A TV SCART cable allows to connect the CPC/CPCplus to the TV set. This is especially helpful if you couldn't get your hands on a colour monitor or want to use the CPC/CPCplus as a video console in the living room.
Schematics
Amstrad/Schneider CPC (classic)
Colour Picture (RGB)
This schematic requires a TV with RGB input on Scart Connector (back in the 8bit era, many TVs have had only Composite input implemented on Scart connectors - nowadays RGB is also supported by DVD players and 3D gaming consoles, which is possibly increasing the chance to find RGB support on modern TVs).
The 9V and 1.5V batteries are optional. They may be helpful to switch the TV to RGB mode automatically, without needing to activate it via buttons on the remote control. Instead of the batteries, you may also extract the voltages from elsewhere (like the CPC supply), valid are Pin8 = 9.5V - 12V (9V is actually a bit too low), and Pin16 = 1V - 3V.
Black & White Monochrome Picture
This schematic passes Luminance to the TVs Composite Input. It's giving only a monochrome picture, the advantage is that it works on nearly all TVs including such without RGB input.
Doing this would be useful only for using the TV as replacement for the GT64/GT65 monitor.
Bug: The 1.5V battery shown in the mono schematic is nonsense; for composite, Pin16 should be wired to GND, not to 1.5V.
Alternative RGB Wiring
Amstrad CPCplus (In theory also GX4000, but it has its own SCART outlet)
Colour Picture (RGB)
John King's Comments about CPC Plus to Television Scart Lead - 27/7/02
TO TELEVISION WITH AV SWITCHING.
Perhaps I should start by saying that the tasks to be undertaken on this page are not for those of you without electrical and soldering skills, but for the competent, the following circuit will give a quality picture and stereo sound through a television set from an Amstrad CPC6128 Plus, a CPC464 Plus and GX4000. The lead has been tested on a number of different makes of TV (with complete success), within, the age range of 1 to 4 years. I have been unable to find anyone admitting to owning a TV without AV switching so no provision has been made in the offered lead for these old obsolete televisions.
- PARTS AND TOOLS REQUIRED.
- Scart Plug (also known as an Euroconnector or Peritel Plug).
- 8 pin male DIN Plug.
- 6 feet of six core cable.
- 6 feet of twin screened cable.
- 15 watt Soldering Iron.
- Solder.
- Electrical tape (or cable ties).
- MultiMeter.
- Side cutters, Long nosed pliers and a small screw driver (all of which can be found in any DIY tool box).
Just in case it is not obvious, use the six core cable to connect the DIN plug video/RGB connections to the Scart plug and the twin screened cable is for the sound connections to the Scart Plug. Now that the Scart lead has been made up following the above diagram, tape the two leads together (or use cable ties). Now you will need to turn to making a suitable power supply for your CPC Plus/GX4000 machine.
The GX4000 offers a Scart socket for connection to a TV (The Pin connections are listed wrongly in it's manual!). You will need to use the power supply (if not already defective) as issued with the machine, when using a Scart lead.
POWER SUPPLY.
You will need to find a Power Supply Unit giving a 5 volt regulated DC output. The advanced 3 inch disc drive as fitted to the CPC6128+ does not require 12 volts. Both the CPC464Plus and GX4000 will work fine using the same 5 volt power supply. The + voltage should be in the centre of the 2.5mm DC power connecting plug.
An excellent option to use as a Power Supply Unit, is as supplied by Commodore for their various models of computer. Cheap to buy, with a mains on/off switch and colour matched to the CPC+ machines. 5 volts DC is available from all units so far encountered (but do check the base of the unit for specifications) with current ratings at between 2.5 and 4.3 amps.
It is well worth the effort of making up a Scart lead and power supply unit for your CPC Plus/GX4000 machines, as the quality of picture and sound far exceeds that obtained from a Black/White or colour monitor. Games are given a new meaning when played using a 32 inch wide screen Television.
NB Due to the nature of Television design there is a possibility that the lead will not work on every make and model of TV sold thoughout the world.
© J.R.P.King. Updated 27th July 2002.
Black & White Monochrome Picture
Additional Resistors
Info from OCT: "I recall that when Amstrad Action came up with the proposal for a SCART cable back in issue AA41, numerous readers wrote in suggesting that resistors (most commonly: slightly below 330 ohms) should be connected "in series to the colour signals [...] for improving picture quality" (AA45, June 1989, FORUM, p. 23), so they seem to have appeared overblown in comparison to the CTM644s' back in the day."
The goal of that improvement is unknown - it might alter the medium-to-bright ratio, or, it might be simply intended to reduce the overall brightness (such like when the CPC picture appears brighter then normal TV programs). The voltage/brightness output by the CPC is actually higher than normal SCART voltages, however, the voltage drops when the TV applies load to the RGB pins; that load may vary from TV to TV, and so, the resistors may be needed only on some TVs, but not on others.
Videos
A SCART cable howto:
{{#ev:youtube|yNT36Tf6PxU|300}}
See also
- Connector:Monitor - Video output on the CPC