)
- Media:DDI Schematic.png - DDI-1 Schematic (disc interface for CPC464)