Difference between revisions of "Aleste 520EX - I/O Ports"

Revision as of 04:05, 11 February 2010

I/O Ports for Aleste 520EX

I/O Map (Overview)

Ext Port

Aleste Gate Array (aka Patasonic's Multiport)

Aleste "Gate Array" is similar in functionality to the Gate-Array in the CPC/Plus.

Gate Array Register 0

Pen index:

Gate Array Register 1

The number is converted by IC D62.

• When MAPPER is set in EXTPORT, then the numbers effectively define a R,G,B colour with 2 bits per element, but the rom then changes the order of the bits before it gets to the hardware.
• When MAPPER is not set, the number is equivalent to the CPC's Gate-Array colour value, but this is looked up in IC D62 and converted into a 2-bit per element R,G,B for the aleste video hardware.

Gate Array Register 2

bit 0,1 define the mode. The actual resolution is then dependant on bit 1 of EXTPORT. When HIGHTX is 0, CPC modes are chosen. When HIGHTX is 1, Aleste modes are chosen.

CPC modes:

Aleste modes:

Gate Array Register 3 (in CPC-style MAPMOD=0)

Controls RAM Banking, similar to the Gate Array on CPC6128 (or, more specific, similar to the 16L8 PAL IC which assists the CPC6128s Gate Array).

In the Aleste register 3 is effectively Mapper select.

Writing to port #7Fxx with bit 7 and bit 6 of data set to 1 can be used to set page 3 RAM bank in Aleste mapper mode, or to define CPC RAM configuration in CPC mode.

Actually, it seems to work more like an Inicron RAM-Box (which isn't fully compatible with the dk'tronics style Standard Memory Expansions).

Gate Array Register 3 (in Aleste's special MAPMOD=1)

Four I/O ports control the mapper:

The decoding of the I/O port for the mapper uses bit 15 of the I/O address in the same way as the Aleste "Gate Array".

Bit 9,8 define which page.

To avoid writing to the Aleste "Gate-Array" bits 7 and 6 of the data must be 1.

The remaining bits define the RAM block/configuration to use.

In CPC mode, writing to the mapper changes the RAM configuration for all pages, with the memory configuration being the same as a DK'Tronics compatible RAM.

In Aleste mapper mode, writing to the mapper changes the RAM for one page.

It is not know:

• Must you write to #7Fxx in CPC mode to define RAM configuration or can you also use #7Cxx, #7Dxx, #7Exx for same effect
• When you write CPC RAM configuration is it mirrored in all mapper registers?

Upper ROM Bank

Works like the Upper ROM Bank Number on CPCs. The banks used for the Aleste BIOS are:

 00h BASIC    (bytes in 4000h..7FFFh in the Aleste's 64K EPROM)
 03h BOOTMENU (bytes in C000h..FFFFh in the Aleste's 64K EPROM)
 07h AMSDOS   (bytes in 8000h..BFFFh in the Aleste's 64K EPROM)

All other values 01h..02h, 04h..06h, 08h..FFh do select BASIC, too.

PPI 8255

Works similar to the 8255 in the CPC (see there for details). Differences are listed below.

PPI Port A (Port F4xxh)

PPI Port B (Port F5xxh)

PPI Port C (Port F6xxh)

PPI Control (Port F7xxh)

This register has two different functions depending on bit7 of the data written to this register.

See the normal CPCs 8255 description for details.

Keyboard

The Aleste uses a MSX keyboard, as seen by the characteristic five function keys. The mainboard contains some excessive TTL logic, assisted by the upper data bits of the VDKEY eprom, that translates the MSX matrix to a CPC matrix.

So, at I/O port level, the CPU "sees" a CPC matrix, not a MSX matrix. When running MSXDOS, this leads to the funny situation that MSXDOS must undo the hardware MSX-to-CPC translation by some software CPC-to-MSX translation.

The keyboard has some additional keys, which aren't on normal CPC keyboards:

• F1/F6, F2/F7, F3/F8, F4/F9, F5/F10 - MSX-style function keys, mapped to keyboard row 10, bits 7,6,5,4,3.
• HELP, INS, b - additional keys, mapped to keyboard row 10, bits 2,1,0.
• R/L - Russian/Latin mode, mapped to keyboard row 9, bit6 (aka joystick Fire3).
• RES - Reset button, goes to /RESET signal.
• Four unknown keys - These keys (above the numeric keypad) may be unused, or having same function as other keys?

The Aleste has a JCUKEN keyboard, rather than a QWERTY keyboard.

• Unknown if this done by hardware, or by patched CPC bios (?)
• Normally, the key next to TAB should be Row8.Bit3 in the CPC matrix. And the BIOS should assign "Q" to it for english QWERTY keyboards, "A" for french "AZERTY" keyboards - or "J" for russian JCUKEN keyboards (though not sure if Patisonic has implemented it that way).

 _____ _____ _____ _____ _____                 _____ _____ _____   _____ _____
|F1/6 |F2/7 |F3/8 |F4/9 |F5/10|               |HELP |INS  | DEL | |N/A  | RES |
|_____|_____|_____|_____|_____|               |_____|_____|_____| |_____|_____|
 _____ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ _____   ___ ___ ___
| ESC | ; | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | _ | b |  BS | |N/A|N/A|N/A|
|_____|___|___|___|___|___|___|___|___|___|___|___|___|___|_____| |___|___|___|
|  TAB  | J | C | U | K | E | N | G | { | } | Z | H | : | / |   | | F7| F8| F9|
|_______|___|___|___|___|___|___|___|___|___|___|___|___|___|   | |___|___|___|
|  CTRL  | F | Y | W | A | P | R | O | L | D | V | \ | . |RETURN| | F4| F5| F6|
|________|___|___|___|___|___|___|___|___|___|___|___|___|______| |___|___|___|
|CAPS| R/L | Q | | | S | M | I | T | X | B | @ | '  |   | U |   | | F1| F2| F3|
|____|_____|___|___|___|___|___|___|___|___|___|____| L |___| R | |___|___|___|
|  SHIFT | COPY|         SPACE              | SHIFT |   | D |   | | F0| F.|ENT|
|________|_____|____________________________|_______|___|___|___| |___|___|___|

Aleste 8bit Printer Port

• Printer data-bits are connected to AY I/O port B (PSG register 15).
• Printer strobe is connected to PPI 8255 port C bit 4. The strobe is negated by the hardware.
• Printer busy is connected to PPI 8255 port B bit 6.
• All of the above PPI and PSG registers are bi-directional.

This is different as that in the CPC (the CPCs Printer Port uses Port EFXXh for one-directional 7bit data plus strobe).

Joystick

The Aleste has a 7pin joystick connector. Aside from the different pin-outs, it's the same as the normal 9pin connector on CPCs. Except that:

• There's no COM2 signal (no way to attach an Y-cable for 2nd joystick to the connector)
• There's no FIRE3 signal (which is undocumented, rarely used pin on CPC) (NB. The Aleste uses FIRE3 as R/L key on the keyboard).

Mouse

The built-in RS232 port can be used to connect a serial mouse.

• See Serial RS232 Mouse for details on the protocol

Translation PROMs and EPROMs

• Aleste Translation PROMs and EPROMs - description of the numbers in the look-up PROMs/EPROMs