Difference between revisions of "SYMBiFACE II:IDE registers"
From CPCWiki - THE Amstrad CPC encyclopedia!
| (12 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
| − | This is the documentation about the '''IDE registers''' of the [[SYMBiFACE II]] expansion card | + | The Symbiface 2 operates the ATA/IDE device in 16-bit data transfer mode. 16-bits of data is buffered at a time within the Symbiface 2 and read/written via the Data port I/O address 8 bits at a time. The device was designed when devices didn't support ATA CFA command set and 8-bit PIO data transfer so this is why it buffers 16-bit of data. (16-bits is the "native" data transfer of an ATA device). |
| + | |||
| + | The I/O ports operate in a "pass-through" like mode where the registers directly reflect those of the connected ATA device. | ||
| + | |||
| + | The [[X-Mass]] is a more modern ATA/IDE device which is compatible with the Symbiface 2 IDE registers and uses the same I/O ports. | ||
| + | |||
| + | This is the documentation about the '''IDE registers''' of the [[SYMBiFACE II]] expansion card. | ||
{|{{Prettytable|width: 700px; font-size: 2em;}} | {|{{Prettytable|width: 700px; font-size: 2em;}} | ||
| Line 10: | Line 16: | ||
|'''#FD08''' || Data Register || Data Register | |'''#FD08''' || Data Register || Data Register | ||
|- | |- | ||
| − | |'''#FD09''' || Error Register || ''(Write Precomp Reg.)'' | + | |'''#FD09''' || Error Register || Features Register/''(Write Precomp Reg.)'' |
|- | |- | ||
| − | |'''#FD0A''' || Sector Count || Sector Count | + | |'''#FD0A''' || Sector Count (0=256) || Sector Count (0=256) |
|- | |- | ||
| − | |'''#FD0B''' || Sector Number || Sector Number | + | |'''#FD0B''' || Sector Number for CHS or LBA bits 0-7 || Sector Number for CHS or LBA bits 0-7 |
|- | |- | ||
| − | |'''#FD0C''' || Cylinder Low || Cylinder Low | + | |'''#FD0C''' || Cylinder Low for CHS or LBA bits 8-15 || Cylinder Low for CHS or LBA bits 8-15 |
|- | |- | ||
| − | |'''#FD0D''' || Cylinder High || Cylinder High | + | |'''#FD0D''' || Cylinder High for CHS or LBA bits 16-23 || Cylinder High for CHS or LBA bits 16-23 |
|- | |- | ||
| − | |'''#FD0E''' || | + | |'''#FD0E''' || Device/Head Register (Bit 6=0 CHS, Bit 6=1 LBA) (Bit 4 = 0 Master, Bit 4 = 1 Slave) (Bits 3..0 Head for CHS or LBA bits 24-27) || Device/Head Register (Bit 6=0 CHS, Bit 6=1 LBA) (Bit 4 = 0 Master, Bit 4 = 1 Slave) (Bits 3..0 Head for CHS or LBA bits 24-27) |
|- | |- | ||
|'''#FD0F''' || Status Register || Command Register | |'''#FD0F''' || Status Register || Command Register | ||
| Line 29: | Line 35: | ||
* [[SYMBiFACE II:IDE routines|Low level IDE routines]] | * [[SYMBiFACE II:IDE routines|Low level IDE routines]] | ||
* [[Programming:SYMBiFACE_II|SYMBiFACE II documentations]] | * [[Programming:SYMBiFACE_II|SYMBiFACE II documentations]] | ||
| − | * | + | * [http://www.t13.org/documents/UploadedDocuments/project/d1153r18-ATA-ATAPI-4.pdf ATA/IDE-specification] |
[[Category:Programming]] | [[Category:Programming]] | ||
Latest revision as of 04:52, 15 January 2018
The Symbiface 2 operates the ATA/IDE device in 16-bit data transfer mode. 16-bits of data is buffered at a time within the Symbiface 2 and read/written via the Data port I/O address 8 bits at a time. The device was designed when devices didn't support ATA CFA command set and 8-bit PIO data transfer so this is why it buffers 16-bit of data. (16-bits is the "native" data transfer of an ATA device).
The I/O ports operate in a "pass-through" like mode where the registers directly reflect those of the connected ATA device.
The X-Mass is a more modern ATA/IDE device which is compatible with the Symbiface 2 IDE registers and uses the same I/O ports.
This is the documentation about the IDE registers of the SYMBiFACE II expansion card.
| Port | Read | Write |
| #FD06 | Alternate Status | Digital Output |
| #FD07 | Drive Address | (Not Used) |
| #FD08 | Data Register | Data Register |
| #FD09 | Error Register | Features Register/(Write Precomp Reg.) |
| #FD0A | Sector Count (0=256) | Sector Count (0=256) |
| #FD0B | Sector Number for CHS or LBA bits 0-7 | Sector Number for CHS or LBA bits 0-7 |
| #FD0C | Cylinder Low for CHS or LBA bits 8-15 | Cylinder Low for CHS or LBA bits 8-15 |
| #FD0D | Cylinder High for CHS or LBA bits 16-23 | Cylinder High for CHS or LBA bits 16-23 |
| #FD0E | Device/Head Register (Bit 6=0 CHS, Bit 6=1 LBA) (Bit 4 = 0 Master, Bit 4 = 1 Slave) (Bits 3..0 Head for CHS or LBA bits 24-27) | Device/Head Register (Bit 6=0 CHS, Bit 6=1 LBA) (Bit 4 = 0 Master, Bit 4 = 1 Slave) (Bits 3..0 Head for CHS or LBA bits 24-27) |
| #FD0F | Status Register | Command Register |
