Vortex Disc Drives

A series of external 3.5" and 5.25" floppy disc drives from Vortex providing up to 720K capacity (704K available). The Vortex drives were most popular in Germany. For more information regarding VDOS and the Vortex Disk Format, see the dedicated VDOS Wiki page.

S- and D-Drives (720K)

These are the first generation of 720K floppy disc drives from Vortex. They came in variants having either a single drive ("S" variant) or two drives ("D" variant). The "S" variant (as well as the "Z" variant) was delivered with the same double-height casing as the "D" variant, so that a second drive could be retrofitted. The 5,25" drives used were BASF 6138 type drives (double-sided, double density, 80 tracks per side, 96 tpi).

Variants

F1 - S Single 5.25" drive with power supply and custom NEC 765 based controller providing VDOS
F1 - D Double 5.25" drive with power supply and custom NEC 765 based controller providing VDOS
M1 - S Single 3.5" drive with power supply and custom NEC 765 based controller providing VDOS
M1 - D Double 3.5" drive with power supply and custom NEC 765 based controller providing VDOS

F1-D
F1-D front view
F1-D backside
F1-S/D manual
F1-S/D system disk

F1-D interface (CPC 664)
F1-D interface board (CPC 664)
F1-D interface board (CPC 664)

F1-D interface board (CPC 6128)

A1-S Upgrade Kit

Vortex offered an upgrade kit consisting of a bare 5,25" drive (BASF 6138) and an installation manual, allowing to upgrade a single F1-S drive to a dual F1-D drive. To do this, one simply had to install the additional drive in the free slot of the drive case.

FDA-1 3" Drive Adapter

This adapter allows to use an external Amstrad FD-1 3" drive on Vortex F1/M1 setups connected to a CPC 464. Since only two drives can be used simultaneously, the 3" drive had to be manually selected first using RSX commands.

3" Adapter zur VORTEX-Diskettenstation (manual)

RSX	Description
\|S,1	Use 3" drive as drive A, upper Vortex drive is disabled
\|S,2	Use 3" drive as drive B, lower Vortex drive is disabled
\|S,0	Disable the 3" drive (default)

Adapter to connect an additional 3" disc drive in between a CPC 464 and a F1/M1
Inside the adapter box
Inside the adapter box (closeup)

FDC I/O Ports

All types of floppy disk controllers for the F1-S/D and M1-S/D series are based on the NEC 765 chip. The manual states that on "controllers having an integrated ROM module/eprommer" (probably the later 6128 interfaces?), the port addresses can be freely configured using a decoder ROM.

CPC 464:

Address	Description
0xFB7E	uPD control
0xFB7F	uPD data
0xFA7E	motor on/off

CPC 664/6128:

Address	Description
0xFBF6	uPD control
0xFBF7	uPD data
0xFA7E	motor on/off

Downloads

Benutzerhandbuch für die Vortex Floppy Disk Station F1 für den Schneider CPC 464 (Vortex F1 user manual)
Benutzerhandbuch für das Diskettenbetriebssystem VDOS 2.0 (VDOS 2.0 user manual)
Vortex F1-S/D Systemdiskette für CPC 664/6128 (system disk for F1-S/D drives, 720k image)
VDOS 1.0 ROM
VDOS 2.0 ROM
BASF 6138 Datasheet (F1-S/D/Z Floppy Disk Drive)

Z-Drives (180K/side)

These are less expensive drives and were meant to be directly connected as B drive to a CPC 464 with DDI-1 or a CPC 664/6128. Since these drives ship neither with an own controller nor a VDOS ROM, they do rely fully on AMSDOS and thus only 40 tracks can be accessed. The Z-drives were basically S-drives without a Vortex controller and CP/M license.

Variants

F1 - Z Single 5.25" drive with power supply with ribbon cable (does not come with interface containing FDC or VDOS)
M1 - Z Single 3.5" drive with power supply with ribbon cable (does not come with interface containing FDC or VDOS)

A1-Z Upgrade Kit

Vortex offered an upgrade kit consisting of a controller, manual, CP/M license and utility disk which upgraded a Z-Drive to a S-Drive.

X-Drives (720K)

These are the latest drives from Vortex for use with a CPC 464 with DDI-1 or a CPC 664/6128 (ie. on systems that already have a floppy disc controller); no additional controller was required anymore. Instead, a ROM module was supplied together with the drive, which provided VDOS 2.0-X. Only single-drive variants were available. The |S command (for accessing a third drive) is no longer used, the new |X command allows to swap drive A and B (same as X-DDOS from Dobbertin). The F1-X(RS) models are equipped with BASF 6139 drives, which are compatible with the BASF 6138 drives of the previous 5,25" models but have a slightly more compact design.

Vortex X-Laufwerke (manual)
Vortex Systemdiskette für X-Laufwerke (system disk, 720kB image)
Manual de las Unidades Vortex (manual)
NEC FD1035 Datasheet (M1-X Floppy Disk Drive)

Variants

F1 - X Single 80 track, Double Sided, 5.25" drive with power supply
M1 - X Single 80 Track, Double Sided, 3.5" drive with power supply
F1 - XRS same as F1-X, upgraded with RS232-C interface
M1 - XRS same as M1-X, upgraded with RS232-C interface

F1-X
F1-X backside, showing IDC connector (CPC 464)
F1-X backside, showing edge connector (CPC 664)
F1-X inside view, showing a BASF 6139 drive
F1-X/M1-X manual and system utilities disk

M1-X
M1-X backside
M1-X backside, showing IDC connector (CPC 464)
M1-X underside
M1-X inside view, showing the drive and power
M1-X inside view, close-up of the drive from above
M1-X inside view, close-up from the backside

X(RS)-Modul

The X-drives for the CPC 664/6128 are connected directly to the floppy port. In order to provide VDOS, the "X-Modul" (sometimes also called "VDOS module") must be connected additionally to the expansion port. This contains a ROM board that provides a VDOS 2.0-X ROM and was also available with an additional RS232-C interface (in this case called "XRS-Modul"). The board supplied for the CPC 464 version came in a chunky housing in which both the "X(RS)-Modul" and the DDI-1 controller were installed.