VDOS
The disc operating system VDOS was developed by the German company Vortex.
It was provided for use with the Vortex Disc Drives from Vortex (F1-D, F1-S, F1-X, M1-D, M1-S or M1-X).
VDOS was supplied on an EPROM, and was released in 3 versions:
- VDOS 1.0
- VDOS 2.0
- VDOS 2.11
Further there were German and English versions of this ROMs.
The VDOS ROM also contained a machine language monitor.
VDOS is the first DOS to support the Vortex format which become a standard format later on.
Contents
Details
- Vortex is a German company, so they added RSX commands in German and English language. VDOS had both |TAPE and |CAS (which resemble equivalent German word Kassette). (Dobbertin's X-DDOS had the same for compatibility).
- |USER/|DRIVE did not exist in V1.0 instead |SELECT is used (which resemble equivalent German word Selektieren). (Dobbertin's X-DDOS also had |SELECT for compatibility).
|SELECT is used to both select user and/or drive. e.g. |SELECT,"3" for user 3, |SELECT,"B" for drive B, |SELECT "4B" for user 4 on drive B. VDOS doesn't have USER or DRIVE commands.
- VDOS supplied both German ROMs (with messages in their native language) and English ROMs where the messages are translated. The RSX commands are identical.
- When using the firmware function CAS CATALOG you give it the address of a buffer to fill with the list of files in the current user and drive (in SOFT968 this is a 2KB buffer but only because AMSDOS is limited to 64 directory entries and each directory is 32 bytes - 64x32 = 2048). For VDOS you should use a 4KB buffer to support 128 directory entries. In addition the format of the data stored in the buffer differs compared to AMSDOS.
AMSDOS uses:
<ff> <8 bytes filename> <3 bytes extension> <2 bytes size in K> with a byte of 00 to indicate the end of the list.
VDOS uses:
<user> <8 bytes filename> <3 bytes extension> <2 bytes size in K> with a byte of FF to indicate the end of the list.
This is important if you use CAS CATALOG and parse the data to fetch the list of files.
- AMSDOS allows you to specify both the user and drive in a filename.
e.g. "3B:TEST.BIN" is valid and will try to find TEST.BIN in user 3 of drive B.
VDOS doesn't allow this. VDOS only allows the drive to be specified.
e.g. "B:TEST.BIN".
Therefore it's recommended to use SELECT to specify the user. A program should also not rely on the memory location of DOS specific data and poke it directly. Therefore it should use KL FIND COMMAND to detect |SELECT and use that if found, otherwise find and use |DRIVE and |USER. This allows maximum compatibility.
- VDOS will autoboot a file called "HELLO.BAS" if it exists on the disc. AMSDOS doesn't have this. This is VDOS's 'Turnkey' system.
Manual
- Vortex Vdos 2.0 Manual (pdf)
(also describes how to upgrade from VDOS 1.0 to 2.0)
Media
Boot-up VDOS message
VDOS external look
Internals photo
Download
Manual (German)
- VDOS 2.0 Manual (German)
Frontpage
Contents
Page 1
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Page 31
Page 32
Page 33
Erata page 1
Erata page 2
Erata page 3
Erata page 4
Erata page 5
