C4CPC

C4CPC is a cartridge replacement for the Amstrad Plus range and the GX4000.

Using a micro-SD card storing cartridge images it also allows direct loading of the cartridge from a PC (Windows/Linux/OSX) through USB.

Features

Direct access to 16 cartridges selected by dip switches. Cartridge can be up to 512kB
Access to unlimited number of cartridge images using the provided selector cartridge
Direct cartridge loading from host computer using USB
Cartridge file can be in standard .cpr format or raw binary .bin
Integrated ACID simulator

Using C4CPC on a GX4000 with the original Amstrad power supply may cause damage to the GX4000 please read this forum thread

User guide

Quick start

Power off you Amstrad Plus / GX4000
Insert the C4Cpc cart with a prepared SD in the cartridge slot, DIP switch facing up on 464/6128, DIP on joystick port side on GX4000

In GX4000
In 6128/464 plus
Dip Switch to Slot table

Select your favourite cart slot on the DIP switch
Power on ...
et voilà !

Cartridge selector

CprSelect is a special cartridge that allows browsing the SD cart for cartridges to load. The main area displays the current folder contents. Browsing is done using either one of the joysticks or the keyboard.

Keyboard controls : cursors for browsing, space/enter/copy to select and esc to return to parent folder
Joystick controls : left/right/up/down for browsing, fire 1 to select, fire 2 to return to parent folder

Left/Right jump from page to page if the folder cannot be displayed in one screen.

SD card preparation

The C4CPC is delivered with a prepared microSD card which contains the Basic Cartridge in slot 0 and the cartridge selector in slot 15. Using your computer, cartridge images can be added to any slots or cartridge selector by writing to the SD card.

The SD must contains at least the following folder tree

_C4CPC : This is the main folder that contains the dip switch selectable folder.
_C4CPC/0 to _C4CPC/F folders, which should contain only one valid CPR/BIN file. The cartridge emulator will first look for a CPR then a BIN file and load it to the cartridge.

SD original content can be found in File:C4CpcSdContent base.zip

How it works

At power up, CPC/USB whichever is the first, the uC will check for a valid .CPR/.BIN file to load in the DIP switch selected slot.

If the file is smaller than 160KB, it will be loaded directly
If no file is available or the file is bigger than 160KB, a bootloader is 1st loaded. The bootloader will then load the file if any.

C4CPC is powered either by the CPC or/and the USB port. That means that power cycling the CPC will NOT initiate a new cart loading if the cart is also powered by USB.

Cart loading from USB

A connected cart should appear as a serial port (COMx on windows, /dev/ttyACMx on linux, /dev/tty.modemxxxx on OSX). Windows require a .inf file to install the proper drivers. Loading is done using a python3 script which has the following syntax :

C4CpcCom.py -p port cart.cpr

where port is the serial port assigned to the cart.

Example for linux: sudo python3 C4CpcCom.py -p /dev/ttyACM0 cart.cpr

Latest version available in File:C4CpcCom.zip will only work with FW V1.00.01 and upward

Firmware upgrade

C4CPC microcontroller firmware is user upgradable through the USB port and requires the following tools and drivers :

dfu-programmer for updating the code
driver : provided with dfu-programmer windows version, native support on recent linux and OSx

A dedicated forum thread exists for new firmware announcement support and discussion.

Update requirement

Update procedure requires the dfu-programmer software:

Executable version is provided for windows users.
Linux users should find it in they distribution repository or build it from source. Older versions (before 0.7) of dfu-programmer have different commands so they will fail to run the UpdateCartEmu.sh script correctly. It is highly recommended you download the source and build it.
OSX users will have to build it from provided source and script in dfu-programmer_install_OSX. Check the included readme.txt for detail.

Upgrade procedure

Start C4CPC in usb update mode

put dip switch 4 ON (other three switches to OFF)
connect the card in one USB port
press and release the C4CPC reset switch

Install DFU driver (Windows only)

With the latest C4CPC zip you may find that running the program reports 'libusb' not found or it doesn't find the device. Please follow the 'NEW' section below for success.

OLD *After the reset, windows will look for the device drivers. These are located in the windows\dfu-prog-usb-1.2.2 folder

NEW * Download the latest 'dfu-programmer'

   a) go to https://github.com/dfu-programmer/dfu-programmer/releases/tag/v1.1.0
   b) Download 'dfu-programmer-x64-1.1.0.zip'
   c) Extract the contents
   d) Copy 'dfu-programmer.exe' and 'libusb-1.0.dll' from the extracted contents into the C4CPC 'windows' directory replacing and replace the exe already there.

   * Run 'zadig' (https://zadig.akeo.ie/)
   a) Options->List all devices
   b) Choose ATm32U4DFU
   c) Install the 'WinUSB' driver.

You now just need to run the update script :

Linux/OSx, you need to have root/admin right

sudo UpdateCartEmu.sh

Windows, from the update package windows folder

UpdateCartEmu.bat

A successful update looks like this :

Manufacturer Code: 0x58 (88)
--- Erase ---
Erasing flash...  Success
Checking memory from 0x0 to 0x6FFF...  Empty.
--- Flash ---
Checking memory from 0x0 to 0x4DFF...  Empty.
0%                            100%  Programming 0x4E00 bytes...
[>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>]  Success
0%                            100%  Reading 0x7000 bytes...
[>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>]  Success
Validating...  Success
0x4E00 bytes written into 0x7000 bytes memory (69.64%).
--- EEProm ---
0%                            100%  Programming 0x380 bytes...
[>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>]  Success
0%                            100%  Reading 0x400 bytes...
[>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>]  Success
Validating...  Success
0x380 bytes written into 0x400 bytes memory (87.50%).