Guide for HxC SD Version

HxC SD Emulator Guide (How to power the HxC Floppy Emulator)

Powering the board you need a 5V from a normal pc power supply or similar. As you only need the 5V (usually red wire) and not the 12V (Yellow) perhaps it would be best use a extender (V-split) cable and cut the 12V cable so you dont fry the board. Better read the manual carefully, especially if you want to use the board internally where the Amstrad power is usually just opposite the pc one.

Note: people who got a board from Lotharek may already have the latest version firmware v1.0.1.1 on it so you wont need to upgrade. When you turn on your board it will show your version in the display.
First you should upgrade your boards firmware. The firmware file (.UPD) needs to be the first file on the SD card. Also the file needs to be in one (cant be fragmented all over the SD card). So first you should format your SD card to FAT32 (or reformat just to make sure). Then copy over the .UPD (like HXCFE_V0_2_2_0.UPD) file to the root of the SD card.

Once you have the prepared SD card in the emulator. Press down the "move left" and "move right" keys together and then power the board. Should take 1-2 seconds tops to flash the board.

(to format a drive go to Control Panel then Administration and choose the right click the drive to get the format option).

Better get the lastest firmware here:
http://hxc2001.free.fr/floppy_drive_emulator/index.html#SDCARDFloppyemulator

Download the latest emulator software here:
http://hxc2001.free.fr/floppy_drive_emulator/index.html#SoftwareFloppyemulator

Open the Software and choose "Drive" then "SD HxCFE settings file". Click on SAVE to make the HXCSDFE.CFG file (choose default options) and save it on your SD CARDS root.

DSKs need to be converted to the HFE file format before being put on the SD card. "LOAD" the DSK in the Software and "Export" it to HFE file. Batch converison is also possible with the "Convert" button.
If you need to get a HFE file converted back to DSK then "load" the HFE and "Export" it to DSK file.

Set the right jumpers on the board (Default on my was "primary A:"). But as most people will probably use the drive as secondary B drive. Secondary drive setting is shown here:

1. First it will ask if its the A Drive (click middel button .. aka accept). Even if you use the drive as 2 drive you need to choose A Drive option here.
2. scrool between HFE image files using the left/right buttons.
3. Press middel button to select (insert disc). To choose another image later make sure to eject the current disc first (again middel button).

Just like with a real floppy disc its possible to damage the disc if it still inserted when powering on and off. So before turning off you should "eject" the disc by pressing the middel key on the emulator board, just to be safe. Similar is when you turn on your system and the floppy is still "inserted", its best to do a quick eject and then insert the image again to avoid errors on the disc.

With this utility you can now choose which disk image to use from the Amstrad itself! When this utility is used the buttons on the interface work as follows:

Right button : Next Slot
Center button : Slot 0 - SDCard HxC Floppy Emulator Manager floppy image.
Left button  : Previous Slot

To run the floppy manager software type : run"hxc

When the manager is run, the user is presented with an interface through which he can navigate the SD card's filesystem and insert disk images in different slots. Then he can press F9 and the system is rebooted with the selected image appearing in the drive. This is a much faster and user-friendlier solution to the hard buttons.

The Good:
- Really well made board (smaller than the USB one) and was well packed.
- Nice led screen (cool).
- It works quite well and is more mobile than the USB version.
- Reads and writes all discs so far.
- You can turn off the track/read noise.
- The software supports DSK export, so you can also use the setup to transfer software back from CPC to Pc.

The Bad:
- a 200kb DSK converts to 1mb HFE file. Good thing that SD cards are large and cheap today.
- the white power plug on the board (Lotharek version) dosnt have a "hole" so a normal power cable wont fit unless you file off the little white "tooth".
- I realise again that most of the amstrad software isnt compatible to be loaded from a second B drive (not the boards fault of cause). Of cause you can always copy the disk to the primary drive and run it from there. A hardware solution is make a ABBA_switch.

HxC official homepage (has manual, firmware and software):
http://hxc2001.free.fr/floppy_drive_emulator

Lotharek site (sells HxC on ebay):
http://atari.plof.pl/