Difference between revisions of "765 FDC"

From CPCWiki - THE Amstrad CPC encyclopedia!
Jump to: navigation, search
(→‎Custom floppy disk formats)
 
(384 intermediate revisions by 2 users not shown)
Line 3: Line 3:
 
The ports used by Amstrad and compatible interfaces use:
 
The ports used by Amstrad and compatible interfaces use:
  
−
* Port FA7Eh - Floppy Motor On/Off Flipflop
+
* Port &FA7E - Floppy Motor On/Off Flipflop
−
* Port FB7Eh - FDC 765 Main Status Register (read only)
+
* Port &FB7E - FDC 765 Main Status Register (read only)
−
* Port FB7Fh - FDC 765 Data Register (read/write)
+
* Port &FB7F - FDC 765 Data Register (read/write)
  
 
The [[Vortex Disc Drives|Vortex disc interface]] uses other ports. See its dedicated wiki page.
 
The [[Vortex Disc Drives|Vortex disc interface]] uses other ports. See its dedicated wiki page.
 +
 +
<br>
  
 
== IC Models used in CPC ==
 
== IC Models used in CPC ==
Line 15: Line 17:
 
All should operate almost identically.
 
All should operate almost identically.
  
−
* [[Zilog]] Z0765A08PSC
+
* NEC D765AC [https://www.cpcwiki.eu/imgs/3/3c/CPC664_Z70205_MC0005B_PCB_Top.jpg Source]
−
* [[NEC D765AC-2]]
+
* NEC D765AC-2 [https://www.cpcwiki.eu/imgs/4/45/CPC6128_PCB_Top_%28Z70210_MC0009A%29.jpg Source]
−
* NEC D765AC
+
* UMC UM8272A [[Media:Amstrad cpc 6128 azerty (f) placa2.jpg|Source]]
−
* UMC UM8272A
+
* Zilog Z765APS [https://www.cpcwiki.eu/imgs/f/fb/CPC6128_Z70290_MC0020C_PCB_Top.jpg Source]
 +
* [[Zilog]] Z0765A08PSC [https://www.cpcwiki.eu/imgs/6/67/CPC6128_PCB_Top_%28Z70290_MC0020F%29.jpg Source]
  
 
The following data seperators are used:
 
The following data seperators are used:
  
−
* FDC9216
+
* FDC9216 [https://www.cpcwiki.eu/imgs/4/45/CPC6128_PCB_Top_%28Z70210_MC0009A%29.jpg Source]
−
* SED9420C
+
* SED9420C [https://www.cpcwiki.eu/imgs/3/3c/CPC6128_PCB_Top_%28Z70290_MC0020A%29.jpg Source]
  
−
Note: The CPC464, CPC472, 464 Plus and GX4000 are not equipped with a FDC chip.
+
The CPC464, CPC472, 464 Plus and GX4000 are not equipped with a FDC chip.
 +
 
 +
All the floppy disk drive models used by Amstrad are referenced here: [https://www.cpcwiki.eu/index.php/Amstrad_FDD_part Amstrad FDD part]
 +
 
 +
<br>
  
 
== Accessing the FDC 765 ==
 
== Accessing the FDC 765 ==
−
The Data Register (Port FB7Fh) is used to write Commands and Parameters, to read/write data bytes, and to receive result bytes. These three operations are called Command-, Execution-, and Result-Phase. The Main Status Register signalizes when the FDC is ready to send/receive the next byte through the Data Register.
 
  
−
a. Command Phase
+
The Main Status Register (Port &FB7E) signalizes when the FDC is ready to send/receive the next byte through the Data Register.
  
−
A command consists of a command byte (eventually including the MF, MK, SK bits), and up to eight parameter bytes.
+
The Data Register (Port &FB7F) is used to write Commands and Parameters, to read/write data bytes, and to receive result bytes. These 3 operations are called Command-, Execution-, and Result-Phase.
  
−
b. Execution Phase
+
<br>
  
−
During this phase, the actual data is transferred (if any). Usually that are the data bytes for the read/written sector(s), except for the Format Track Command, in that case four bytes for each sector are transferred.
+
=== Command Phase ===
  
−
c. Result Phase
+
A command consists of a command byte (eventually including the MT, MF, SK bits), and up to 8 parameter bytes.
  
−
Returns up to seven result bytes (depending on the command) that are containing status information. The Recalibrate and Seek Track commands do not return result bytes directly, instead the program must wait until the Main Status Register signalizes that the command has been completed, and then it must (!) send a Sense Interrupt State command to 'terminate' the Seek/Recalibrate command.
+
<br>
  
−
== FDC Command Table ==
+
=== Execution Phase ===
  
−
Command    Parameters              Exm Result              Description
+
During this phase, the actual data is transferred (if any). Usually that are the data bytes for the read/written sector(s), except for the Format Track Command, in that case 4 bytes for each sector are transferred.
−
02+MF+SK    HU TR HD ?? SZ NM GP SL <R> S0 S1 S2 TR HD NM SZ read track
+
−
03          XX YY                    -                      specify spd/dma
+
−
04          HU                      -  S3                  sense drive state
+
−
05+MT+MF    HU TR HD SC SZ LS GP SL <W> S0 S1 S2 TR HD LS SZ write sector(s)
+
−
06+MT+MF+SK HU TR HD SC SZ LS GP SL <R> S0 S1 S2 TR HD LS SZ read sector(s)
+
−
07          HU                      -                      recalib.seek TP=0
+
−
08          -                        -  S0 TP                sense int.state
+
−
09+MT+MF    HU TR HD SC SZ LS GP SL <W> S0 S1 S2 TR HD LS SZ wr deleted sec(s)
+
−
0A+MF      HU                      -  S0 S1 S2 TR HD LS SZ read ID
+
−
0C+MT+MF+SK HU TR HD SC SZ LS GP SL <R> S0 S1 S2 TR HD LS SZ rd deleted sec(s)
+
−
0D+MF      HU SZ NM GP FB          <W> S0 S1 S2 TR HD LS SZ format track
+
−
0F          HU TP                    -                      seek track n
+
−
11+MT+MF+SK HU TR HD SC SZ LS GP SL <W> S0 S1 S2 TR HD LS SZ scan equal
+
−
19+MT+MF+SK HU TR HD SC SZ LS GP SL <W> S0 S1 S2 TR HD LS SZ scan low or equal
+
−
1D+MT+MF+SK HU TR HD SC SZ LS GP SL <W> S0 S1 S2 TR HD LS SZ scan high or eq.
+
  
−
Parameter bits that can be specified in some Command Bytes are:
+
During data transfers between the FDC and the processor, the FDC must be serviced every 26µs (for MFM mode with CPC timings) or the FDC terminates the FDC command.
  
−
  MT  Bit7  Multi Track (continue multi-sector-function on other head)
+
<br>
−
  MF  Bit6  MFM-Mode-Bit (Default 1=Double Density)
+
−
  SK  Bit5  Skip-Bit (set if secs with deleted DAM shall be skipped)
+
  
−
Parameter/Result bytes are:
+
=== Result Phase ===
  
−
  HU  b0,1=Unit/Drive Number, b2=Physical Head Number, other bits zero
+
Returns up to 7 result bytes (depending on the command) that are containing status information. The Recalibrate and Seek Track commands do not return result bytes directly, instead the program must wait until the Main Status Register signalizes that the command has been completed, and then it must (!) send a Sense Interrupt State command to 'terminate' the Seek/Recalibrate command.
−
  TP  Physical Track Number
+
−
  TR  Track-ID (usually same value as TP)
+
−
  HD  Head-ID
+
−
  SC  First Sector-ID (sector you want to read)
+
−
  SZ  Sector Size (80h shl n) (default=02h for 200h bytes)
+
−
  LS  Last Sector-ID (should be same as SC when reading a single sector)
+
−
  GP  Gap (default=2Ah except command 0D: default=52h)
+
−
  SL  Sectorlen if SZ=0 (default=FFh)
+
−
  Sn  Status Register 0..3
+
−
  FB  Fillbyte (for the sector data areas) (default=E5h)
+
−
  NM  Number of Sectors (default=09h)
+
−
  XX  b0..3=headunload n*32ms (8" only), b4..7=steprate (16-n)*2ms
+
−
  YY  b0=DMA_disable, b1-7=headload n*4ms (8" only)
+
  
−
Format Track: output TR,HD,SC,SZ for each sector during execution phase
+
During the result phase, all the result bytes must be read. The FDC will not accept a new command until all the result bytes are read.
−
Read Track: reads NM sectors (starting with first sec past index hole)
+
 
−
Read ID: read ID bytes for current sec, repeated/undelayed read lists all IDs
+
<br>
−
Recalib: walks up to 77 tracks, 80tr-drives may need second recalib if failed
+
 
−
Seek/Recalib: All read/write commands will be disabled until succesful senseint
+
== The 15 FDC Commands ==
−
Senseint: Set's IC if unsuccesful (no int has occured) (until IC=0)
+
 
 +
{|
 +
|
 +
{| class="wikitable"
 +
|+ Scan Equal (11h)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || MT || MF || SK || 1 || 0 || 0 || 0 || 1
 +
|-
 +
| command byte 1 || colspan="5" style="text-align: center;" | x || HD || colspan="2" style="text-align: center;" | US
 +
|-
 +
| command byte 2 || colspan="8" | C: cylinder number
 +
|-
 +
| command byte 3 || colspan="8" | H: head number
 +
|-
 +
| command byte 4 || colspan="8" | R: sector number
 +
|-
 +
| command byte 5 || colspan="8" | N: bytes per sector
 +
|-
 +
| command byte 6 || colspan="8" | EOT: end of track (ie. last sector in track)
 +
|-
 +
| command byte 7 || colspan="8" | GPL: gap 3 length
 +
|-
 +
| command byte 8 || colspan="8" | STP: scan test (1=scan contiguous, 2=scan alternate)
 +
|-
 +
| Execution      || colspan="8" | Data compared between the FDD and main-system
 +
|-
 +
| result byte 0  || colspan="8" | ST0: status register 0
 +
|-
 +
| result byte 1  || colspan="8" | ST1: status register 1
 +
|-
 +
| result byte 2  || colspan="8" | ST2: status register 2
 +
|-
 +
| result byte 3  || colspan="8" | C: cylinder number
 +
|-
 +
| result byte 4  || colspan="8" | H: head number
 +
|-
 +
| result byte 5  || colspan="8" | R: sector number
 +
|-
 +
| result byte 6  || colspan="8" | N: bytes per sector
 +
|}
 +
|
 +
{| class="wikitable"
 +
|+ Scan Low or Equal (19h)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || MT || MF || SK || 1 || 1 || 0 || 0 || 1
 +
|-
 +
| command byte 1 || colspan="5" style="text-align: center;" | x || HD || colspan="2" style="text-align: center;" | US
 +
|-
 +
| command byte 2 || colspan="8" | C: cylinder number
 +
|-
 +
| command byte 3 || colspan="8" | H: head number
 +
|-
 +
| command byte 4 || colspan="8" | R: sector number
 +
|-
 +
| command byte 5 || colspan="8" | N: bytes per sector
 +
|-
 +
| command byte 6 || colspan="8" | EOT: end of track (ie. last sector in track)
 +
|-
 +
| command byte 7 || colspan="8" | GPL: gap 3 length
 +
|-
 +
| command byte 8 || colspan="8" | STP: scan test (1=scan contiguous, 2=scan alternate)
 +
|-
 +
| Execution      || colspan="8" | Data compared between the FDD and main-system
 +
|-
 +
| result byte 0  || colspan="8" | ST0: status register 0
 +
|-
 +
| result byte 1  || colspan="8" | ST1: status register 1
 +
|-
 +
| result byte 2  || colspan="8" | ST2: status register 2
 +
|-
 +
| result byte 3  || colspan="8" | C: cylinder number
 +
|-
 +
| result byte 4  || colspan="8" | H: head number
 +
|-
 +
| result byte 5  || colspan="8" | R: sector number
 +
|-
 +
| result byte 6  || colspan="8" | N: bytes per sector
 +
|}
 +
|
 +
{| class="wikitable"
 +
|+ Scan High or Equal (1Dh)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || MT || MF || SK || 1 || 1 || 1 || 0 || 1
 +
|-
 +
| command byte 1 || colspan="5" style="text-align: center;" | x || HD || colspan="2" style="text-align: center;" | US
 +
|-
 +
| command byte 2 || colspan="8" | C: cylinder number
 +
|-
 +
| command byte 3 || colspan="8" | H: head number
 +
|-
 +
| command byte 4 || colspan="8" | R: sector number
 +
|-
 +
| command byte 5 || colspan="8" | N: bytes per sector
 +
|-
 +
| command byte 6 || colspan="8" | EOT: end of track (ie. last sector in track)
 +
|-
 +
| command byte 7 || colspan="8" | GPL: gap 3 length
 +
|-
 +
| command byte 8 || colspan="8" | STP: scan test (1=scan contiguous, 2=scan alternate)
 +
|-
 +
| Execution      || colspan="8" | Data compared between the FDD and main-system
 +
|-
 +
| result byte 0  || colspan="8" | ST0: status register 0
 +
|-
 +
| result byte 1  || colspan="8" | ST1: status register 1
 +
|-
 +
| result byte 2  || colspan="8" | ST2: status register 2
 +
|-
 +
| result byte 3  || colspan="8" | C: cylinder number
 +
|-
 +
| result byte 4  || colspan="8" | H: head number
 +
|-
 +
| result byte 5  || colspan="8" | R: sector number
 +
|-
 +
| result byte 6  || colspan="8" | N: bytes per sector
 +
|}
 +
|}
 +
 
 +
{|
 +
|
 +
{| class="wikitable"
 +
|+ Read Data (06h)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || MT || MF || SK || 0 || 0 || 1 || 1 || 0
 +
|-
 +
| command byte 1 || colspan="5" style="text-align: center;" | x || HD || colspan="2" style="text-align: center;" | US
 +
|-
 +
| command byte 2 || colspan="8" | C: cylinder number
 +
|-
 +
| command byte 3 || colspan="8" | H: head number
 +
|-
 +
| command byte 4 || colspan="8" | R: sector number
 +
|-
 +
| command byte 5 || colspan="8" | N: bytes per sector
 +
|-
 +
| command byte 6 || colspan="8" | EOT: end of track (ie. last sector in track)
 +
|-
 +
| command byte 7 || colspan="8" | GPL: gap 3 length
 +
|-
 +
| command byte 8 || colspan="8" | DTL: data length (if command byte 5==0)
 +
|-
 +
| Execution      || colspan="8" | Data-transfer from the FDD
 +
|-
 +
| result byte 0  || colspan="8" | ST0: status register 0
 +
|-
 +
| result byte 1  || colspan="8" | ST1: status register 1
 +
|-
 +
| result byte 2  || colspan="8" | ST2: status register 2
 +
|-
 +
| result byte 3  || colspan="8" | C: cylinder number
 +
|-
 +
| result byte 4  || colspan="8" | H: head number
 +
|-
 +
| result byte 5  || colspan="8" | R: sector number
 +
|-
 +
| result byte 6  || colspan="8" | N: bytes per sector
 +
|}
 +
|
 +
{| class="wikitable"
 +
|+ Read Deleted Data (0Ch)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || MT || MF || SK || 0 || 1 || 1 || 0 || 0
 +
|-
 +
| command byte 1 || colspan="5" style="text-align: center;" | x || HD || colspan="2" style="text-align: center;" | US
 +
|-
 +
| command byte 2 || colspan="8" | C: cylinder number
 +
|-
 +
| command byte 3 || colspan="8" | H: head number
 +
|-
 +
| command byte 4 || colspan="8" | R: sector number
 +
|-
 +
| command byte 5 || colspan="8" | N: bytes per sector
 +
|-
 +
| command byte 6 || colspan="8" | EOT: end of track (ie. last sector in track)
 +
|-
 +
| command byte 7 || colspan="8" | GPL: gap 3 length
 +
|-
 +
| command byte 8 || colspan="8" | DTL: data length (if command byte 5==0)
 +
|-
 +
| Execution      || colspan="8" | Data-transfer from the FDD
 +
|-
 +
| result byte 0  || colspan="8" | ST0: status register 0
 +
|-
 +
| result byte 1  || colspan="8" | ST1: status register 1
 +
|-
 +
| result byte 2  || colspan="8" | ST2: status register 2
 +
|-
 +
| result byte 3  || colspan="8" | C: cylinder number
 +
|-
 +
| result byte 4  || colspan="8" | H: head number
 +
|-
 +
| result byte 5  || colspan="8" | R: sector number
 +
|-
 +
| result byte 6  || colspan="8" | N: bytes per sector
 +
|}
 +
|
 +
{| class="wikitable"
 +
|+ Write Data (05h)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || MT || MF || x || 0 || 0 || 1 || 0 || 1
 +
|-
 +
| command byte 1 || colspan="5" style="text-align: center;" | x || HD || colspan="2" style="text-align: center;" | US
 +
|-
 +
| command byte 2 || colspan="8" | C: cylinder number
 +
|-
 +
| command byte 3 || colspan="8" | H: head number
 +
|-
 +
| command byte 4 || colspan="8" | R: sector number
 +
|-
 +
| command byte 5 || colspan="8" | N: bytes per sector
 +
|-
 +
| command byte 6 || colspan="8" | EOT: end of track (ie. last sector in track)
 +
|-
 +
| command byte 7 || colspan="8" | GPL: gap 3 length
 +
|-
 +
| command byte 8 || colspan="8" | DTL: data length (if command byte 5==0)
 +
|-
 +
| Execution      || colspan="8" | Data-transfer to the FDD
 +
|-
 +
| result byte 0  || colspan="8" | ST0: status register 0
 +
|-
 +
| result byte 1  || colspan="8" | ST1: status register 1
 +
|-
 +
| result byte 2  || colspan="8" | ST2: status register 2
 +
|-
 +
| result byte 3  || colspan="8" | C: cylinder number
 +
|-
 +
| result byte 4  || colspan="8" | H: head number
 +
|-
 +
| result byte 5  || colspan="8" | R: sector number
 +
|-
 +
| result byte 6  || colspan="8" | N: bytes per sector
 +
|}
 +
|
 +
{| class="wikitable"
 +
|+ Write Deleted Data (09h)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || MT || MF || x || 0 || 1 || 0 || 0 || 1
 +
|-
 +
| command byte 1 || colspan="5" style="text-align: center;" | x || HD || colspan="2" style="text-align: center;" | US
 +
|-
 +
| command byte 2 || colspan="8" | C: cylinder number
 +
|-
 +
| command byte 3 || colspan="8" | H: head number
 +
|-
 +
| command byte 4 || colspan="8" | R: sector number
 +
|-
 +
| command byte 5 || colspan="8" | N: bytes per sector
 +
|-
 +
| command byte 6 || colspan="8" | EOT: end of track (ie. last sector in track)
 +
|-
 +
| command byte 7 || colspan="8" | GPL: gap 3 length
 +
|-
 +
| command byte 8 || colspan="8" | DTL: data length (if command byte 5==0)
 +
|-
 +
| Execution      || colspan="8" | Data-transfer to the FDD
 +
|-
 +
| result byte 0  || colspan="8" | ST0: status register 0
 +
|-
 +
| result byte 1  || colspan="8" | ST1: status register 1
 +
|-
 +
| result byte 2  || colspan="8" | ST2: status register 2
 +
|-
 +
| result byte 3  || colspan="8" | C: cylinder number
 +
|-
 +
| result byte 4  || colspan="8" | H: head number
 +
|-
 +
| result byte 5  || colspan="8" | R: sector number
 +
|-
 +
| result byte 6  || colspan="8" | N: bytes per sector
 +
|}
 +
|}
 +
 
 +
{| class="wikitable"
 +
|+ Read ID (0Ah)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || x || MF || x || 0 || 1 || 0 || 1 || 0
 +
|-
 +
| command byte 1 || colspan="5" style="text-align: center;" | x || HD || colspan="2" style="text-align: center;" | US
 +
|-
 +
| Execution      || colspan="8" | The first correct ID information on the cylinder is stored in data register
 +
|-
 +
| result byte 0  || colspan="8" | ST0: status register 0
 +
|-
 +
| result byte 1  || colspan="8" | ST1: status register 1
 +
|-
 +
| result byte 2  || colspan="8" | ST2: status register 2
 +
|-
 +
| result byte 3  || colspan="8" | C: cylinder number
 +
|-
 +
| result byte 4  || colspan="8" | H: head number
 +
|-
 +
| result byte 5  || colspan="8" | R: sector number
 +
|-
 +
| result byte 6  || colspan="8" | N: bytes per sector
 +
|}
 +
 
 +
{| class="wikitable"
 +
|+ Read Track (02h)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || x || MF || SK || 0 || 0 || 0 || 1 || 0
 +
|-
 +
| command byte 1 || colspan="5" style="text-align: center;" | x || HD || colspan="2" style="text-align: center;" | US
 +
|-
 +
| command byte 2 || colspan="8" | C: cylinder number
 +
|-
 +
| command byte 3 || colspan="8" | H: head number
 +
|-
 +
| command byte 4 || colspan="8" | R: sector number
 +
|-
 +
| command byte 5 || colspan="8" | N: bytes per sector
 +
|-
 +
| command byte 6 || colspan="8" | EOT: end of track (ie. last sector in track)
 +
|-
 +
| command byte 7 || colspan="8" | GPL: gap 3 length
 +
|-
 +
| command byte 8 || colspan="8" | DTL: data length (if command byte 5==0)
 +
|-
 +
| Execution      || colspan="8" | FDC reads all data fields from index hole to EOT
 +
|-
 +
| result byte 0  || colspan="8" | ST0: status register 0
 +
|-
 +
| result byte 1  || colspan="8" | ST1: status register 1
 +
|-
 +
| result byte 2  || colspan="8" | ST2: status register 2
 +
|-
 +
| result byte 3  || colspan="8" | C: cylinder number
 +
|-
 +
| result byte 4  || colspan="8" | H: head number
 +
|-
 +
| result byte 5  || colspan="8" | R: sector number
 +
|-
 +
| result byte 6  || colspan="8" | N: bytes per sector
 +
|}
 +
 
 +
{| class="wikitable"
 +
|+ Format Track (0Dh)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || x || MF || x || 0 || 1 || 1 || 0 || 1
 +
|-
 +
| command byte 1 || colspan="5" style="text-align: center;" | x || HD || colspan="2" style="text-align: center;" | US
 +
|-
 +
| command byte 2 || colspan="8" | N: bytes per sector
 +
|-
 +
| command byte 3 || colspan="8" | SC: sectors per track
 +
|-
 +
| command byte 4 || colspan="8" | GPL: gap 3 length
 +
|-
 +
| command byte 5 || colspan="8" | D: filler pattern to write in each byte
 +
|-
 +
| Execution      || colspan="8" | FDC formats an entire track
 +
|-
 +
| result byte 0  || colspan="8" | ST0: status register 0
 +
|-
 +
| result byte 1  || colspan="8" | ST1: status register 1
 +
|-
 +
| result byte 2  || colspan="8" | ST2: status register 2
 +
|-
 +
| result byte 3  || colspan="8" | C: cylinder number
 +
|-
 +
| result byte 4  || colspan="8" | H: head number
 +
|-
 +
| result byte 5  || colspan="8" | R: sector number
 +
|-
 +
| result byte 6  || colspan="8" | N: bytes per sector
 +
|}
 +
 
 +
{| class="wikitable"
 +
|+ Seek (0Fh)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || colspan="3" style="text-align: center;" | x  || 0 || 1 || 1 || 1 || 1
 +
|-
 +
| command byte 1 || colspan="5" style="text-align: center;" | x || HD|| colspan="2" style="text-align: center;" | US
 +
|-
 +
| command byte 2 || colspan="8" | NCN: new cylinder number
 +
|-
 +
| Execution      || colspan="8" | Head is positioned over proper cylinder
 +
|}
 +
 
 +
{| class="wikitable"
 +
|+ Recalibrate (07h)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || colspan="3" style="text-align: center;" | x  || 0 || 0 || 1 || 1 || 1
 +
|-
 +
| command byte 1 || colspan="6" style="text-align: center;" | x || colspan="2" style="text-align: center;" | US
 +
|-
 +
| Execution      || colspan="8" | Head retracted to track 0
 +
|}
 +
 
 +
{| class="wikitable"
 +
|+ Sense Interrupt Status (08h)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || colspan="3" style="text-align: center;" | x || 0 || 1 || 0 || 0 || 0
 +
|-
 +
| result byte 0  || colspan="8" | ST0: status register 0
 +
|-
 +
| result byte 1  || colspan="8" | PCN: present cylinder number
 +
|}
 +
 
 +
{| class="wikitable"
 +
|+ Sense Drive Status (04h)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || colspan="3" style="text-align: center;" | x || 0 || 0 || 1 || 0 || 0
 +
|-
 +
| command byte 1 || colspan="5" style="text-align: center;" | x || HD || colspan="2" style="text-align: center;" | US
 +
|-
 +
| result byte 0  || colspan="8" | ST3: status register 3
 +
|}
 +
 
 +
{| class="wikitable"
 +
|+ Specify (03h)
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || colspan="3" style="text-align: center;" | x || 0 || 0 || 0 || 1 || 1
 +
|-
 +
| command byte 1 || colspan="4" style="text-align: center;" | SRT || colspan="4" style="text-align: center;" | HUT
 +
|-
 +
| command byte 2 || colspan="7" style="text-align: center;" | HLT || ND
 +
|}
 +
 
 +
{| class="wikitable"
 +
|+ Invalid
 +
|-
 +
!                !! D7 !! D6 !! D5 !! D4 !! D3 !! D2 !! D1 !! D0
 +
|-
 +
| command byte 0 || colspan="3" style="text-align: center;" | x || colspan="5" style="text-align: center;" | Invalid Codes
 +
|-
 +
| result byte  0 || colspan="8" | ST0: status register 0
 +
|}
 +
 
 +
Abbreviations used:
 +
*N = 2^(n+7) bytes, with N between 0 and 7. For example, N=2 means 512 bytes. There is conflicting info about the meaning of N=8: CPC-Power thinks it means 32768 bytes [https://www.cpc-power.com/SectorView.php?fiche=4225&slot=10&rang=0 Source]. Same for Roudoudou [https://64nops.wordpress.com/2021/09/09/a-la-decouverte-du-fdc-episode-5/ Source]. While CPCWiki thinks it means N=0 (128 bytes) [https://www.cpcwiki.eu/index.php/Format:DSK_disk_image_file_format Source]. On the Intel 82078 datasheet, it is precised that all values up to 7 are allowable.
 +
*MT = Multi-track (continue multi-sector function on other head)
 +
*MF = MFM mode (1 = Double Density)
 +
*SK = Skip deleted-data address mark (set if sectors with deleted DAM shall be skipped)
 +
*HD = Head number select
 +
*US = Unit select (drive select)
 +
 
 +
*HLT = Head Load Time: 2 to 254ms in 2ms increments
 +
*HUT = Head Unload Time: 16 to 240ms in 16ms increments
 +
*SRT = Step Rate Time: 1 to 16ms in 1ms increments (F = 1ms, E = 2ms, etc.)
 +
*ND = Non-DMA mode
 +
 
 +
Notes:
 +
* Specify: All timings will be doubled on CPC because the FDC runs at 4MHz instead of 8MHz for the datasheet
 +
* Format Track: The processor must supply C, H, R, N to the FDC for each sector during execution phase
 +
* Recalibrate: Walks up to 77 tracks, 80-track drives may need a second recalibrate if failed
 +
* Seek / Recalibrate: All read/write commands will be disabled until successful sense interrupt
 +
 
 +
<br>
  
 
== FDC Status Registers ==
 
== FDC Status Registers ==
  
−
The Main Status register can be always read through Port FB7E. The other four Status Registers cannot be read directly, instead they are returned through the data register as result bytes in response to specific commands.
+
The Main Status register can always be read through Port &FB7E. The other 4 Status Registers cannot be read directly, instead they are returned through the data register as result bytes in response to specific commands.
  
−
Main Status Register (Port FB7E)
+
Main Status Register (Port &FB7E):
  
−
   b0..3  DB FDD0..3 Busy (seek/recalib active, until succesful sense intstat)
+
   b0..3  DB   FDD0..3 Busy (seek/recalib active, until succesful sense intstat)
−
   b4    CB FDC Busy (still in command-, execution- or result-phase)
+
   b4    CB   FDC Busy (still in command-, execution- or result-phase)
−
   b5    EXM Execution Mode (still in execution-phase, non_DMA_only)
+
   b5    EXM Execution Mode (still in execution-phase, non_DMA_only)
−
   b6    DIO Data Input/Output (0=CPU->FDC, 1=FDC->CPU) (see b7)
+
   b6    DIO Data Input/Output (0=CPU->FDC, 1=FDC->CPU) (see b7)
−
   b7    RQM Request For Master (1=ready for next byte) (see b6 for direction)
+
   b7    RQM Request For Master (1=ready for next byte) (see b6 for direction)
  
−
Status Register 0
+
Status Register 0:
  
−
   b0,1  US Unit Select (driveno during interrupt)
+
   b0,1  US   Unit Select (driveno during interrupt)
−
   b2    HD Head Address (head during interrupt)
+
   b2    HD   Head Address (head during interrupt)
−
   b3    NR Not Ready (drive not ready or non-existing 2nd head selected)
+
   b3    NR   Not Ready (drive not ready or non-existing 2nd head selected)
−
   b4    EC Equipment Check (drive failure or recalibrate failed (retry))
+
   b4    EC   Equipment Check (drive failure or recalibrate failed (retry))
−
   b5    SE Seek End (Set if seek-command completed)
+
   b5    SE   Seek End (Set if seek-command completed)
−
   b6,7  IC Interrupt Code (0=OK, 1=aborted:readfail/OK if EN, 2=unknown cmd
+
   b6,7  IC   Interrupt Code (0=OK, 1=aborted:readfail/OK if EN, 2=unknown cmd
−
            or senseint with no int occured, 3=aborted:disc removed etc.)
+
              or senseint with no int occured, 3=aborted:disc removed etc.)
  
−
Status Register 1
+
Status Register 1:
  
−
   b0    MA Missing Address Mark (Sector_ID or DAM not found)
+
   b0    MA   Missing Address Mark (Sector_ID or DAM not found)
−
   b1    NW Not Writeable (tried to write/format disc with wprot_tab=on)
+
   b1    NW   Not Writeable (tried to write/format disc with wprot_tab=on)
−
   b2    ND No Data (Sector_ID not found, CRC fail in ID_field)
+
   b2    ND   No Data (Sector_ID not found, CRC fail in ID_field)
−
   b3,6  0   Not used
+
   b3,6  0   Not used
−
   b4    OR Over Run (CPU too slow in execution-phase (ca. 26us/Byte))
+
   b4    OR   Over Run (CPU too slow in execution-phase (ca. 26us/Byte))
−
   b5    DE Data Error (CRC-fail in ID- or Data-Field)
+
   b5    DE   Data Error (CRC-fail in ID- or Data-Field)
−
   b7    EN End of Track (set past most read/write commands) (see IC)
+
   b7    EN   End of Track (set past most read/write commands) (see IC)
  
−
Status Register 2
+
Status Register 2:
  
−
   b0    MD Missing Address Mark in Data Field (DAM not found)
+
   b0    MD   Missing Address Mark in Data Field (DAM not found)
−
   b1    BC Bad Cylinder (read/programmed track-ID different and read-ID = FF)
+
   b1    BC   Bad Cylinder (read/programmed track-ID different and read-ID = FF)
−
   b2    SN Scan Not Satisfied (no fitting sector found)
+
   b2    SN   Scan Not Satisfied (no fitting sector found)
−
   b3    SH Scan Equal Hit (equal)
+
   b3    SH   Scan Equal Hit (equal)
−
   b4    WC Wrong Cylinder (read/programmed track-ID different) (see b1)
+
   b4    WC   Wrong Cylinder (read/programmed track-ID different) (see b1)
−
   b5    DD Data Error in Data Field (CRC-fail in data-field)
+
   b5    DD   Data Error in Data Field (CRC-fail in data-field)
−
   b6    CM Control Mark (read/scan command found sector with deleted DAM)
+
   b6    CM   Control Mark (read/scan command found sector with deleted DAM)
−
   b7    0   Not Used
+
   b7    0   Not Used
  
−
Status Register 3
+
Status Register 3:
  
−
   b0,1  US Unit Select (pin 28,29 of FDC)
+
   b0,1  US   Unit Select (pin 28,29 of FDC)
−
   b2    HD Head Address (pin 27 of FDC)
+
   b2    HD   Head Address (pin 27 of FDC)
−
   b3    TS Two Side (0=yes, 1=no (!))
+
   b3    TS   Two Side (0=yes, 1=no (!))
−
   b4    T0 Track 0 (on track 0 we are)
+
   b4    T0   Track 0 (on track 0 we are)
−
   b5    RY Ready (drive ready signal)
+
   b5    RY   Ready (drive ready signal)
−
   b6    WP Write Protected (write protected)
+
   b6    WP   Write Protected (write protected)
−
   b7    FT Fault (if supported: 1=Drive failure)
+
   b7    FT   Fault (if supported: 1=Drive failure)
  
−
== Motor On/Off Flipflop ==
+
<br>
−
Writing 00h to Port FA7Eh turns all disk drive motors off, writing 01h turns all motors on. It is not possible to turn on/off the motor of a specific drive separately.
+
 
 +
== C, H, R, N values at result phase ==
 +
 
 +
If the processor terminates a read (or write) operation in the FDC, then the ID information in the Result phase is dependent upon the state of the MT bit and EOT byte:
 +
 
 +
{| class="wikitable"
 +
|-
 +
! rowspan="2" | MT !! rowspan="2" | HD !! rowspan="2" | Final Sector Transferred to Processor !!  colspan="4" style="text-align: center;" | ID Information at Result Phase
 +
|-
 +
! C !! H !! R !! N
 +
|-
 +
| 0 || 0 || style="text-align: center;" | Less than EOT || - || - || R + 1 || -
 +
|-
 +
| 0 || 0 || style="text-align: center;" | Equal to EOT || C + 1 || - || 0 || -
 +
|-
 +
| 0 || 1 || style="text-align: center;" | Less than EOT || - || - || R + 1 || -
 +
|-
 +
| 0 || 1 || style="text-align: center;" | Equal to EOT || C + 1 || - || 0 || -
 +
|-
 +
| 1 || 0 || style="text-align: center;" | Less than EOT || - || - || R + 1 || -
 +
|-
 +
| 1 || 0 || style="text-align: center;" | Equal to EOT || - || LSB || 0 || -
 +
|-
 +
| 1 || 1 || style="text-align: center;" | Less than EOT || - || - || R + 1 || -
 +
|-
 +
| 1 || 1 || style="text-align: center;" | Equal to EOT || C + 1 || LSB || 0 || -
 +
|}
 +
 
 +
* An empty cell means it is the same value as the one at the beginning of command execution
 +
* LSB (Least Significant Bit): The least significant bit of H is complemented
 +
 
 +
<br>
 +
 
 +
== Motor On/Off Flip-Flop ==
 +
Writing 00h to Port &FA7E turns all disk drive motors off, writing 01h turns all motors on. It is not possible to turn on/off the motor of a specific drive separately.
  
 
An exception are the Vortex F1-S, F1-D, M1-S and M1-D drives. (How are they different?)
 
An exception are the Vortex F1-S, F1-D, M1-S and M1-D drives. (How are they different?)
  
−
== Unconnected pins ==
+
Another exception is the Gotek drives. They don't take the motor flip-flop into account and are always on. [https://64nops.wordpress.com/2021/07/04/a-la-decouverte-du-fdc/ Source]
  
−
At the end of a successful read or write command, the program should send a ''Terminal Count'' (TC) signal to the FDC. However, in the CPC the TC pin isn't connected to the I/O bus, making it impossible for the program to confirm a correct operation. For that reason, the FDC will assume that the command has failed, and it'll return both Bit 6 in Status Register 0 and Bit 7 in Status Register 1 set. The program should ignore this error message.
+
Some FDC commands don't require the motor to be on. For example, the seek or recalibrate commands, that move the floppy drive head, work fine with the motor off. And seek/recalibrate also work with an empty drive (ie. without a floppy disk inserted). [https://64nops.wordpress.com/2021/07/10/a-la-decouverte-du-fdc-episode-2/ Source]
  
−
The CPC doesn't support floppy DMA transfers, and the FDC's Interrupt signal isn't used in the CPC.
+
The floppy disk rotates at a nominal speed of 300rpm, with some tolerance. This tolerance of the FDC has been measured by [[Roudoudou]] to be ±12% (it worked from 220 kbits/s to 283 kbits/s for a reference of 250 kbits/s). [https://64nops.wordpress.com/2021/09/02/a-la-decouverte-du-fdc-episode-4/ Source]
 +
 
 +
The FDC speed is more impressive when you realize the Amstrad CPC’s tape loads at only 2 kbits/s in fast mode. Note: tape loading can be way faster than that if an MP3 player is used instead of a real physical tape, as it has been demonstrated here: https://youtu.be/MAIsOIwgJWA
  
−
In the CPC the DS1 signal of the FDC is not connected, making it impossible to select floppy drives 2 and 3. The floppy drives 0 and 1 are selected instead.
+
<br>
  
 
== Notes ==
 
== Notes ==
Line 169: Line 659:
 
Despite the name, a sector with a ''Deleted data Address Mark'' (DAM) is not deleted; the DAM-flag is just another ID bit. 'Deleted' sectors can be read/written just like normal data sectors and if that ID bit is specified correctly in the command.
 
Despite the name, a sector with a ''Deleted data Address Mark'' (DAM) is not deleted; the DAM-flag is just another ID bit. 'Deleted' sectors can be read/written just like normal data sectors and if that ID bit is specified correctly in the command.
  
−
Usually single sided 40-track 3" disk drives are used in CPCs. For practical purposes, 42 tracks could be used — the limit is specific to the drive and some support more tracks but 42 is a good maximum. The FDC controller can be used to control 80-tracks and/or double sided drives, though AMSDOS doesn't support such formats. AMSDOS supports a maximum of two disk drives only.
+
<br>
 +
 
 +
== Standard floppy disk formats ==
 +
 
 +
[[AMSDOS]] has been designed to complement CP/M, not to compete with it. They share the same structure and can read and write each other's files.
 +
 
 +
There are 3 standard floppy disk formats in AMSDOS. They are all single-sided and double density (MFM), with the following characteristics:
 +
 
 +
{| class="wikitable" style="text-align: center;"
 +
! !! DATA !! VENDOR or SYSTEM !! IBM
 +
|-
 +
| Sector size || colspan="3" | N=2 (512 bytes)
 +
|-
 +
| Number of sectors || colspan="2" | 9 || 8
 +
|-
 +
| Sector names || &C1 to &C9 || &41 to &49 || &01 to &08
 +
|-
 +
| Sector interleave || colspan="2" | Yes || No
 +
|-
 +
| Formatting byte || colspan="3" | &E5
 +
|-
 +
| Starting track || colspan="3" | 00
 +
|-
 +
| Ending track || colspan="3" | 39
 +
|-
 +
| Catalog position || Track 0: sectors &C1 to &C4 || Track 2: sectors &41 to &44 || Track 1: sectors &01 to &04
 +
|-
 +
| Catalog size || colspan="3" | 2 KB
 +
|-
 +
| Catalog entries || colspan="3" | 64 max
 +
|-
 +
| Size per side || 178 KB || 169 KB || 154 KB
 +
|-
 +
| Diskette size || 356 KB || 338 KB || 308 KB
 +
|}
 +
 
 +
<br>
 +
 
 +
=== DATA format ===
 +
 
 +
It is the most commonly used format on Amstrad CPC as it offers the most available space among the standard formats.
 +
 
 +
<br>
 +
 
 +
=== SYSTEM format ===
 +
 
 +
The SYSTEM format is a VENDOR format with the addition of information to boot the CP/M on:
 +
* Track 0: sectors &41 (boot sector), &42 (configuration sector), &48, &49
 +
* Track 1: sectors &41, &46, &42, &47, &43, &48, &44, &49, &45
 +
 
 +
Type |CPM and you will find yourself under CP/M 2.2.
 +
 
 +
By the way, all the |CPM command does is load the 512 bytes of track 0 sector &41 into memory at address &100 and then execute it.
 +
 
 +
<br>
 +
 
 +
=== IBM format ===
 +
 
 +
The IBM format is only usable on early IBM PCs as it uses 8 sectors per track and the CP/M filesystem. This was the format used in MS-DOS 1.x. [https://www.os2museum.com/wp/dos/dos-1-0-and-1-1/ Source]
 +
 
 +
With MS-DOS 2.0 (1983), PC floppies switched to 9 sectors per track and the FAT12 filesystem. [https://minuszerodegrees.net/5150/early/5150_early.htm Source]
 +
 
 +
And MS-DOS 4.0 (1988) removed compatibility with MS-DOS 1.x formatted floppies. This is one of the reasons why MS-DOS 4.0 faced significant criticism.
 +
 
 +
Also, [[CP/M|CP/M]] 2.2 supports the IBM format but CP/M Plus does not.
 +
 
 +
<br>
 +
 
 +
=== Catalog structure ===
 +
 
 +
In CP/M (and AMSDOS), files are stored on disks in a flat structure and can only be organized using USER numbers. CP/M does not have a hierarchical directory structure (with folders and subfolders) like newer operating systems.
 +
 
 +
The catalog structure supports up to 64 entries of 32 bytes. A file larger than 16KB will require multiple entries in the catalog.
 +
 
 +
{| class="wikitable"
 +
|-
 +
! Byte offset !! Description !! Comment
 +
|-
 +
| 0 || User Number || USER goes from 0 to 255. USER 229 (&E5) is for deleted files. RSX only gives access to USER 0 to 15.
 +
|-
 +
| 1-8 || Filename (excluding full stop) || Always in CAPS and maximum 8 characters long.
 +
|-
 +
| 9-11 || Extension || Always in CAPS and maximum 3 characters long. Read Only flag on byte9 bit7. Hidden flag on byte10 bit7. Archive flag on byte11 bit7.
 +
|-
 +
| 12 || Current Extent || 0 is first extent. There can be up to 128K bytes (8 logical extents) directly addressed by a single directory entry. [http://www.cpm.z80.de/manuals/cpm22-m.pdf Source]
 +
|-
 +
| 13 || Reserved ||
 +
|-
 +
| 14 || Extent High Byte || Not used.
 +
|-
 +
| 15 || Record Count (Number of 128 Byte Blocks) || Goes up to 128 (&80).
 +
|-
 +
| 16–31 || Block IDs where to find the file data || 1 byte is used per 1KB block.
 +
|}
 +
 
 +
<br>
 +
 
 +
==== CAT'art ====
 +
 
 +
The catalog structure can be hacked by using ascii control characters (codes 0 to 31) to create decorated catalogs (CAT'art).
 +
 
 +
CAT never loads and executes a boot sector. It just displays the chars of the files using "TXT OUTPUT" (#bb5a) which will execute control codes as well.
 +
 
 +
There were already tools from the 80ies for modifying a directory in a way that will display colourful chars placed at any location on the screen by adding dummy file entries with 0KB sizes. Or you hardcode it directly by yourself, which allows much more chars and effects.
 +
 
 +
The trick is to disable text output at the end of a filename to prevent printing file sizes/line feeds and enable it again at the beginning of the next filename; and you also have to use one hidden char for sorting them in the correct order.
 +
 
 +
See here for more details: [http://cpc.sylvestre.org/technique/technique_catart1.html All about CAT'arts creation (FR)]
 +
 
 +
<br>
 +
 
 +
==== CP/M terminology ====
 +
 
 +
'''Record''': The basic unit of data access in CP/M, 128 bytes in size. This was the standard size for transferring data between memory and disk.
 +
 
 +
'''Block''': A group of records, 1 KB in size. Blocks were used to improve disk access efficiency by reading/writing multiple records at once.
 +
 
 +
'''Extent''': A group of blocks, 16 KB in size. CP/M used extents to manage file allocation, with each extent corresponding to a portion of a file on disk.
 +
 
 +
'''Sector''': The smallest physically addressable unit on a disk, 512 bytes in size on Amstrad CPC. CP/M accessed the disk at the sector level, though users typically worked with records.
 +
 
 +
<br>
 +
 
 +
==== File Headers ====
 +
 
 +
Cassette files are divided into 2KB blocks (then subdivided in 256-byte segments + CRC), each block being preceded by a 64-byte header.
 +
 
 +
AMSDOS files are usually stored with a 128-byte [[AMSDOS Header]] (based on cassette header) but can also be headerless, depending on the contents of the file. Unprotected ASCII files do not have header.
 +
 
 +
CP/M files do not have headers.
 +
 
 +
<br>
 +
 
 +
== Custom floppy disk formats ==
 +
 
 +
Usually single sided 40-track 3" disk drives are used in CPCs. For practical purposes, 42 tracks could be used — the limit is specific to the drive and some support more tracks but 42 is a good maximum.
 +
 
 +
RSX programs exist on top of AMSDOS to get up to 208 KB of usable space per side, by using 42 tracks with 10 sectors per track.
 +
 
 +
 
 +
The FDC controller can be used to control 80-tracks and/or double sided drives, though AMSDOS doesn't support such formats. To use 80-track drives and/or dual-head drives, you need to use another CPC DOS instead of AMSDOS. The most popular one is [[ParaDOS]]. It can handle up to 796 KB instead of 178 KB for AMSDOS and it supports 22 different disk file formats, including the three standard AMSDOS ones.
 +
 
 +
{| class="wikitable"
 +
|+ Supported Formats in ParaDOS
 +
! Format !! Capacity !! Catalog !! Type !! Sectors/Track !! Sectors
 +
|-
 +
| PARADOS 80 || 396k || 128 || SS || 10 || &91-&9a
 +
|-
 +
| PARADOS 41 || 203k || 64 || SS || 10 || &81-&8a
 +
|-
 +
| PARADOS 40D || 396k || 128 || DS || 10 || &a1-&aa
 +
|-
 +
| ROMDOS D1 || 716k || 128 || DS || 9 || &01-&09
 +
|-
 +
| ROMDOS D2 || 712k || 256 || DS || 9 || &21-&29
 +
|-
 +
| ROMDOS D10 || 796k || 128 || DS || 10 || &11-&1a
 +
|-
 +
| ROMDOS D20 || 792k || 256 || DS || 10 || &31-&3a
 +
|-
 +
| ROMDOS D40 || 396k || 128 || SS || 10 || &51-&5a
 +
|-
 +
| S-DOS || 396k || 128 || SS || 10 || &71-&7a
 +
|-
 +
| DATA (SS 40) || 178k || 64 || SS || 9 || &c1-&c9
 +
|-
 +
| DATA (DS 40) || 356k || 64 || DS || 9 || &c1-&c9 E
 +
|-
 +
| DATA (SS 80) || 356k || 64 || SS || 9 || &c1-&c9 E
 +
|-
 +
| DATA (DS 80) || 716k || 64 || DS || 9 || &c1-&c9 E
 +
|-
 +
| SYSTEM (SS 40) || 169k || 64 || SS || 9 || &41-&49
 +
|-
 +
| SYSTEM (DS 40) || 346k || 64 || DS || 9 || &41-&49 E
 +
|-
 +
| SYSTEM (SS 80) || 346k || 64 || SS || 9 || &41-&49 E
 +
|-
 +
| SYSTEM (DS 80) || 704k || 64 || DS || 9 || &41-&49 E
 +
|-
 +
| IBM (SS 40) || 169k || 64 || SS || 8 || &01-&08
 +
|-
 +
| IBM (DS 40) || 346k || 64 || DS || 8 || &01-&08 E
 +
|-
 +
| IBM (SS 80) || 346k || 64 || SS || 8 || &01-&08 E
 +
|-
 +
| IBM (DS 80) || 704k || 64 || DS || 8 || &01-&08 E
 +
|-
 +
| ULTRAFORM || 203k || 64 || SS || 9 || &10-&19
 +
|}
 +
Legend: SS = Single-Sided, DS = Double-Sided.
 +
 
 +
Half of the original AMSDOS rom is occupied by [[Dr. Logo]] from Digital Research. If you replace AMSDOS with ParaDOS, you will lose access to Dr. Logo.
 +
 
 +
There is also a special version of ParaDOS, called [[VaraDOS]], that supports the [[Vortex Format]].
 +
 
 +
[[UniDOS]] goes beyond and supports various mass-storage expansions, but also includes support for AMSDOS/ParaDOS floppy discs and tape.
 +
 
 +
<br>
  
 
== FDC Track Format ==
 
== FDC Track Format ==
−
[[File:FDC765 Track Format.png]]
 
  
−
== Internal details of the chip ==
+
The 765 FDC only supports the single-density IBM 3740 track format and the double-density IBM System/34 track format, which are the defacto standards for floppy disks in most computer systems. These formats have been created by an IBM engineer named Alan Shugart (not to be confused with Amstrad's CEO, Alan Sugar).
  
−
* [https://scarybeastsecurity.blogspot.com/2020/11/reverse-engineering-forgotten-1970s.html The decapped photos of Intel 8271, NEC D765 and Intel 8272 chips] prove that NEC D765 and Intel 8272 chips are identical.
+
[[File:FDC765 - FM and MFM.png|900px]]
  
−
* From [https://hackaday.com/2012/08/13/taking-a-look-at-decapped-ics/#comment-734991 a comment in the hackaday website]: "Internally this is a microcoded part with a primative controller of NEC’s own design. Testing microcode embedded in a part can be troublesome. The uPD765 had a few extra gates associated with the DMA Request and DMA Ack pins. Presenting a certain illegal combination here places the part into a “test” mode and allows the sequencer microcode to be output on the normal Data pins. The sequencer microcode is responsible for high level commands such as Read Track, Recalibrate, Format Track, or Write Data. There is a similar test mode for the nano-code array which serializes data at the floppy disk head."
+
On Amstrad CPC, the MFM MODE pin of the FDC is not connected. So the FM mode is unusable.
 +
 
 +
On Amstrad CPC, an MFM track contains about 6250 raw bytes: 200 ms per track (at 300rpm) / 32 µs per byte (with a bit cell of 4µs). Fun fact: You can squeeze a few more bytes on disk by using a floppy drive that spins a little slower, and counting on the tolerance of the FDC to make that disk readable on unmodified floppy drives.
 +
 
 +
Notes:
 +
* IAM signifies the beginning of a track.
 +
* IDAM marks the beginning of a sector's header.
 +
* DAM (or DDAM) marks the beginning of the actual data in a sector. Deleted data sectors are marked by an F8 byte instead of an FB byte.
 +
* In MFM encoding, IDAM and DAM are always preceded by three A1 bytes to help the FDC lock onto the data stream after a gap and accurately read the following datas. This is needed because MFM is more compact and harder to read than earlier encoding methods.
 +
* Gaps are necessary to accommodate variations in rotation speed between different drives and avoid overlapping.
 +
 
 +
The main competitor of the µPD765 FDC chip on the market was the WD179x FDC chip family. The primary difference between 765 and 179x controllers is that the 765 only does standard track formats (preamble, marks and data fields), while the 179x will write anything you tell it in the write track (formatting a track) mode.
 +
 
 +
<br>
 +
 
 +
=== Gaps Protection ===
 +
 
 +
Gaps was a common method of protecting floppy disks against copying on the Amstrad CPC, particularly with French software houses such as [[Infogrames]] and [[Loriciels]]. It consists of writing specific values (other than the standard &4E) in the separation area between 2 consecutive sectors.
 +
 
 +
When the protected program is launched, it checks if these special values (most often a string signature) are present. If they aren't, the program can then crash or reset the computer or format the disk – or in the case of some games, the player can play the game, but it will crash or freeze at some point.
 +
 
 +
The trick is that the 765 FDC can read the custom byte values in the gaps, but it cannot write them. This made it hard for people to make working copies of protected disks.
 +
 
 +
<br>
 +
 
 +
=== Weak Sectors Protection ===
 +
 
 +
Another common copy-protection scheme was using (fully or partially) unmagnetized sectors. The unmagnetized data would then appear as random values when read by the FDC.
 +
 
 +
When the protected program is launched, it reads these weak sectors multiple times. Due to their unstable nature, these sectors will return different data on each read. If the program detects this changing data, it recognizes the disk as an original and continues to run. If not, the program can then crash, reset the computer, etc.
 +
 
 +
The trick is that the FDC cannot unmagnetize portions of a sector or leave portions of a sector unmagnetized to recreate this effect on another floppy disk.
 +
 
 +
<br>
 +
 
 +
=== Error Detection ===
 +
 
 +
The FDC765 happens to use the exact same algorithm for error detection as the one the Amstrad firmware uses to check each 256-byte tape segments.
 +
 
 +
The CRC error-detecting code is initialised to &FFFF. It is updated byte by byte and uses the CCITT-CRC16 algorithm. It is written after the ID and data fields of each sector in big-endian format (high byte first and then low byte).
 +
 
 +
<br>
 +
 
 +
=== FM Encoding ===
 +
 
 +
FM (Frequency Modulation) encoding was one of the earliest methods used to store data on floppy disks by creating changes in the magnetic field, known as flux transitions, to represent binary data.
 +
 
 +
In FM encoding, each bit of data is divided into two distinct parts: a clock signal and a data signal. The clock signal is always present to indicate the timing, while the data signal only appears when the bit is a 1, and remains absent when the bit is a 0.
 +
 
 +
This constant clock pulse ensures that the FDC always knows where each bit begins and ends. For every bit of information written to the disk, there’s always one clock signal and, if the data is a 1, a data signal as well.
 +
 
 +
[[File:FM encoding scheme.png|600px]]
 +
 
 +
Legend: C=Clock, D=Data
 +
 
 +
<br>
 +
 
 +
=== MFM Encoding ===
 +
 
 +
MFM (Modified Frequency Modulation) was developed as a more efficient alternative to FM encoding. This method greatly reduces the number of transitions needed to represent data compared to FM.
 +
 
 +
If a cell contains a 1, the signal will be recorded in the middle of the cell. If a cell contains a 0, the signal will be recorded at the beginning of the cell, unless it was preceeded by a cell with a 1. If a signal is transmitted for a 0 cell, it is used as clock signal.
 +
 
 +
This clever encoding eliminates the need for separate clock signals for every bit, as they are implied by the data pattern. It allows the recording of double the density compared to FM without increasing the bit rate on the floppy material. Each bit cell has only half the size compared to FM.
 +
 
 +
[[File:MFM encoding scheme.png|600px]]
 +
 
 +
<br>
 +
 
 +
== HD Floppy Disks on CPC ==
 +
 
 +
It is theoretically possible to use HD floppy disks (1.44MB) on CPC by using either a Gotek drive or Amiga HD floppy drives spinning at 150rpm. However, nobody has ever written a CPC DOS to make use of it.
 +
 
 +
On a real floppy drive, if you want to fit more sectors on the same track, you have 2 options: you can make the FDC run faster, or you can make the disk spin slower.
 +
 
 +
Normally, HD disks use a faster FDC (with an automatic switch between the slow and fast modes).
 +
 
 +
But, for example on Amiga systems with HD drives, they used floppy drives that spin slower for HD disks (150 rotations per minutes instead of 300) and this allow to use the same controller as before. By the time the floppy has done one complete rotation, you can write 18 sectors instead of just 9.
 +
 
 +
With a real PC HD floppy drive, this requires some mechanical modifications, and you may get into trouble if the spinning speed is not fast enough.
 +
 
 +
But with the Gotek, this is not a problem. You can have as many sectors as you want, and the Gotek will generate the index pulse (simulating the floppy completing a turn) after it has sent them all. So it is essentially emulating a floppy that turns very slowly. The FDC has no problems handling that, but you may need to be a bit more relaxed than usual with the timeouts, as it will be some time before the sector you need will pass in front of the drive head, and the index pulse will also be slower than usual.
 +
 
 +
On a Gotek drive, you can even simulate fantasy floppy disks with up to 255 cylinders, and the FDC will handle them perfectly fine.
 +
 
 +
<br>
 +
 
 +
== Mass Storage via FDC ==
 +
 
 +
The Gotek drive (with a FlashFloppy or HxC firmware) has a special direct access mode that allows it to be used as a poor's man hard drive, offering access to up to 32 GB of storage space. It is accessible via the track 255. [https://hxc2001.com/download/floppy_drive_emulator/SDCard_HxC_Floppy_Emulator_Direct_Access_mode.pdf Source]
 +
 
 +
This is a great feature as it alleviates the need for another mass storage expansion. And the relative slowness of this solution (~15 KB/s) compared to a proper mass storage device (~130 KB/s with [[Symbiface II]]) is not much of an issue on Amstrad CPC.
 +
 
 +
This special Gotek direct access mode is supported in [[SymbOS]]. [https://www.cpcwiki.eu/forum/applications/symbos-with-hxc-direct-access-fat32-support/ Source]
 +
 
 +
<br>
  
 
== FDC Block Diagram ==
 
== FDC Block Diagram ==
−
[[File:FDC Intel 8272A block diagram.gif]]
+
 
 +
The FDC chip is quite different from the other CPC chips. It contains its own internal CPU, ROM and RAM.
 +
 
 +
[[File:WDC37C65 block diagram.png|700px]]
 +
 
 +
<br>
 +
 
 +
=== Internal details of the chip ===
 +
 
 +
Internally this is a microcoded part with a primative controller of NEC’s own design.
 +
 
 +
Testing microcode embedded in a part can be troublesome. The uPD765 had a few extra gates associated with the DMA Request and DMA Ack pins.
 +
 
 +
Presenting a certain illegal combination here places the part into a “test” mode and allows the sequencer microcode to be output on the normal Data pins. The sequencer microcode is responsible for high level commands such as Read Track, Recalibrate, Format Track, or Write Data.
 +
 
 +
There is a similar test mode for the nano-code array which serializes data at the floppy disk head. [https://hackaday.com/2012/08/13/taking-a-look-at-decapped-ics/#comment-734991 Source]
 +
 
 +
<br>
 +
 
 +
=== Intel 8272 FDC ===
 +
 
 +
NEC uPD765 (or just D765) is exactly the same chip as the 8272. NEC and Intel cross-licensed a bunch of IP back in the day. [https://forum.vcfed.org/index.php?threads/8272-fdc-to-8-drive-connections.45816/#post-557651 Source]
 +
 
 +
The 8272/µPD765 was the result of a cross-licensing deal between NEC and Intel. It was essentially NEC design. [https://classiccmp.org/mailman3/hyperkitty/list/cctalk@classiccmp.org/thread/MMWRWPGKWRVOLMUBIFQTZSCRRMF3YOXF/ Source]
 +
 
 +
[https://scarybeastsecurity.blogspot.com/2020/11/reverse-engineering-forgotten-1970s.html The decapped photos of Intel 8271, NEC D765 and Intel 8272 chips] prove that NEC D765 and Intel 8272 chips are identical.
 +
 
 +
<br>
  
 
== Generic System Diagram ==
 
== Generic System Diagram ==
−
The Amstrad CPC and Amstrad Plus do not have a DMA controller associated with the FDC. The INT pin of the FDC is not connected either.
+
The Amstrad CPC and Amstrad Plus do not have a DMA controller associated with the FDC. And the clock runs at 4MHz instead of 8MHz.
  
−
[[File:UPD765A System Diagram.png]]
+
[[File:FDC765 - System Diagram.png|800px]]
  
−
== 3-inch Floppy Drive Interface ==
+
<br>
−
[[File:Interface FDC - Floppy drive.png]]
+
 
 +
=== Unconnected Pins ===
 +
 
 +
The DRQ (14), INT (18), VCO SYNC (24), MFM MODE (26), US1 (28), and HEAD LOAD (36) pins are not connected. The TC (16) and RESET (1) pins are connected together. [https://www.cpcwiki.eu/imgs/4/45/CPC6128_Disk_Interface_Schematic.png Source]
 +
 
 +
At the end of a successful read or write command, the program should send a ''Terminal Count'' (TC) signal to the FDC. However, in the CPC the TC pin isn't connected to the I/O bus, making it impossible for the program to confirm a correct operation. For that reason, the FDC will assume that the command has failed, and it'll return both Bit 6 in Status Register 0 and Bit 7 in Status Register 1 set. The program should ignore this error message.
 +
 
 +
The CPC doesn't support floppy DMA transfers, and the FDC's Interrupt signal isn't used in the CPC.
 +
 
 +
The FDC controller inside the CPC or in the [[Amstrad External Disk Drive|Amstrad DDI-1]] expansion doesn't have the US1 pin connected. This means it can only select floppy drives 0 and 1, and not drives 2 and 3. And AMSDOS supports a maximum of two disk drives only.
 +
 
 +
However, the FDC in the [[Vortex Disc Drives|Vortex disc interface]] does have the US1 pin connected, and so it can manage up to 4 floppy drives.
 +
 
 +
<br>
 +
 
 +
=== ABBA switch ===
 +
 
 +
The [[ABBA switch]] is a common hardware modification that allows users to swap between Drive A and Drive B.
 +
 
 +
On Amstrad CPC, some games and other software were designed to run specifically from Drive A, creating a problem when the disk you needed was in Drive B.
 +
 
 +
The ABBA switch resolved this issue by allowing you to "swap" the designation of the two drives. When the switch is activated, Drive A becomes Drive B, and vice versa, effectively swapping their roles.
 +
 
 +
<br>
 +
 
 +
== PC to CPC floppy connector ==
 +
[[File:Cpc6128floppytopcfloppy.gif]]
 +
 
 +
<br>
 +
 
 +
=== Ready / Disk Changed signal ===
 +
 
 +
This signal differs between floppy drives model:
 +
 
 +
*For 3inch floppy drives, it is a "Ready" signal (pin 26). The /RDY signal turns on when a disk is inserted and spinning in the drive, usually after detecting 2 or 3 index pulses, depending on the drive model. It turns off immediately if the disk is removed or the motor stops.
 +
 
 +
*For PC 3.5inch floppy drives, it is a "Disk Changed" signal (pin 34). The /DSKCHG signal determines whether the same disk loaded during the previous disk access is still in the drive.
 +
 
 +
The easiest solution to this issue is to force the Ready signal on the cable. However, the CPC will hang if you type the CAT command with no disk inserted (inserting a disk will unblock it).
 +
 
 +
Alternatively, you can [[Modify PC floppy drives]] to create a Ready signal, or use Amiga floppy drives, which already have this signal.
 +
 
 +
Gotek drives with FlashFloppy or HxC firmware can also be configured to simulate the Ready signal. Don't forget to use a proper floppy drive cable then, not the one commonly sold by CPC hobbyists with the Ready signal forced.
 +
 
 +
<br>
 +
 
 +
=== PC Floppy Drive types ===
 +
 
 +
The IBM PC supports 3 standard diskette formats on a 5.25 inch drive:
 +
* The earliest IBM PCs used single-sided, double density, 40 cylinders, 300 RPM,  floppy drives which yield a capacity of 160 KB per side. And MS-DOS 1.0 only supported single-sided floppy drives.
 +
* Double-sided floppy drives were introduced in the IBM PC in 1982 and are supported in MS-DOS 1.1. They originally had a capacity of 320 KB per diskette. MS-DOS 2.0 extended the capacity to 360 KB with a new disk format. [https://minuszerodegrees.net/5150/early/5150_early.htm Source]
 +
* A new floppy drive was introduced with the PC/AT in 1984. It is double sided, quad density, 80 cylinders, with a total capacity of 1.2 MB. The high density drive rotates at '''360 RPM''', so only 15 sectors can be written on a track instead of 18.
 +
 
 +
The IBM PS/2 introduced two standard 3.5 inch diskette formats:
 +
* The first is a double sided, double density, 80 cylinders, format yielding a capacity of 720KB. The double density drive rotates at 300 RPM.
 +
* The other is double sided, quad density, 80 cylinders, with a total capacity of 1.44 MB. The high density drive rotates at 300 RPM.
 +
 
 +
Fun fact: The original IBM PC didn’t have a hard drive, even as an option. And MS-DOS 1.x didn't have any support for hard drives either. Hard drives only became a thing with the introduction of the IBM PC/XT and MS-DOS 2.0 in 1983. But the floppy drive was not the only option to load programs on the original IBM PC. You could also use a tape deck, just like on Amstrad CPC. However, the tape port disappeared with the PC/XT. [https://en.wikipedia.org/wiki/IBM_cassette_tape Source]
 +
 
 +
<br>
  
 
== FDD Block Diagram ==
 
== FDD Block Diagram ==
−
[[File:Floppy Disk Drive - Block Diagram.png]]
+
[[File:Floppy Disk Drive - Block Diagram.png|700px]]
 +
 
 +
<br>
 +
 
 +
== Chip Variants ==
 +
 
 +
NEC has developed various successors to the original uPD765, such as the uPD72065, uPD72067, and uPD72069.
 +
 
 +
Intel has also produced successors of the 8272, such as the 82072, 82077 and 82078.
 +
 
 +
<br>
  
 
== Datasheets ==
 
== Datasheets ==
  
 
* [[Media:UPD765_App_Note_Mar79.pdf| NEC uPD765 Datasheet preliminary (1979)]] [[Media:D765 NEC.pdf]] [[Media:UPD765-NEC.pdf]] [[Media:Z765A datasheet.pdf]] - uPD765 disc controller
 
* [[Media:UPD765_App_Note_Mar79.pdf| NEC uPD765 Datasheet preliminary (1979)]] [[Media:D765 NEC.pdf]] [[Media:UPD765-NEC.pdf]] [[Media:Z765A datasheet.pdf]] - uPD765 disc controller
−
* [[Media:Intel 8272A Datasheet preliminary (1982).pdf]] [[Media:Datasheet.hk_d8272a_2873060.pdf|Intel 8272A Datasheet (1986)]] - Licensed clone of the uPD765
+
* [[Media:Intel 8272A Datasheet preliminary (1982).pdf]] [[Media:Datasheet.hk_d8272a_2873060.pdf|Intel 8272A Datasheet (1986)]] [[Media:Floppy Disk Controller(FDC) UM8272A UM8272A-4.pdf]] - Licensed clone of the uPD765
−
* [[Media:FDC9229BT Datasheet.pdf]] - FDC9229BT data separator
+
* [[Media:WD37C65 datasheet.pdf]] - NEC 765 controller clone with onboard data seperator and AT/EISA compatibility
−
* [[Media:SED9420.pdf]] - SED9420C data separator
+
* [[Media:TN6-1 9216 Floppy Disk Data Separator Jun82.pdf]] [[Media:FDC9216 datasheet.PDF]] [[Media:SED9420.pdf]] - Data separators
 
* [[Media:DDI Schematic.png]] - DDI-1 Schematic (disc interface for CPC464)
 
* [[Media:DDI Schematic.png]] - DDI-1 Schematic (disc interface for CPC464)
−
* [[Media:Panasonic-3 inch Floppy Drive EME-150.pdf]] Panasonic EME-150M 3inch Floppy Disk Drive Datasheet
+
* [[Media:Panasonic-3 inch Floppy Drive EME-150.pdf]] [[Media:NEC_FD1035_Floppy.pdf]] - Floppy disk drives
−
* [[Media:NEC_FD1035_Floppy.pdf]] - NEC FD1035 3.5inch Floppy Disk Drive Datasheet (1984)
+
* [[Media:Floppy User Guide.pdf]] - Floppy User Guide
 +
 
 +
<br>
  
 
== External links ==
 
== External links ==
 
*[http://quasar.cpcscene.net/doku.php?id=assem:fdc Quasar FDC documentation (in french)]
 
*[http://quasar.cpcscene.net/doku.php?id=assem:fdc Quasar FDC documentation (in french)]
 
*[https://64nops.wordpress.com/2021/07/04/a-la-decouverte-du-fdc/ FDC blog articles (in french)]
 
*[https://64nops.wordpress.com/2021/07/04/a-la-decouverte-du-fdc/ FDC blog articles (in french)]
−
*[https://info-coach.fr/atari/hardware/FD-Hard.php Atari ST Floppy Disk hardware analysis]
+
*[https://www.cpc-power.com/cpcarchives/index.php?page=articles&num=92 Floppy disk formats (in french)]
 +
*[https://info-coach.fr/atari/hardware/FD-Hard.php Atari ST Floppy Drive hardware analysis]
 +
*[https://map.grauw.nl/articles/low-level-disk/ MSX low-level disk storage article]
  
 
[[Category:CPC Internal Components]][[Category:Programming]][[Category:DATA Storage]][[Category:Electronic Component]]
 
[[Category:CPC Internal Components]][[Category:Programming]][[Category:DATA Storage]][[Category:Electronic Component]]

Latest revision as of 06:23, 10 November 2024

µPD765 - Floppy Disc Controller (used in DDI-1 and CPC 664/6128).

The ports used by Amstrad and compatible interfaces use:

  • Port &FA7E - Floppy Motor On/Off Flipflop
  • Port &FB7E - FDC 765 Main Status Register (read only)
  • Port &FB7F - FDC 765 Data Register (read/write)

The Vortex disc interface uses other ports. See its dedicated wiki page.


IC Models used in CPC

More than one manufacturer made 765 compatible ICs. These are the ones known to be used in the CPC by looking at pictures of CPC mainboards.

All should operate almost identically.

The following data seperators are used:

The CPC464, CPC472, 464 Plus and GX4000 are not equipped with a FDC chip.

All the floppy disk drive models used by Amstrad are referenced here: Amstrad FDD part


Accessing the FDC 765

The Main Status Register (Port &FB7E) signalizes when the FDC is ready to send/receive the next byte through the Data Register.

The Data Register (Port &FB7F) is used to write Commands and Parameters, to read/write data bytes, and to receive result bytes. These 3 operations are called Command-, Execution-, and Result-Phase.


Command Phase

A command consists of a command byte (eventually including the MT, MF, SK bits), and up to 8 parameter bytes.


Execution Phase

During this phase, the actual data is transferred (if any). Usually that are the data bytes for the read/written sector(s), except for the Format Track Command, in that case 4 bytes for each sector are transferred.

During data transfers between the FDC and the processor, the FDC must be serviced every 26µs (for MFM mode with CPC timings) or the FDC terminates the FDC command.


Result Phase

Returns up to 7 result bytes (depending on the command) that are containing status information. The Recalibrate and Seek Track commands do not return result bytes directly, instead the program must wait until the Main Status Register signalizes that the command has been completed, and then it must (!) send a Sense Interrupt State command to 'terminate' the Seek/Recalibrate command.

During the result phase, all the result bytes must be read. The FDC will not accept a new command until all the result bytes are read.


The 15 FDC Commands

Scan Equal (11h)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 MT MF SK 1 0 0 0 1
command byte 1 x HD US
command byte 2 C: cylinder number
command byte 3 H: head number
command byte 4 R: sector number
command byte 5 N: bytes per sector
command byte 6 EOT: end of track (ie. last sector in track)
command byte 7 GPL: gap 3 length
command byte 8 STP: scan test (1=scan contiguous, 2=scan alternate)
Execution Data compared between the FDD and main-system
result byte 0 ST0: status register 0
result byte 1 ST1: status register 1
result byte 2 ST2: status register 2
result byte 3 C: cylinder number
result byte 4 H: head number
result byte 5 R: sector number
result byte 6 N: bytes per sector
Scan Low or Equal (19h)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 MT MF SK 1 1 0 0 1
command byte 1 x HD US
command byte 2 C: cylinder number
command byte 3 H: head number
command byte 4 R: sector number
command byte 5 N: bytes per sector
command byte 6 EOT: end of track (ie. last sector in track)
command byte 7 GPL: gap 3 length
command byte 8 STP: scan test (1=scan contiguous, 2=scan alternate)
Execution Data compared between the FDD and main-system
result byte 0 ST0: status register 0
result byte 1 ST1: status register 1
result byte 2 ST2: status register 2
result byte 3 C: cylinder number
result byte 4 H: head number
result byte 5 R: sector number
result byte 6 N: bytes per sector
Scan High or Equal (1Dh)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 MT MF SK 1 1 1 0 1
command byte 1 x HD US
command byte 2 C: cylinder number
command byte 3 H: head number
command byte 4 R: sector number
command byte 5 N: bytes per sector
command byte 6 EOT: end of track (ie. last sector in track)
command byte 7 GPL: gap 3 length
command byte 8 STP: scan test (1=scan contiguous, 2=scan alternate)
Execution Data compared between the FDD and main-system
result byte 0 ST0: status register 0
result byte 1 ST1: status register 1
result byte 2 ST2: status register 2
result byte 3 C: cylinder number
result byte 4 H: head number
result byte 5 R: sector number
result byte 6 N: bytes per sector
Read Data (06h)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 MT MF SK 0 0 1 1 0
command byte 1 x HD US
command byte 2 C: cylinder number
command byte 3 H: head number
command byte 4 R: sector number
command byte 5 N: bytes per sector
command byte 6 EOT: end of track (ie. last sector in track)
command byte 7 GPL: gap 3 length
command byte 8 DTL: data length (if command byte 5==0)
Execution Data-transfer from the FDD
result byte 0 ST0: status register 0
result byte 1 ST1: status register 1
result byte 2 ST2: status register 2
result byte 3 C: cylinder number
result byte 4 H: head number
result byte 5 R: sector number
result byte 6 N: bytes per sector
Read Deleted Data (0Ch)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 MT MF SK 0 1 1 0 0
command byte 1 x HD US
command byte 2 C: cylinder number
command byte 3 H: head number
command byte 4 R: sector number
command byte 5 N: bytes per sector
command byte 6 EOT: end of track (ie. last sector in track)
command byte 7 GPL: gap 3 length
command byte 8 DTL: data length (if command byte 5==0)
Execution Data-transfer from the FDD
result byte 0 ST0: status register 0
result byte 1 ST1: status register 1
result byte 2 ST2: status register 2
result byte 3 C: cylinder number
result byte 4 H: head number
result byte 5 R: sector number
result byte 6 N: bytes per sector
Write Data (05h)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 MT MF x 0 0 1 0 1
command byte 1 x HD US
command byte 2 C: cylinder number
command byte 3 H: head number
command byte 4 R: sector number
command byte 5 N: bytes per sector
command byte 6 EOT: end of track (ie. last sector in track)
command byte 7 GPL: gap 3 length
command byte 8 DTL: data length (if command byte 5==0)
Execution Data-transfer to the FDD
result byte 0 ST0: status register 0
result byte 1 ST1: status register 1
result byte 2 ST2: status register 2
result byte 3 C: cylinder number
result byte 4 H: head number
result byte 5 R: sector number
result byte 6 N: bytes per sector
Write Deleted Data (09h)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 MT MF x 0 1 0 0 1
command byte 1 x HD US
command byte 2 C: cylinder number
command byte 3 H: head number
command byte 4 R: sector number
command byte 5 N: bytes per sector
command byte 6 EOT: end of track (ie. last sector in track)
command byte 7 GPL: gap 3 length
command byte 8 DTL: data length (if command byte 5==0)
Execution Data-transfer to the FDD
result byte 0 ST0: status register 0
result byte 1 ST1: status register 1
result byte 2 ST2: status register 2
result byte 3 C: cylinder number
result byte 4 H: head number
result byte 5 R: sector number
result byte 6 N: bytes per sector
Read ID (0Ah)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 x MF x 0 1 0 1 0
command byte 1 x HD US
Execution The first correct ID information on the cylinder is stored in data register
result byte 0 ST0: status register 0
result byte 1 ST1: status register 1
result byte 2 ST2: status register 2
result byte 3 C: cylinder number
result byte 4 H: head number
result byte 5 R: sector number
result byte 6 N: bytes per sector
Read Track (02h)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 x MF SK 0 0 0 1 0
command byte 1 x HD US
command byte 2 C: cylinder number
command byte 3 H: head number
command byte 4 R: sector number
command byte 5 N: bytes per sector
command byte 6 EOT: end of track (ie. last sector in track)
command byte 7 GPL: gap 3 length
command byte 8 DTL: data length (if command byte 5==0)
Execution FDC reads all data fields from index hole to EOT
result byte 0 ST0: status register 0
result byte 1 ST1: status register 1
result byte 2 ST2: status register 2
result byte 3 C: cylinder number
result byte 4 H: head number
result byte 5 R: sector number
result byte 6 N: bytes per sector
Format Track (0Dh)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 x MF x 0 1 1 0 1
command byte 1 x HD US
command byte 2 N: bytes per sector
command byte 3 SC: sectors per track
command byte 4 GPL: gap 3 length
command byte 5 D: filler pattern to write in each byte
Execution FDC formats an entire track
result byte 0 ST0: status register 0
result byte 1 ST1: status register 1
result byte 2 ST2: status register 2
result byte 3 C: cylinder number
result byte 4 H: head number
result byte 5 R: sector number
result byte 6 N: bytes per sector
Seek (0Fh)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 x 0 1 1 1 1
command byte 1 x HD US
command byte 2 NCN: new cylinder number
Execution Head is positioned over proper cylinder
Recalibrate (07h)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 x 0 0 1 1 1
command byte 1 x US
Execution Head retracted to track 0
Sense Interrupt Status (08h)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 x 0 1 0 0 0
result byte 0 ST0: status register 0
result byte 1 PCN: present cylinder number
Sense Drive Status (04h)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 x 0 0 1 0 0
command byte 1 x HD US
result byte 0 ST3: status register 3
Specify (03h)
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 x 0 0 0 1 1
command byte 1 SRT HUT
command byte 2 HLT ND
Invalid
D7 D6 D5 D4 D3 D2 D1 D0
command byte 0 x Invalid Codes
result byte 0 ST0: status register 0

Abbreviations used:

  • N = 2^(n+7) bytes, with N between 0 and 7. For example, N=2 means 512 bytes. There is conflicting info about the meaning of N=8: CPC-Power thinks it means 32768 bytes Source. Same for Roudoudou Source. While CPCWiki thinks it means N=0 (128 bytes) Source. On the Intel 82078 datasheet, it is precised that all values up to 7 are allowable.
  • MT = Multi-track (continue multi-sector function on other head)
  • MF = MFM mode (1 = Double Density)
  • SK = Skip deleted-data address mark (set if sectors with deleted DAM shall be skipped)
  • HD = Head number select
  • US = Unit select (drive select)
  • HLT = Head Load Time: 2 to 254ms in 2ms increments
  • HUT = Head Unload Time: 16 to 240ms in 16ms increments
  • SRT = Step Rate Time: 1 to 16ms in 1ms increments (F = 1ms, E = 2ms, etc.)
  • ND = Non-DMA mode

Notes:

  • Specify: All timings will be doubled on CPC because the FDC runs at 4MHz instead of 8MHz for the datasheet
  • Format Track: The processor must supply C, H, R, N to the FDC for each sector during execution phase
  • Recalibrate: Walks up to 77 tracks, 80-track drives may need a second recalibrate if failed
  • Seek / Recalibrate: All read/write commands will be disabled until successful sense interrupt


FDC Status Registers

The Main Status register can always be read through Port &FB7E. The other 4 Status Registers cannot be read directly, instead they are returned through the data register as result bytes in response to specific commands.

Main Status Register (Port &FB7E): 

 b0..3  DB   FDD0..3 Busy (seek/recalib active, until succesful sense intstat)
 b4     CB   FDC Busy (still in command-, execution- or result-phase)
 b5     EXM  Execution Mode (still in execution-phase, non_DMA_only)
 b6     DIO  Data Input/Output (0=CPU->FDC, 1=FDC->CPU) (see b7)
 b7     RQM  Request For Master (1=ready for next byte) (see b6 for direction)

Status Register 0: 

 b0,1   US   Unit Select (driveno during interrupt)
 b2     HD   Head Address (head during interrupt)
 b3     NR   Not Ready (drive not ready or non-existing 2nd head selected)
 b4     EC   Equipment Check (drive failure or recalibrate failed (retry))
 b5     SE   Seek End (Set if seek-command completed)
 b6,7   IC   Interrupt Code (0=OK, 1=aborted:readfail/OK if EN, 2=unknown cmd
             or senseint with no int occured, 3=aborted:disc removed etc.)

Status Register 1: 

 b0     MA   Missing Address Mark (Sector_ID or DAM not found)
 b1     NW   Not Writeable (tried to write/format disc with wprot_tab=on)
 b2     ND   No Data (Sector_ID not found, CRC fail in ID_field)
 b3,6   0    Not used
 b4     OR   Over Run (CPU too slow in execution-phase (ca. 26us/Byte))
 b5     DE   Data Error (CRC-fail in ID- or Data-Field)
 b7     EN   End of Track (set past most read/write commands) (see IC)

Status Register 2: 

 b0     MD   Missing Address Mark in Data Field (DAM not found)
 b1     BC   Bad Cylinder (read/programmed track-ID different and read-ID = FF)
 b2     SN   Scan Not Satisfied (no fitting sector found)
 b3     SH   Scan Equal Hit (equal)
 b4     WC   Wrong Cylinder (read/programmed track-ID different) (see b1)
 b5     DD   Data Error in Data Field (CRC-fail in data-field)
 b6     CM   Control Mark (read/scan command found sector with deleted DAM)
 b7     0    Not Used

Status Register 3: 

 b0,1   US   Unit Select (pin 28,29 of FDC)
 b2     HD   Head Address (pin 27 of FDC)
 b3     TS   Two Side (0=yes, 1=no (!))
 b4     T0   Track 0 (on track 0 we are)
 b5     RY   Ready (drive ready signal)
 b6     WP   Write Protected (write protected)
 b7     FT   Fault (if supported: 1=Drive failure)


C, H, R, N values at result phase

If the processor terminates a read (or write) operation in the FDC, then the ID information in the Result phase is dependent upon the state of the MT bit and EOT byte:

MT HD Final Sector Transferred to Processor ID Information at Result Phase
C H R N
0 0 Less than EOT - - R + 1 -
0 0 Equal to EOT C + 1 - 0 -
0 1 Less than EOT - - R + 1 -
0 1 Equal to EOT C + 1 - 0 -
1 0 Less than EOT - - R + 1 -
1 0 Equal to EOT - LSB 0 -
1 1 Less than EOT - - R + 1 -
1 1 Equal to EOT C + 1 LSB 0 -
  • An empty cell means it is the same value as the one at the beginning of command execution
  • LSB (Least Significant Bit): The least significant bit of H is complemented


Motor On/Off Flip-Flop

Writing 00h to Port &FA7E turns all disk drive motors off, writing 01h turns all motors on. It is not possible to turn on/off the motor of a specific drive separately.

An exception are the Vortex F1-S, F1-D, M1-S and M1-D drives. (How are they different?)

Another exception is the Gotek drives. They don't take the motor flip-flop into account and are always on. Source

Some FDC commands don't require the motor to be on. For example, the seek or recalibrate commands, that move the floppy drive head, work fine with the motor off. And seek/recalibrate also work with an empty drive (ie. without a floppy disk inserted). Source

The floppy disk rotates at a nominal speed of 300rpm, with some tolerance. This tolerance of the FDC has been measured by Roudoudou to be ±12% (it worked from 220 kbits/s to 283 kbits/s for a reference of 250 kbits/s). Source

The FDC speed is more impressive when you realize the Amstrad CPC’s tape loads at only 2 kbits/s in fast mode. Note: tape loading can be way faster than that if an MP3 player is used instead of a real physical tape, as it has been demonstrated here: https://youtu.be/MAIsOIwgJWA


Notes

Before accessing a disk you should issue a recalibrate command to the drive to move the head backwards until the track zero signal from the drive is sensed by the FDC. The FDC will also set its track counter for that drive to zero.

On an 80-track drive you may need to repeat that twice because some models of the FDC stop after 77 steps so if recalibrating from track 78 or above the controller might not reach track zero.

In order to format, read or write a sector on a specific track you must first seek that track using command 0Fh. That'll move the read/write head to the physical track number. If you don't do that then the FDC will attempt to read/write data from/to the current physical track, irrespective of the specified logical track ID.

The track, sector, and head IDs are logical IDs only. These logical IDs are defined when formatting the disk and aren't required to reflect the physical track, sector, or head numbers. However, when reading or writing a sector you must specify the same IDs that have been used during formatting.

Despite the name, a sector with a Deleted data Address Mark (DAM) is not deleted; the DAM-flag is just another ID bit. 'Deleted' sectors can be read/written just like normal data sectors and if that ID bit is specified correctly in the command.


Standard floppy disk formats

AMSDOS has been designed to complement CP/M, not to compete with it. They share the same structure and can read and write each other's files.

There are 3 standard floppy disk formats in AMSDOS. They are all single-sided and double density (MFM), with the following characteristics:

DATA VENDOR or SYSTEM IBM
Sector size N=2 (512 bytes)
Number of sectors 9 8
Sector names &C1 to &C9 &41 to &49 &01 to &08
Sector interleave Yes No
Formatting byte &E5
Starting track 00
Ending track 39
Catalog position Track 0: sectors &C1 to &C4 Track 2: sectors &41 to &44 Track 1: sectors &01 to &04
Catalog size 2 KB
Catalog entries 64 max
Size per side 178 KB 169 KB 154 KB
Diskette size 356 KB 338 KB 308 KB


DATA format

It is the most commonly used format on Amstrad CPC as it offers the most available space among the standard formats.


SYSTEM format

The SYSTEM format is a VENDOR format with the addition of information to boot the CP/M on:

  • Track 0: sectors &41 (boot sector), &42 (configuration sector), &48, &49
  • Track 1: sectors &41, &46, &42, &47, &43, &48, &44, &49, &45

Type |CPM and you will find yourself under CP/M 2.2.

By the way, all the |CPM command does is load the 512 bytes of track 0 sector &41 into memory at address &100 and then execute it.


IBM format

The IBM format is only usable on early IBM PCs as it uses 8 sectors per track and the CP/M filesystem. This was the format used in MS-DOS 1.x. Source

With MS-DOS 2.0 (1983), PC floppies switched to 9 sectors per track and the FAT12 filesystem. Source

And MS-DOS 4.0 (1988) removed compatibility with MS-DOS 1.x formatted floppies. This is one of the reasons why MS-DOS 4.0 faced significant criticism.

Also, CP/M 2.2 supports the IBM format but CP/M Plus does not.


Catalog structure

In CP/M (and AMSDOS), files are stored on disks in a flat structure and can only be organized using USER numbers. CP/M does not have a hierarchical directory structure (with folders and subfolders) like newer operating systems.

The catalog structure supports up to 64 entries of 32 bytes. A file larger than 16KB will require multiple entries in the catalog.

Byte offset Description Comment
0 User Number USER goes from 0 to 255. USER 229 (&E5) is for deleted files. RSX only gives access to USER 0 to 15.
1-8 Filename (excluding full stop) Always in CAPS and maximum 8 characters long.
9-11 Extension Always in CAPS and maximum 3 characters long. Read Only flag on byte9 bit7. Hidden flag on byte10 bit7. Archive flag on byte11 bit7.
12 Current Extent 0 is first extent. There can be up to 128K bytes (8 logical extents) directly addressed by a single directory entry. Source
13 Reserved
14 Extent High Byte Not used.
15 Record Count (Number of 128 Byte Blocks) Goes up to 128 (&80).
16–31 Block IDs where to find the file data 1 byte is used per 1KB block.


CAT'art

The catalog structure can be hacked by using ascii control characters (codes 0 to 31) to create decorated catalogs (CAT'art).

CAT never loads and executes a boot sector. It just displays the chars of the files using "TXT OUTPUT" (#bb5a) which will execute control codes as well.

There were already tools from the 80ies for modifying a directory in a way that will display colourful chars placed at any location on the screen by adding dummy file entries with 0KB sizes. Or you hardcode it directly by yourself, which allows much more chars and effects.

The trick is to disable text output at the end of a filename to prevent printing file sizes/line feeds and enable it again at the beginning of the next filename; and you also have to use one hidden char for sorting them in the correct order.

See here for more details: All about CAT'arts creation (FR)


CP/M terminology

Record: The basic unit of data access in CP/M, 128 bytes in size. This was the standard size for transferring data between memory and disk.

Block: A group of records, 1 KB in size. Blocks were used to improve disk access efficiency by reading/writing multiple records at once.

Extent: A group of blocks, 16 KB in size. CP/M used extents to manage file allocation, with each extent corresponding to a portion of a file on disk.

Sector: The smallest physically addressable unit on a disk, 512 bytes in size on Amstrad CPC. CP/M accessed the disk at the sector level, though users typically worked with records.


File Headers

Cassette files are divided into 2KB blocks (then subdivided in 256-byte segments + CRC), each block being preceded by a 64-byte header.

AMSDOS files are usually stored with a 128-byte AMSDOS Header (based on cassette header) but can also be headerless, depending on the contents of the file. Unprotected ASCII files do not have header.

CP/M files do not have headers.


Custom floppy disk formats

Usually single sided 40-track 3" disk drives are used in CPCs. For practical purposes, 42 tracks could be used — the limit is specific to the drive and some support more tracks but 42 is a good maximum.

RSX programs exist on top of AMSDOS to get up to 208 KB of usable space per side, by using 42 tracks with 10 sectors per track.


The FDC controller can be used to control 80-tracks and/or double sided drives, though AMSDOS doesn't support such formats. To use 80-track drives and/or dual-head drives, you need to use another CPC DOS instead of AMSDOS. The most popular one is ParaDOS. It can handle up to 796 KB instead of 178 KB for AMSDOS and it supports 22 different disk file formats, including the three standard AMSDOS ones.

Supported Formats in ParaDOS
Format Capacity Catalog Type Sectors/Track Sectors
PARADOS 80 396k 128 SS 10 &91-&9a
PARADOS 41 203k 64 SS 10 &81-&8a
PARADOS 40D 396k 128 DS 10 &a1-&aa
ROMDOS D1 716k 128 DS 9 &01-&09
ROMDOS D2 712k 256 DS 9 &21-&29
ROMDOS D10 796k 128 DS 10 &11-&1a
ROMDOS D20 792k 256 DS 10 &31-&3a
ROMDOS D40 396k 128 SS 10 &51-&5a
S-DOS 396k 128 SS 10 &71-&7a
DATA (SS 40) 178k 64 SS 9 &c1-&c9
DATA (DS 40) 356k 64 DS 9 &c1-&c9 E
DATA (SS 80) 356k 64 SS 9 &c1-&c9 E
DATA (DS 80) 716k 64 DS 9 &c1-&c9 E
SYSTEM (SS 40) 169k 64 SS 9 &41-&49
SYSTEM (DS 40) 346k 64 DS 9 &41-&49 E
SYSTEM (SS 80) 346k 64 SS 9 &41-&49 E
SYSTEM (DS 80) 704k 64 DS 9 &41-&49 E
IBM (SS 40) 169k 64 SS 8 &01-&08
IBM (DS 40) 346k 64 DS 8 &01-&08 E
IBM (SS 80) 346k 64 SS 8 &01-&08 E
IBM (DS 80) 704k 64 DS 8 &01-&08 E
ULTRAFORM 203k 64 SS 9 &10-&19

Legend: SS = Single-Sided, DS = Double-Sided.

Half of the original AMSDOS rom is occupied by Dr. Logo from Digital Research. If you replace AMSDOS with ParaDOS, you will lose access to Dr. Logo.

There is also a special version of ParaDOS, called VaraDOS, that supports the Vortex Format.

UniDOS goes beyond and supports various mass-storage expansions, but also includes support for AMSDOS/ParaDOS floppy discs and tape.


FDC Track Format

The 765 FDC only supports the single-density IBM 3740 track format and the double-density IBM System/34 track format, which are the defacto standards for floppy disks in most computer systems. These formats have been created by an IBM engineer named Alan Shugart (not to be confused with Amstrad's CEO, Alan Sugar).

FDC765 - FM and MFM.png

On Amstrad CPC, the MFM MODE pin of the FDC is not connected. So the FM mode is unusable.

On Amstrad CPC, an MFM track contains about 6250 raw bytes: 200 ms per track (at 300rpm) / 32 µs per byte (with a bit cell of 4µs). Fun fact: You can squeeze a few more bytes on disk by using a floppy drive that spins a little slower, and counting on the tolerance of the FDC to make that disk readable on unmodified floppy drives.

Notes:

  • IAM signifies the beginning of a track.
  • IDAM marks the beginning of a sector's header.
  • DAM (or DDAM) marks the beginning of the actual data in a sector. Deleted data sectors are marked by an F8 byte instead of an FB byte.
  • In MFM encoding, IDAM and DAM are always preceded by three A1 bytes to help the FDC lock onto the data stream after a gap and accurately read the following datas. This is needed because MFM is more compact and harder to read than earlier encoding methods.
  • Gaps are necessary to accommodate variations in rotation speed between different drives and avoid overlapping.

The main competitor of the µPD765 FDC chip on the market was the WD179x FDC chip family. The primary difference between 765 and 179x controllers is that the 765 only does standard track formats (preamble, marks and data fields), while the 179x will write anything you tell it in the write track (formatting a track) mode.


Gaps Protection

Gaps was a common method of protecting floppy disks against copying on the Amstrad CPC, particularly with French software houses such as Infogrames and Loriciels. It consists of writing specific values (other than the standard &4E) in the separation area between 2 consecutive sectors.

When the protected program is launched, it checks if these special values (most often a string signature) are present. If they aren't, the program can then crash or reset the computer or format the disk – or in the case of some games, the player can play the game, but it will crash or freeze at some point.

The trick is that the 765 FDC can read the custom byte values in the gaps, but it cannot write them. This made it hard for people to make working copies of protected disks.


Weak Sectors Protection

Another common copy-protection scheme was using (fully or partially) unmagnetized sectors. The unmagnetized data would then appear as random values when read by the FDC.

When the protected program is launched, it reads these weak sectors multiple times. Due to their unstable nature, these sectors will return different data on each read. If the program detects this changing data, it recognizes the disk as an original and continues to run. If not, the program can then crash, reset the computer, etc.

The trick is that the FDC cannot unmagnetize portions of a sector or leave portions of a sector unmagnetized to recreate this effect on another floppy disk.


Error Detection

The FDC765 happens to use the exact same algorithm for error detection as the one the Amstrad firmware uses to check each 256-byte tape segments.

The CRC error-detecting code is initialised to &FFFF. It is updated byte by byte and uses the CCITT-CRC16 algorithm. It is written after the ID and data fields of each sector in big-endian format (high byte first and then low byte).


FM Encoding

FM (Frequency Modulation) encoding was one of the earliest methods used to store data on floppy disks by creating changes in the magnetic field, known as flux transitions, to represent binary data.

In FM encoding, each bit of data is divided into two distinct parts: a clock signal and a data signal. The clock signal is always present to indicate the timing, while the data signal only appears when the bit is a 1, and remains absent when the bit is a 0.

This constant clock pulse ensures that the FDC always knows where each bit begins and ends. For every bit of information written to the disk, there’s always one clock signal and, if the data is a 1, a data signal as well.

FM encoding scheme.png

Legend: C=Clock, D=Data


MFM Encoding

MFM (Modified Frequency Modulation) was developed as a more efficient alternative to FM encoding. This method greatly reduces the number of transitions needed to represent data compared to FM.

If a cell contains a 1, the signal will be recorded in the middle of the cell. If a cell contains a 0, the signal will be recorded at the beginning of the cell, unless it was preceeded by a cell with a 1. If a signal is transmitted for a 0 cell, it is used as clock signal.

This clever encoding eliminates the need for separate clock signals for every bit, as they are implied by the data pattern. It allows the recording of double the density compared to FM without increasing the bit rate on the floppy material. Each bit cell has only half the size compared to FM.

MFM encoding scheme.png


HD Floppy Disks on CPC

It is theoretically possible to use HD floppy disks (1.44MB) on CPC by using either a Gotek drive or Amiga HD floppy drives spinning at 150rpm. However, nobody has ever written a CPC DOS to make use of it.

On a real floppy drive, if you want to fit more sectors on the same track, you have 2 options: you can make the FDC run faster, or you can make the disk spin slower.

Normally, HD disks use a faster FDC (with an automatic switch between the slow and fast modes).

But, for example on Amiga systems with HD drives, they used floppy drives that spin slower for HD disks (150 rotations per minutes instead of 300) and this allow to use the same controller as before. By the time the floppy has done one complete rotation, you can write 18 sectors instead of just 9.

With a real PC HD floppy drive, this requires some mechanical modifications, and you may get into trouble if the spinning speed is not fast enough.

But with the Gotek, this is not a problem. You can have as many sectors as you want, and the Gotek will generate the index pulse (simulating the floppy completing a turn) after it has sent them all. So it is essentially emulating a floppy that turns very slowly. The FDC has no problems handling that, but you may need to be a bit more relaxed than usual with the timeouts, as it will be some time before the sector you need will pass in front of the drive head, and the index pulse will also be slower than usual.

On a Gotek drive, you can even simulate fantasy floppy disks with up to 255 cylinders, and the FDC will handle them perfectly fine.


Mass Storage via FDC

The Gotek drive (with a FlashFloppy or HxC firmware) has a special direct access mode that allows it to be used as a poor's man hard drive, offering access to up to 32 GB of storage space. It is accessible via the track 255. Source

This is a great feature as it alleviates the need for another mass storage expansion. And the relative slowness of this solution (~15 KB/s) compared to a proper mass storage device (~130 KB/s with Symbiface II) is not much of an issue on Amstrad CPC.

This special Gotek direct access mode is supported in SymbOS. Source


FDC Block Diagram

The FDC chip is quite different from the other CPC chips. It contains its own internal CPU, ROM and RAM.

WDC37C65 block diagram.png


Internal details of the chip

Internally this is a microcoded part with a primative controller of NEC’s own design.

Testing microcode embedded in a part can be troublesome. The uPD765 had a few extra gates associated with the DMA Request and DMA Ack pins.

Presenting a certain illegal combination here places the part into a “test” mode and allows the sequencer microcode to be output on the normal Data pins. The sequencer microcode is responsible for high level commands such as Read Track, Recalibrate, Format Track, or Write Data.

There is a similar test mode for the nano-code array which serializes data at the floppy disk head. Source


Intel 8272 FDC

NEC uPD765 (or just D765) is exactly the same chip as the 8272. NEC and Intel cross-licensed a bunch of IP back in the day. Source

The 8272/µPD765 was the result of a cross-licensing deal between NEC and Intel. It was essentially NEC design. Source

The decapped photos of Intel 8271, NEC D765 and Intel 8272 chips prove that NEC D765 and Intel 8272 chips are identical.


Generic System Diagram

The Amstrad CPC and Amstrad Plus do not have a DMA controller associated with the FDC. And the clock runs at 4MHz instead of 8MHz.

FDC765 - System Diagram.png


Unconnected Pins

The DRQ (14), INT (18), VCO SYNC (24), MFM MODE (26), US1 (28), and HEAD LOAD (36) pins are not connected. The TC (16) and RESET (1) pins are connected together. Source

At the end of a successful read or write command, the program should send a Terminal Count (TC) signal to the FDC. However, in the CPC the TC pin isn't connected to the I/O bus, making it impossible for the program to confirm a correct operation. For that reason, the FDC will assume that the command has failed, and it'll return both Bit 6 in Status Register 0 and Bit 7 in Status Register 1 set. The program should ignore this error message.

The CPC doesn't support floppy DMA transfers, and the FDC's Interrupt signal isn't used in the CPC.

The FDC controller inside the CPC or in the Amstrad DDI-1 expansion doesn't have the US1 pin connected. This means it can only select floppy drives 0 and 1, and not drives 2 and 3. And AMSDOS supports a maximum of two disk drives only.

However, the FDC in the Vortex disc interface does have the US1 pin connected, and so it can manage up to 4 floppy drives.


ABBA switch

The ABBA switch is a common hardware modification that allows users to swap between Drive A and Drive B.

On Amstrad CPC, some games and other software were designed to run specifically from Drive A, creating a problem when the disk you needed was in Drive B.

The ABBA switch resolved this issue by allowing you to "swap" the designation of the two drives. When the switch is activated, Drive A becomes Drive B, and vice versa, effectively swapping their roles.


PC to CPC floppy connector

Cpc6128floppytopcfloppy.gif


Ready / Disk Changed signal

This signal differs between floppy drives model:

  • For 3inch floppy drives, it is a "Ready" signal (pin 26). The /RDY signal turns on when a disk is inserted and spinning in the drive, usually after detecting 2 or 3 index pulses, depending on the drive model. It turns off immediately if the disk is removed or the motor stops.
  • For PC 3.5inch floppy drives, it is a "Disk Changed" signal (pin 34). The /DSKCHG signal determines whether the same disk loaded during the previous disk access is still in the drive.

The easiest solution to this issue is to force the Ready signal on the cable. However, the CPC will hang if you type the CAT command with no disk inserted (inserting a disk will unblock it).

Alternatively, you can Modify PC floppy drives to create a Ready signal, or use Amiga floppy drives, which already have this signal.

Gotek drives with FlashFloppy or HxC firmware can also be configured to simulate the Ready signal. Don't forget to use a proper floppy drive cable then, not the one commonly sold by CPC hobbyists with the Ready signal forced.


PC Floppy Drive types

The IBM PC supports 3 standard diskette formats on a 5.25 inch drive:

  • The earliest IBM PCs used single-sided, double density, 40 cylinders, 300 RPM, floppy drives which yield a capacity of 160 KB per side. And MS-DOS 1.0 only supported single-sided floppy drives.
  • Double-sided floppy drives were introduced in the IBM PC in 1982 and are supported in MS-DOS 1.1. They originally had a capacity of 320 KB per diskette. MS-DOS 2.0 extended the capacity to 360 KB with a new disk format. Source
  • A new floppy drive was introduced with the PC/AT in 1984. It is double sided, quad density, 80 cylinders, with a total capacity of 1.2 MB. The high density drive rotates at 360 RPM, so only 15 sectors can be written on a track instead of 18.

The IBM PS/2 introduced two standard 3.5 inch diskette formats:

  • The first is a double sided, double density, 80 cylinders, format yielding a capacity of 720KB. The double density drive rotates at 300 RPM.
  • The other is double sided, quad density, 80 cylinders, with a total capacity of 1.44 MB. The high density drive rotates at 300 RPM.

Fun fact: The original IBM PC didn’t have a hard drive, even as an option. And MS-DOS 1.x didn't have any support for hard drives either. Hard drives only became a thing with the introduction of the IBM PC/XT and MS-DOS 2.0 in 1983. But the floppy drive was not the only option to load programs on the original IBM PC. You could also use a tape deck, just like on Amstrad CPC. However, the tape port disappeared with the PC/XT. Source


FDD Block Diagram

Floppy Disk Drive - Block Diagram.png


Chip Variants

NEC has developed various successors to the original uPD765, such as the uPD72065, uPD72067, and uPD72069.

Intel has also produced successors of the 8272, such as the 82072, 82077 and 82078.


Datasheets


External links

Retrieved from "https://gryzor.info/index.php?title=765_FDC&oldid=119941"