Analog Joysticks

The CPC+ and GX4000 contain an analog joystick port (additionally to the normal Digital Joystick port).

Technical

The connector is similar as PC/Soundblaster joystick ports, for details on the pin-outs (and differences between CPC and PC joysticks), see:

• Analog Joystick Port Pin-Outs

The buttons are accessed same ways as for Digital Joysticks (ie. as part of the keyboard matrix).

The analog inputs are read from memory mapped ASIC registers:

 6808h  ADC0  Analogue Joystick 1, X-Axis (00h=Left=0 ohm, 3Fh=Right=180K ohm)
 6809h  ADC1  Analogue Joystick 1, Y-Axis (00h=Up  =0 ohm, 3Fh=Down =180K ohm)
 680Ah  ADC2  Analogue Joystick 2, X-Axis (00h=Left=0 ohm, 3Fh=Right=180K ohm)
 680Bh  ADC3  Analogue Joystick 2, Y-Axis (00h=Up  =0 ohm, 3Fh=Down =180K ohm)
 680Ch  ADC4  Unused, wired to +5V (twice the maximum of 2.5V)   (returns 3Fh)
 680Dh  ADC5  Unused, wired to GND (equivalent to 0 ohm)         (returns 00h)
 680Eh  ADC6  Unused, wired to +5V (twice the maximum of 2.5V)   (returns 3Fh)
 680Fh  ADC7  Unused, wired to GND (equivalent to 0 ohm)         (returns 00h)

To read that registers: Unlock the ASIC, and then map its register to memory at 4000h..7FFFh.

Analog CPC+ Joysticks

Currently, the only known CPC+ compatible analogue joysticks is the Sinclar SPJ-1.

• SPJ-1 Sinclar Professional Joystick
• 

  SPJ-1 with Box

• 

  SPJ-1 Booklet

The SPJ-1 (Sinclair Professional Joystick) was produced to accompany Amstrad's unsuccessful Sinclair PC200 (an old PC with 8086 processor). The SPJ-1 was a fully-fledged analogue joystick, with potentiometers used to measure input (rather than switches as in its digital precessors). It was probably a rebadged PC-standard device. The SPJ-1 was, like its host machine, a flop, and today appears to be exceptionally rare.

Analog PC Joysticks

Analog PC Joysticks have a very similar 15pin connector. Theoretically, a few PC joysticks might be CPC+ compatible. However, in practice, this is rather unlikely - the potentiometers must have correct value, the button common pin must be correct, and the joystick may not contain additional electronics like auto-fire circuits, electrolyte capacitors, or digital-switch to analog-signal converters.

• Caution - compared with PCs, the CPC+/GX4000 do output reversed polarity on the joysticks power supply pins, so any special electronics in PC joysticks may get destroyed when connecting them to a CPC Plus/GX4000.

If you want to use a PC joystick: Remove any electronics other than the potentiometers and buttons. Ensure that buttons are wired to correct common pin. And, probably you'd need to replace the potentiometers (if they aren't 180K) - however, this may be the complicated part: potentiometers in analog joysticks aren't necessarily matching standard mechanical dimensions.

CPC+ Software with Analog Joystick Support

• Tennis Cup 2 ( Cartridge ) - allows to use Analog Joystick (as digital joystick replacement in two-player mode, selectable in options menu - the game merely emulates digital inputs, it doesn't actually support analog input)
• RP11 Arnold V diagnostic ROM cartridge - allows to display the eight ADC inputs in numeric form
• FutureOS - homebrew operating system (Plus version)