Revision as of 11:57, 20 August 2014

Snapshot (.SNA) file format

The format was first defined for the CPCEMU emulator but is now widely supported. The format was originally defined by Marco Vieth. Version 3 was defined by Ulrich Doewich, Martin Korth, Richard Wilson and Kevin Thacker.

There are 3 versions defined in this document. Version 3 is the most recent and is currently supported by a few of the most recent emulators.

Abbreviations:

• GA = "Gate Array"
• CRTC = "6845 Cathode Ray Tube Controller"
• PPI = "Intel 8255 Programmable Peripheral Interface"
• PSG = "AY-3-8912 Programmable Sound Generator"

Version 1

Notes:

1. All multi-byte values are stored in little-endian format (low byte followed by higher bytes).
2. "IFF0" reflects the state of the maskable interrupt (INT). "IFF1" is used to store the state of IFF0 when a non-maskable interrupt (NMI) is executed. Bit 0 of these bytes is significant. For CPCEMU compatibility, these bytes should be set to "1" when the IFF flip-flop is "1" and "0" when the flip-flop is "0". For compatibility with other emulators, bits 7-1 should be set to "0". When bit 0 of "IFF0" is "0" maskable interrupts will be ignored. When bit 0 of "IFF1" is "1" maskable interrupts will be acknowledged and executed. See the document about the Z80 for more information.
3. This byte will be 0, 1 or 2 for the interrupt modes 0, 1 or 2. The interrupt mode is set using the "IM x" instructions. See the document about the Z80 for more information.
4. These registers are from the alternate register set of the Z80.
5. These registers are 16-bit. "low" indicates bits 7..0, "high"indicates bits 15..8.
6. This byte represents the inputs to PPI port A regardless of the input/output setting of this port.
7. This byte represents the inputs to PPI port B regardless of the input/output setting of this port.
8. This byte represents the outputs from port C regardless of the input/output setting of this port.
9. This byte represents the PPI control byte which defines the input/output and mode of each port and not the last value written to this port. For CPCEMU compatibility bit 7 of this byte must be set to "1".
10. This byte in the snapshot represents the selected pen register of the Gate-Array. This byte is the last value written to this port. Bit 7,6,5 should be set to "0".
11. This byte in the snapshot represents the multi-configuration register of the Gate-Array. This byte is the last byte written to this register. For CPCEMU compatibility, bit 7 should be set to "1" and bit 6 and bit 5 set to "0".
12. These bytes are the current palette. For CPCEMU compatibility, these bytes should have bit 7=bit 6=bit 5="0". Bits 4..0 define the colour using the hardware colour code. The colours are stored in the order pen 0, pen1, pen 2,...,pen 15 followed by border colour.
13. This byte represents a ram configuration for a Dk'Tronics/Dobbertin/Amstrad compatible RAM expansion, or the built in RAM expansion of the CPC6128 and CPC6128+. Bits 5..0 define the ram expansion code. For CPCEMU compatibility, bit 7 and bit 6 of this byte should be set to "0".
14. This byte in the snapshot represents the index of the currently selected CRTC register. For compatibility with CPCEMU this value should be in the range 0-31.
15. These bytes represent the data of the CRTC's registers.
16. This byte in the snapshot represents the last byte written to the "ROM select" I/O port.
17. This byte in the snapshot represents the index of the currently selected PSG register. For CPCEMU compatibility, this byte should be in the range 0-15.
18. the first 64k is always the base 64k of ram. The second 64k (if present) is the additional ram in a Dk'Tronics/Dobbertin/Amstrad compatible RAM expansion or the internal ram of the CPC6128/CPC6128+. The memory dump is not dependant on the current RAM configuration. Note that CPCEMU can only write a 64K or 128K snapshot.

Changes and additions in Version 2 from Version 1

Notes:

1. If standard CPC raster interrupts are used, interrupts are acknowledged and "executed" at the time they are requested, then there will be 6 interrupts executed per screen update cycle.
   • CPCEMU uses a simple system to emulate the interrupts. It is assumed there are exactly 6 interrupts per screen update cycle (the interrupts are assumed to occur at a frequency of 300Hz). This byte records the interrupt number in the current screen update cycle. More accurate emulators use the correct interrupt generation method and may ignore this byte. For CPCEMU compatibility, these emulators should set this byte to "0".
   • CPCEMU uses a simple system to emulate the screen display. It allows the mode to be changed in each of the 6 interrupts that occur during a single 50Hz/60Hz period. These bytes represent the mode in each of these sections, i.e. the screen modes (0,1 or 2) for the interrupts 0..5. More accurate emulators support changing of the screen mode at any point supported by the Amstrad hardware, these emulators should write "0" for all these bytes.

Changes and additions in Version 3 from Version 2

Notes:

1. This byte in the snapshot represents the last byte written to the printer I/O port (this byte does not include the automatic inversion of the strobe caused by the Amstrad hardware).
2. This register is internal to the CRTC and counts the number of character-lines. The counter counts up. This value is in the range 0-127. (This counter is compared against CRTC register 4).
3. This register is internal to the CRTC and counts the number of raster-lines. The counter counts up. This value is in the range 0-31. (This counter is compared against CRTC register 9).
4. This register is internal to the CRTC and counts the number of raster-lines during vertical adjust. The counter counts up. This value is in the range 0-31. This should be ignored if the CRTC is not "executing" vertical. adjust.(This counter is compared against CRTC register 5).
5. This register is internal to the CRTC and counts the number of characters during horizontal sync. This counter counts up. This value is in the range 0-16. This should be ignored if the CRTC is not "executing" horizontal sync. (This counter is compared against CRTC register 3).
6. This register is internal to the CRTC and counts the number of scan-lines during vertical sync. This counter counts up. This value is in the range 0-16. This should be ignored if the CRTC is not "executing" vertical sync. (This counter is compared against CRTC register 3).
7. These bytes define the internal state of the CRTC. Each bit in these bytes represents a state.
8. When VSYNC is active, the CRTC is "executing" vertical sync, and the vertical sync width counter in the snapshot is used.
9. When HSYNC is active, the CRTC is "executing" horizontal sync width counter in the snapshot is used.
10. When Vertical total adjust is active, the CRTC is "executing" vertical total adjust and the vertical total adjust counter in the snapshot is used.
11. This register is internal to the CRTC and counts the number of characters. This counter counts up. This value is in the range 0-255. (This counter is compared against CRTC register 0).
12. This counter is internal to the GA and counts the number of HSYNCs. This counter is used to generate CPC raster interrupts. This counter counts up. This value is in the range 0-51.
13. This flag is "1" if a interrupt request has been sent to the Z80 and it has not yet been acknowledged by the Z80. (A interrupt request is sent by the GA for standard CPC raster interrupts or by the ASIC for raster or dma interrupts).
14. This is a counter internal to the GA and counts the number of HSYNCs since the start of the VSYNC and it is used to reset the interrupt counter to synchronise interrupts with the VSYNC. This counter counts up. This value is between 0 and 2. If this value is 0, the counter is inactive. If this counter is 1 or 2 the counter is active.

Immediatly following the memory dump there is optional data which is seperated into chunks.

Each chunk of data has a header and this is followed by the data in the chunk. The header has the following format:

Notes:

1. The chunks are defined with 4-byte character codes. (e.g. "CPC+"). In this example, the 4-byte character code would be stored in the file as 'C' then 'P' then 'C' then '+'.
2. The "Chunk data length" defines the length of data following the header and does not include the size of the header. This number is stored in little endian format.
3. If a emulator finds a chunk which it does not support then it should skip the chunk and continue with the next chunk in the file. Therefore an emulator author may add emulator specific chunks to the file and it will not prevent the snapshot from being used with other emulators that do not recognise the added chunks.
4. There is not a terminator chunk. The snapshot reader should determine if there are more chunks based on the size of data remaining to be read from the file.

The following chunks are currently defined:

CPC+ Chunk

Chunk name: "CPC+"

Chunk data:

Notes:

1. The sprite data is packed, with two sprite pixels per byte. Bits 7..4 define the first pixel and bits 3..0 define the second pixel.
2. The attributes for each sprite take 8 bytes. Each attribute block has the following format:

Note: the Sprite X, Y and magnification are in the same order as the ASIC registers

3. This is a direct copy of the palette in CPC+ ASIC Ram. There are 32 colours each with 2-bytes per colour.
4. These bytes in the snapshot represent the last value written to these ASIC registers.
5. These bytes represent the inputs to the analogue channels.
6. The attributes for each DMA channel take 4 bytes. Each attribute block has the following format:

Note: the DMA address and prescalar are in the same order as the ASIC registers.

7. These registers are internal to the CPC+ and define the current DMA operation:

a.) This value represents the number of loops remaining. 0 = none. This count is between 0..0FFF. This counter counts down.
b.) This is the Amstrad memory address to loop back to. It is a pointer to the DMA instruction after the last REPEAT instruction.
c.) This value represents the pause count and the count is between 0...0FFF. (TO BE CHECKED: down counter? what exactly does it represent)
d.) This value represents the pause prescalar count and the count is between 0..FF. (TO BE CHECKED: down counter? what exactly does it represent)

8. This value represents the last value written to this I/O port.
9. This value represents the lock status of the ASIC. If the ASIC is un-locked then the advanced features and ASIC registers are accessible.
10. This value represents the current unlock sequence state.

Memory blocks =

Chunk name: MEM0-MEM8. 64K per block.

MEM0 for Standard 64k. MEM1 to MEM8 for memory expansion bank.

These will exist if the memory has been compressed.

A RLE compression is used with 0x0e5 as the control byte.

Example:

11 22 33 = 11 22 33 E5 03 11 = 11 11 11 E5 00 = E5