Amstrad/Schneider Printer Buttons and DIP Switches
From CPCWiki - THE Amstrad CPC encyclopedia!
Revision as of 07:23, 4 September 2010 by Nocash (Talk | contribs) (Created page with "== DIP Switch Settings == {|{{Prettytable|width: 700px; font-size: 2em;}} |colspan=5|'''DMP1 DIP Switches''' |- | ||''Function''||''Off = High = 1''||''On = Low = 0''||''Softwar...")
DIP Switch Settings
| DMP1 DIP Switches | ||||
| Function | Off = High = 1 | On = Low = 0 | Software | |
| DS1-1 | International characters Bit0 |
7=off:off:off=USA (default) |
Cannot be changed by software | |
| DS1-2 | International characters Bit1 | |||
| DS1-3 | International characters Bit2 | |||
| DS1-4 | CR Function | CR only (default) | CR & LF | Affects chr(0Dh) |
| NLQ401 DIP Switches | ||||
| Function | Off = High = 1 | On = Low = 0 | Software | |
| DS1-1..8 | Reserved | DS1 is not installed, DS1-1..7 floating (without pull-up), DS1-8 hardwired to GND (On) | ||
| DS2-1 | Page length | 11 inch (default) | 12 inch | Can be also changed via ESC "C" (at least on Epsons, no idea if on NLQ401, too?) |
| DS2-2 | International characters Bit0 |
0=on:on=France |
Can be also changed via software ? | |
| DS2-3 | International characters Bit1 | |||
| DS2-4 | Zero character | Slashed (default) | Unslashed | Affects chr(30h) |
| DS2-5 | 1 inch skip perforation | Invalid/Disable (default) | Valid/Enable | Can be also changed via ESC "N"/ESC "O" (at least on Epsons, no idea if on NLQ401, too?) |
| DS2-6 | Not used | Unused | Unused (default) | - |
| DS2-7 | CR Function | CR+LF | CR only (default) | Affects chr(0Dh) |
| DS2-8 | SLCT IN Exchange | External | Internally fixed (default) | ? |
| DMP2000/DMP2160/DMP3000/DMP3160/DMP4000 DIP Switches | ||||
| Function | Off = High = 1 | On = Low = 0 | Software | |
| DS1-1 | International characters Bit0 |
0=USA, 1=France, 2=Germany, 3=United Kingdom, 4=Denmark, 5=Sweden, 6=Italy, 7=Spain |
Can be also changed via ESC "R" | |
| DS1-2 | International characters Bit1 | |||
| DS1-3 | International characters Bit2 | |||
| DS1-4 | CR Function | CR only (default) | CR & LF | Affects chr(0Dh) |
| DS1-5 | Paper out sensor | Enable | Disable | Can be also changed via ESC "8"/ESC "9" |
| DS1-6 | Page length | 11 inch | 12 inch | Can be also changed via ESC "C" |
| DS1-7 DMP2xxx | Code Unit | 8 units (MSB=CentronicsPin9) | On=7 units (MSB=0) "set this for Apple computers" | Can be also changed via ESC "#"/ESC "="/ESC ">" |
| DS1-8 DMP2xxx | Default Character Set | Epson Standard | Epson NLQ | Can be also changed via ESC "x" |
| DS1-7 DMP3xxx,DMP4000 | Default Character Set Bit0 | Charset (3=Epson Standard, 2=Epson NLQ, 1=IBM #1, 0=IBM #3) | Can be also changed via ESC "x" and ESC "m" | |
| DS1-8 DMP3xxx,DMP4000 | Default Character Set Bit1 | |||
| DS2-1 | Zero character | Unslashed | Slashed | Affects chr(30h) |
| DS2-2 | Default skip perforation | Disable | Enable | Can be also changed via ESC "N"/ESC "O" |
| DS2-3 | Buffer mode | Character | Graphics | ? |
| DS2-4 | Buffer mode | Character/Graphics (use DS2-3 setting) | Download (=UserDefCharset) | Must be On for ESC "&" |
| DS2-5 | SLCT IN signal | Not sent | Automatically sent | ? |
| DS2-6 | Alarm beeper | Disable | Enable | Affects chr(07h) and/or Paper-Out alarm (?) |
| DS2-7 | Default typeface | Bold off | Condensed & bold on | ??? |
| DS2-8 | Default typeface | Condensed off | Bold on | ??? |
| DS2-9 | Do not use | |||
| DS2-10 | Do not use | |||
| DMP3250di Extra RS232 DIP-switches | ||||
| DS3-1 | Baudrate Bit0 | 0=9600, 1=4800, 2=2400, 3=1200, 4=600, 5=300, 6=200, 7=150 bps | ||
| DS3-2 | Baudrate Bit1 | |||
| DS3-3 | Baudrate Bit2 | |||
| DS3-4 | Parity On/Off | Enable | Disable | |
| DS3-5 | Parity Even/Odd | Odd | Even | |
| DS3-6 | Data Bits | 7bit | 8bit | |
| DS3-7 | Stop Bits | 1bit | 2bit | |
| DS3-8 | Handshake Bit0 | 0=RTS(Ready/Busy), 1=Série(XON/XOFF), 2=Série(ETX/ACK), 3=Reserved) | ||
| DS3-9 | Handshake Bit1 | |||
| DS3-10 | Interface | Centronics/Parallel | Serial/RS2322 | |
| LQ3500/LQ5000 DIP Switches | ||||
| Function | Off = High = 1 | On = Low = 0 | Software | |
| DS1-1 | International characters Bit0 |
0=USA, 1=France, 2=Germany, 3=United Kingdom, 4=Denmark, 5=Sweden, 6=Italy, 7=Spain |
Can be also changed via ESC "R" | |
| DS1-2 | International characters Bit1 | |||
| DS1-3 | International characters Bit2 | |||
| DS1-4 | Page length | 11 inch | 12 inch | Can be also changed via ESC "C" |
| DS1-5 | Skip perforation | Disable | Enable | Can be also changed via ESC "N"/ESC "O" |
| DS1-6 | Alarm beeper | Disable | Enable | Affects chr(07h) and/or Paper-Out alarm (?) |
| DS1-7 | Default Character Set | Standard/Draft | LQ Letter Quality | Can be also changed via ESC "x" |
| DS1-8 | SLCT IN signal | Not sent | Automatically sent | ? |
| DS2-1 | Paper out sensor | Enable? | Disable? | Can be also changed via ESC "8"/ESC "9" |
| DS2-2 | CR Function | CR only (default) | CR & LF | Affects chr(0Dh) |
| DS2-3 | Zero character | Unslashed | Slashed | Affects chr(30h) |
| DS2-4 | Reserved | - | - | - |
| DS2-5 | Character Set | Epson | IBM#2 | ... |
| DS2-6 | Unused | - | - | - |
| DS2-7 | Auto loading | Enable | Disable | ... |
| DS2-8 | Reserved | - | - | - |
| LQ3500di/LQ5000di Extra RS232 DIP-switches | ||||
| DS3-1 | Baudrate Bit0 | 0=9600, 1=4800, 2=2400, 3=1200, 4=600, 5=300, 6=200, 7=150 bps default = 9600 = all off | ||
| DS3-2 | Baudrate Bit1 | |||
| DS3-3 | Baudrate Bit2 | |||
| DS3-4 | Parity Even/Odd | Odd | Even | |
| DS3-5 | Parity On/Off | Disable | Enable | |
| DS3-6 | Data Bits | 8bit | 7bit | |
| DS3-7 | Handshake Bit0 | 3=off:off=Parallel/Centronics 2=on:off=Serial/XonOff 1=off:on=Serial RTS read/busy 0=on:on=Serial Etx/Ack | ||
| DS3-8 | Handshake Bit1 | |||
