Vortex Disc Drives

A series of external 3.5" and 5.25" floppy disc drives from Vortex providing up to 720K capacity (704K available). The Vortex drives were most popular in Germany. For more information regarding VDOS and the Vortex Disk Format, see the dedicated VDOS Wiki page.

S- and D-Drives (720K)

These are the first generation of 720K floppy disc drives from Vortex. They came in variants having either a single drive ("S" variant) or two drives ("D" variant). The "S" variant (as well as the less expensive "Z" variant) was delivered with the same double-height casing as the "D" variant, so that a second drive could be retrofitted. The 5,25" drives used were BASF 6138 type drives (double-sided, double density, 80 tracks per side, 96 tpi).

Variants

F1-S - single 5.25" drive
F1-D - double 5.25" drive
M1-S - single 3.5" drive
M1-D - double 3.5" drive

F1-D
F1-D front view
F1-D backside
F1-S/D manual
F1-S/D system disk

F1-D interface (CPC 664)
F1-D interface board (CPC 664)
F1-D interface board (CPC 664)

F1-D interface board (CPC 6128)

A1-S Upgrade Kit

Vortex offered an upgrade kit consisting of a single bare drive and an installation manual, allowing to upgrade a single F1/M1-S drive to a dual F1/M1-D drive. To do this, one simply had to install the additional drive in the free slot of the drive case.

FDA-1 3" Drive Adapter

This adapter makes it possible to connect an external FD-1 3" drive on Vortex F1/M1 setups on the CPC 464. Since only two drives can be used at the same time, the external 3" drive first had to be selected manually with RSX commands.

RSX	Description
\|S,1	Use 3" drive as drive A, upper Vortex drive is disabled
\|S,2	Use 3" drive as drive B, lower Vortex drive is disabled
\|S,0	Disable the 3" drive (default)

FDA-1 Adapter
Inside the adapter box
Inside the adapter box (closeup)

FDC I/O Ports

All types of floppy disk controllers for the F1-S/D and M1-S/D series are based on the NEC 765 chip. The manual states that on "controllers having an integrated ROM module/eprommer" (probably the later 6128 interfaces?), the port addresses can be freely configured using a decoder ROM.

CPC 464:

Address	Description
0xFB7E	uPD control
0xFB7F	uPD data
0xFA7E	motor on/off

CPC 664/6128:

Address	Description
0xFBF6	uPD control
0xFBF7	uPD data
0xFA7E	motor on/off

Downloads

Benutzerhandbuch für die Vortex Floppy Disk Station F1 für den Schneider CPC 464 (Vortex F1 user manual)
Benutzerhandbuch für das Diskettenbetriebssystem VDOS 2.0 (VDOS 2.0 user manual)
Benutzerhandbuch für den FDA-1 3"-Adapter (3" adapter user manual)
Vortex F1-S/D Systemdiskette für CPC 664/6128 (system disk, 720k image)
VDOS 1.0 ROM
VDOS 2.0 ROM
BASF 6138 Datasheet (F1-S/D/Z Floppy Disk Drive)

Z-Drives (180K/side)

These are less expensive drives and were meant to be directly connected as B drive to a CPC 464 with DDI-1 or a CPC 664/6128. Since these drives ship neither with an own controller nor a VDOS ROM, they do rely fully on AMSDOS and thus only 40 tracks on one side can be accessed, resulting in the same capacity (180K/side) as the 3" drives. Technically, the Z-drives are actually only S-drives without Vortex controller and CP/M licence.

The 5.25" drive used in the F1-Z is a later revision of the BASF 6138 (81757-001), which offers more configuration options using jumpers. The drive was shipped with a setting of 40 tracks, and thus the cheaper 48 tpi DS-DD disks could be used.

Variants

F1-Z - single 5.25" drive
M1-Z - single 3.5" drive

A1-Z Upgrade Kit

Vortex offered an upgrade kit consisting of a controller, manual, CP/M license and an utility disk which upgraded a Z-Drive to a S-Drive.

X-Drives (720K)

These are the latest drives from Vortex for use with a CPC 464 with DDI-1 or a CPC 664/6128 (ie. on systems that already have a floppy disc controller); no additional controller was required anymore. Instead, a ROM module was supplied together with the drive, which provided VDOS 2.0-X. Only single-drive variants were available. The |S command (for accessing a third drive) is no longer used, the new |X command allows to swap drive A and B (same as X-DDOS from Dobbertin). The X-Drives are equipped with BASF 6139 drives, which are compatible with the BASF 6138 drives of the previous 5,25" models but have a slightly more compact design.

Variants

F1-X - single 5.25" drive
F1-XRS - single 5.25" drive with RS232-C interface
M1-X - single 3.5" drive
M1-XRS - single 3.5" drive with RS232-C interface

F1-X
F1-X backside, showing IDC connector (CPC 464)
F1-X backside, showing edge connector (CPC 664)
F1-X inside view, showing a BASF 6139 drive
F1-X/M1-X manual and system utilities disk

M1-X
M1-X backside
M1-X backside, showing IDC connector (CPC 464)
M1-X underside
M1-X inside view, showing the drive and power
M1-X inside view, close-up of the drive from above
M1-X inside view, close-up from the backside

X(RS)-Modul

The X-drives for the CPC 664/6128 are connected directly to the floppy port. In order to provide VDOS, the "X-Modul" (sometimes also called "VDOS module") must be connected additionally to the expansion port. This contains a ROM board that provides a VDOS 2.0-X ROM and was also available with an additional RS232-C interface (in this case called "XRS-Modul"). The ROM board supplied for the CPC 464 came together with a chunky housing in which both the "X(RS)-Modul" and the DDI-1 controller were installed.