Amstrad/Schneider Printer Models

• Amstrad/Schneider Printer Models
• Amstrad/Schneider Printer Technical Specifications
• Amstrad/Schneider Printer Control Codes
• Amstrad/Schneider Printer Support for 7bit Printer Ports
• Amstrad/Schneider Printer Character Sets
• Amstrad/Schneider Printer Buttons and DIP Switches
• Amstrad/Schneider Printer Resources (User and Service Manuals, Datasheets, ROM-images)

CPC Series

• Amstrad DMP-1 (Seikosha GP500) more info
• Early unihammer printer (with 7-dot columns)
• Very slow, with rather crude character set (without underlengths and without NLQ)

• Schneider NLQ401 (GLP500) more info
• This is Schneider's counterpart to the Amstrad DMP1.
• The NLQ401 is a 9pin printer with NLQ und underlength support (thus much better than the DMP1). The NLQ character set is defined in very high horizontal resolution (even better than the NLQ sets in later DMP2000..DMP3000 models).
• Unlike DMP1 and DMP2000..3000, the NLQ401 doesn't include a SRAM chip (so data can be buffered only in a portion of the CPU's on-chip 256-byte RAM).

• Amstrad/Schneider DMP2000 more info
• Epson FX-80 compatible 9-pin printer (with additional NLQ support, which wasn't supported on the original FX-80)
• Same hardware as DMP3000, but in CPC-style black case (see DMP3000 section for some extra differences)

• Amstrad/Schneider DMP2160 more info
• Fast version of DMP2000 (prints 160 CPS, instead of 105 CPS)

PC Series (gray)

• Amstrad/Schneider DMP3000 more info
• Same hardware as DMP2000, with following differences:
  • PC-style gray case (instead of the darker CPC coloured case)
  • More RAM (8Kbyte; instead of 2Kbyte)
  • More EPROM (8K+16K, or optionally 32K; instead of 16Kbyte)
  • Additional IBM character set (instead plain 7bit Epson/ASCII charset)
  • AutoLF signal supported (enabled via J4 jumper; instead of GNDing the AutoLF input)
  • User manual addressed to PC users (instead of CPC/MSX/BBC/C64 users)
  • and, maybe... additional italics support (DMP2000 doesn't explicitly mention italics support; though probably both DMP2000+3000 do support them)?

• Amstrad/Schneider DMP3160 more info
• Fast version of DMP3000 (prints 160 CPS, instead of 105 CPS)

• DMP3250di more info
• Dual-interface version of DMP3160 (with centronics and rs232 ports)
• Like the DMP3160, it prints only 160 CPS (not 250 CPS)
• Slightly redesigned case (bigger transparent plastic lid, and metal stands moved from left/right to front/back side)

• DMP4000 more info
• Extra big wide printer (paper width 16 inch)
• Said to be compatible with Epson FX-100 (the wide version of the Epson FX-80)

• LQ3500 and LQ3500di more info
• LQ3500di version with dual interface (centronics and rs232)
• Letter Quality 24pin Dot Matrix Printer

• LQ5000di more info
• Letter Quality 24pin Dot Matrix Printer, wide carriage (16 inch paper)
• With dual interface (centronics and rs232)

• LD6000 more info
• Laser Printer (from Amstrad GmbH, for german market only)
• This is a rebadged Sharp printer that emulates an HP Laserjet II

PCW Series (non-centronics)

PCWs were sold bundled with special printers, some with Dot Matrix printers, others with daisy wheel printers. The PCW printers aren't centronics compatible (most of the printer electronics is contained on the PCW computer mainboard, whilst the PCW printer contains only mechanics and low-level electronics).

• PCW8256 printer (see also)
• The printer that was bundled with the PCW8256