View source for Amstrad/Schneider Printer Buttons and DIP Switches

== DIP Switch Settings ==

{|{{Prettytable|width: 700px; font-size: 2em;}}
|colspan=5|'''DMP1 DIP Switches'''
|-
| ||''Function''||''Off = High = 1''||''On = Low = 0''||''Software''
|-
|DS1-1||International characters Bit0||colspan=2 rowspan=3|
7=off:off:off=USA (default)<br>
6=off:off:on=France<br>
5=off:on:off=Germany<br>
4=off:on:on=Italy<br>
3=on:off:off=United Kingdom<br>
2=on:off:on=Denmark<br>
1=on:on:off=Sweden<br>
0=on:on:on=Spain
|rowspan=3|Cannot be changed by software
|-
|DS1-2||International characters Bit1
|-
|DS1-3||International characters Bit2
|-
|DS1-4||CR Function||CR only (default)||CR & LF||Affects chr(0Dh)
|-
|}


{|{{Prettytable|width: 700px; font-size: 2em;}}
|colspan=5|'''NLQ401 DIP Switches'''
|-
| ||''Function''||''Off = High = 1''||''On = Low = 0''||''Software''
|-
|DS1-1..8||Reserved||colspan=3|DS1 is not installed, DS1-1..7 floating (without pull-up), DS1-8 hardwired to GND (On)
|-
|DS2-1||Page length||11 inch (default)||12 inch||Can be also changed via ESC "C" (at least on Epsons, no idea if on NLQ401, too?)
|-
|DS2-2||International characters Bit0||colspan=2 rowspan=2|
0=on:on=France<br>
1=on:off=Germany<br>
2=off:on=United Kingdom<br>
3=off:off=USA (default)
|rowspan=2|Can be also changed via software ?
|-
|DS2-3||International characters Bit1
|-
|DS2-4||Zero character||Slashed (default)||Unslashed||Affects chr(30h)
|-
|DS2-5||1 inch skip perforation||Invalid/Disable (default)||Valid/Enable||Can be also changed via ESC "N"/ESC "O" (at least on Epsons, no idea if on NLQ401, too?)
|-
|DS2-6||Not used||Unused ||Unused (default)|| -
|-
|DS2-7||CR Function||CR+LF||CR only (default)||Affects chr(0Dh)
|-
|DS2-8||SLCT IN Exchange||External||Internally fixed (default)||?
|-
|}

{|{{Prettytable|width: 700px; font-size: 2em;}}
|colspan=5|'''DMP2000/DMP2160/DMP3000/DMP3160/DMP4000 DIP Switches'''
|-
| ||''Function''||''Off = High = 1''||''On = Low = 0''||''Software''
|-
|DS1-1||International characters Bit0||colspan=2 rowspan=3|
0=USA,
1=France,
2=Germany,
3=United Kingdom,
4=Denmark,
5=Sweden,
6=Italy,
7=Spain
|rowspan=3|Can be also changed via ESC "R"
|-
|DS1-2||International characters Bit1
|-
|DS1-3||International characters Bit2
|-
|DS1-4||CR Function||CR only (default)||CR & LF||Affects chr(0Dh)
|-
|DS1-5||Paper out sensor||Enable||Disable||Can be also changed via ESC "8"/ESC "9"
|-
|DS1-6||Page length||11 inch||12 inch||Can be also changed via ESC "C"
|-
|DS1-7 DMP2xxx||Code Unit||8 units (MSB=CentronicsPin9)||On=7 units (MSB=0) "set this for Apple computers"||Can be also changed via ESC "#"/ESC "="/ESC ">"
|-
|DS1-8 DMP2xxx||Default Character Set||Epson Standard||Epson NLQ||Can be also changed via ESC "x"
|-
|DS1-7 DMP3xxx,DMP4000||Default Character Set Bit0||colspan=2 rowspan=2|Charset (3=Epson Standard, 2=Epson NLQ, 1=IBM #1, 0=IBM #3)||rowspan=2|Can be also changed via ESC "x" and ESC "m"
|-
|DS1-8 DMP3xxx,DMP4000||Default Character Set Bit1
|-
|DS2-1||Zero character||Unslashed||Slashed||Affects chr(30h)
|-
|DS2-2||Default skip perforation||Disable||Enable||Can be also changed via ESC "N"/ESC "O"
|-
|DS2-3||Buffer mode||Character||Graphics||?
|-
|DS2-4||Buffer mode||Character/Graphics (use DS2-3 setting)||Download (=UserDefCharset)||Must be On for ESC "&"
|-
|DS2-5||SLCT IN signal||Not sent||Automatically sent||?
|-
|DS2-6||Alarm beeper||Disable||Enable||Affects chr(07h) and/or Paper-Out alarm (?)
|-
|DS2-7||Default typeface||Bold off||Condensed & bold on||???
|-
|DS2-8||Default typeface||Condensed off||Bold on||???
|-
|DS2-9||Do not use|| || ||
|-
|DS2-10||Do not use|| || ||
|-
|colspan=5|'''DMP3250di Extra RS232 DIP-switches'''
|-
|DS3-1||Baudrate Bit0||colspan=2 rowspan=3|0=9600, 1=4800, 2=2400, 3=1200, 4=600, 5=300, 6=200, 7=150 bps
|-
|DS3-2||Baudrate Bit1
|-
|DS3-3||Baudrate Bit2
|-
|DS3-4||Parity On/Off||Enable||Disable
|-
|DS3-5||Parity Even/Odd||Odd||Even
|-
|DS3-6||Data Bits||7bit||8bit
|-
|DS3-7||Stop Bits||1bit||2bit
|-
|DS3-8||Handshake Bit0||colspan=2 rowspan=2|0=RTS(Ready/Busy), 1=Série(XON/XOFF), 2=Série(ETX/ACK), 3=Reserved)
|-
|DS3-9||Handshake Bit1
|-
|DS3-10||Interface||Centronics/Parallel||Serial/RS2322
|-
|}

{|{{Prettytable|width: 700px; font-size: 2em;}}
|colspan=5|'''LQ3500/LQ5000 DIP Switches'''
|-
| ||''Function''||''Off = High = 1''||''On = Low = 0''||''Software''
|-
|DS1-1||International characters Bit0||colspan=2 rowspan=3|
0=USA,
1=France,
2=Germany,
3=United Kingdom,
4=Denmark,
5=Sweden,
6=Italy,
7=Spain
|rowspan=3|Can be also changed via ESC "R"
|-
|DS1-2||International characters Bit1
|-
|DS1-3||International characters Bit2
|-
|DS1-4||Page length||11 inch||12 inch||Can be also changed via ESC "C"
|-
|DS1-5||Skip perforation||Disable||Enable||Can be also changed via ESC "N"/ESC "O"
|-
|DS1-6||Alarm beeper||Disable||Enable||Affects chr(07h) and/or Paper-Out alarm (?)
|-
|DS1-7||Default Character Set||Standard/Draft||LQ Letter Quality||Can be also changed via ESC "x"
|-
|DS1-8||SLCT IN signal||Not sent||Automatically sent||?
|-
|DS2-1||Paper out sensor||Enable?||Disable?||Can be also changed via ESC "8"/ESC "9"
|-
|DS2-2||CR Function||CR only (default)||CR & LF||Affects chr(0Dh)
|-
|DS2-3||Zero character||Unslashed||Slashed||Affects chr(30h)
|-
|DS2-4||Reserved|| - || - || -
|-
|DS2-5||Character Set||Epson||IBM#2||...
|-
|DS2-6||Unused|| - || - || -
|-
|DS2-7||Auto loading||Enable||Disable||...
|-
|DS2-8||Reserved|| - || - || -
|-
|colspan=5|'''LQ3500di/LQ5000di Extra RS232 DIP-switches'''
|-
|DS3-1||Baudrate Bit0||colspan=2 rowspan=3|0=9600, 1=4800, 2=2400, 3=1200, 4=600, 5=300, 6=200, 7=150 bps<br>
default = 9600 = all off
|-
|DS3-2||Baudrate Bit1
|-
|DS3-3||Baudrate Bit2
|-
|DS3-4||Parity Even/Odd||Odd||Even
|-
|DS3-5||Parity On/Off||Disable||Enable
|-
|DS3-6||Data Bits||8bit||7bit
|-
|DS3-7||Handshake Bit0||colspan=2 rowspan=2|3=off:off=Parallel/Centronics<br>2=on:off=Serial/XonOff<br>1=off:on=Serial RTS read/busy<br>0=on:on=Serial Etx/Ack
|-
|DS3-8||Handshake Bit1
|-
|}