765 FDC

µPD765 - Floppy Disc Controller (used in DDI-1 and CPC 664/6128).

The ports used by Amstrad and compatible interfaces use:

• Port &FA7E - Floppy Motor On/Off Flipflop
• Port &FB7E - FDC 765 Main Status Register (read only)
• Port &FB7F - FDC 765 Data Register (read/write)

The Vortex disc interface uses other ports. See its dedicated wiki page.

IC Models used in CPC

More than one manufacturer made 765 compatible ICs. These are the ones known to be used in the CPC by looking at pictures of CPC mainboards.

All should operate almost identically.

• Zilog Z0765A08PSC
• NEC D765AC-2
• NEC D765AC
• UMC UM8272A

The following data seperators are used:

• FDC9216
• SED9420C

The CPC464, CPC472, 464 Plus and GX4000 are not equipped with a FDC chip.

Accessing the FDC 765

The Main Status Register (Port &FB7E) signalizes when the FDC is ready to send/receive the next byte through the Data Register.

The Data Register (Port &FB7F) is used to write Commands and Parameters, to read/write data bytes, and to receive result bytes. These three operations are called Command-, Execution-, and Result-Phase.

Command Phase

A command consists of a command byte (eventually including the MT, MF, SK bits), and up to 8 parameter bytes.

Execution Phase

During this phase, the actual data is transferred (if any). Usually that are the data bytes for the read/written sector(s), except for the Format Track Command, in that case 4 bytes for each sector are transferred.

During data transfers between the FDC and the processor, the FDC must be serviced every 26µs (for MFM mode with CPC timings) or the FDC terminates the FDC command.

Result Phase

Returns up to 7 result bytes (depending on the command) that are containing status information. The Recalibrate and Seek Track commands do not return result bytes directly, instead the program must wait until the Main Status Register signalizes that the command has been completed, and then it must (!) send a Sense Interrupt State command to 'terminate' the Seek/Recalibrate command.

During the result phase, all the result bytes must be read. The FDC will not accept a new command until all the result bytes are read.

FDC Command Table (15 commands)

Read Data (06h)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	MT	MF	SK	0	0	1	1	0
command byte 1	x					HD	US
command byte 2	C: cylinder number
command byte 3	H: head number
command byte 4	R: sector number
command byte 5	N: bytes per sector
command byte 6	EOT: end of track (ie. last sector in track)
command byte 7	GPL: gap 3 length
command byte 8	DTL: data length (if command byte 5==0)
Execution	Data-transfer from the FDD
result byte 0	ST0: status register 0
result byte 1	ST1: status register 1
result byte 2	ST2: status register 2
result byte 3	C: cylinder number
result byte 4	H: head number
result byte 5	R: sector number
result byte 6	N: bytes per sector

Read Deleted Data (0Ch)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	MT	MF	SK	0	1	1	0	0
command byte 1	x					HD	US
command byte 2	C: cylinder number
command byte 3	H: head number
command byte 4	R: sector number
command byte 5	N: bytes per sector
command byte 6	EOT: end of track (ie. last sector in track)
command byte 7	GPL: gap 3 length
command byte 8	DTL: data length (if command byte 5==0)
Execution	Data-transfer from the FDD
result byte 0	ST0: status register 0
result byte 1	ST1: status register 1
result byte 2	ST2: status register 2
result byte 3	C: cylinder number
result byte 4	H: head number
result byte 5	R: sector number
result byte 6	N: bytes per sector

Write Data (05h)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	MT	MF	x	0	0	1	0	1
command byte 1	x					HD	US
command byte 2	C: cylinder number
command byte 3	H: head number
command byte 4	R: sector number
command byte 5	N: bytes per sector
command byte 6	EOT: end of track (ie. last sector in track)
command byte 7	GPL: gap 3 length
command byte 8	DTL: data length (if command byte 5==0)
Execution	Data-transfer to the FDD
result byte 0	ST0: status register 0
result byte 1	ST1: status register 1
result byte 2	ST2: status register 2
result byte 3	C: cylinder number
result byte 4	H: head number
result byte 5	R: sector number
result byte 6	N: bytes per sector

Write Deleted Data (09h)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	MT	MF	x	0	1	0	0	1
command byte 1	x					HD	US
command byte 2	C: cylinder number
command byte 3	H: head number
command byte 4	R: sector number
command byte 5	N: bytes per sector
command byte 6	EOT: end of track (ie. last sector in track)
command byte 7	GPL: gap 3 length
command byte 8	DTL: data length (if command byte 5==0)
Execution	Data-transfer to the FDD
result byte 0	ST0: status register 0
result byte 1	ST1: status register 1
result byte 2	ST2: status register 2
result byte 3	C: cylinder number
result byte 4	H: head number
result byte 5	R: sector number
result byte 6	N: bytes per sector

Read Track (02h)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	x	MF	SK	0	0	0	1	0
command byte 1	x					HD	US
command byte 2	C: cylinder number
command byte 3	H: head number
command byte 4	R: sector number
command byte 5	N: bytes per sector
command byte 6	EOT: end of track (ie. last sector in track)
command byte 7	GPL: gap 3 length
command byte 8	DTL: data length (if command byte 5==0)
Execution	FDC reads all data fields from index hole to EOT
result byte 0	ST0: status register 0
result byte 1	ST1: status register 1
result byte 2	ST2: status register 2
result byte 3	C: cylinder number
result byte 4	H: head number
result byte 5	R: sector number
result byte 6	N: bytes per sector

Read ID (0Ah)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	x	MF	x	0	1	0	1	0
command byte 1	x					HD	US
Execution	The first correct ID information on the cylinder is stored in data register
result byte 0	ST0: status register 0
result byte 1	ST1: status register 1
result byte 2	ST2: status register 2
result byte 3	C: cylinder number
result byte 4	H: head number
result byte 5	R: sector number
result byte 6	N: bytes per sector

Format Track (0Dh)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	x	MF	x	0	1	1	0	1
command byte 1	x					HD	US
command byte 2	N: bytes per sector
command byte 3	SC: sectors per track
command byte 4	GPL: gap 3 length
command byte 5	D: filler pattern to write in each byte
Execution	FDC formats an entire track
result byte 0	ST0: status register 0
result byte 1	ST1: status register 1
result byte 2	ST2: status register 2
result byte 3	C: cylinder number
result byte 4	H: head number
result byte 5	R: sector number
result byte 6	N: bytes per sector

Scan Equal (11h)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	MT	MF	SK	1	0	0	0	1
command byte 1	x					HD	US
command byte 2	C: cylinder number
command byte 3	H: head number
command byte 4	R: sector number
command byte 5	N: bytes per sector
command byte 6	EOT: end of track (ie. last sector in track)
command byte 7	GPL: gap 3 length
command byte 8	STP: scan test (1=scan contiguous, 2=scan alternate)
Execution	Data compared between the FDD and main-system
result byte 0	ST0: status register 0
result byte 1	ST1: status register 1
result byte 2	ST2: status register 2
result byte 3	C: cylinder number
result byte 4	H: head number
result byte 5	R: sector number
result byte 6	N: bytes per sector

Scan Low or Equal (19h)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	MT	MF	SK	1	1	0	0	1
command byte 1	x					HD	US
command byte 2	C: cylinder number
command byte 3	H: head number
command byte 4	R: sector number
command byte 5	N: bytes per sector
command byte 6	EOT: end of track (ie. last sector in track)
command byte 7	GPL: gap 3 length
command byte 8	STP: scan test (1=scan contiguous, 2=scan alternate)
Execution	Data compared between the FDD and main-system
result byte 0	ST0: status register 0
result byte 1	ST1: status register 1
result byte 2	ST2: status register 2
result byte 3	C: cylinder number
result byte 4	H: head number
result byte 5	R: sector number
result byte 6	N: bytes per sector

Scan High or Equal (1Dh)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	MT	MF	SK	1	1	1	0	1
command byte 1	x					HD	US
command byte 2	C: cylinder number
command byte 3	H: head number
command byte 4	R: sector number
command byte 5	N: bytes per sector
command byte 6	EOT: end of track (ie. last sector in track)
command byte 7	GPL: gap 3 length
command byte 8	STP: scan test (1=scan contiguous, 2=scan alternate)
Execution	Data compared between the FDD and main-system
result byte 0	ST0: status register 0
result byte 1	ST1: status register 1
result byte 2	ST2: status register 2
result byte 3	C: cylinder number
result byte 4	H: head number
result byte 5	R: sector number
result byte 6	N: bytes per sector

Recalibrate (07h)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	x			0	0	1	1	1
command byte 1	x						US
Execution	Head retracted to track 0

Seek (0Fh)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	x			0	1	1	1	1
command byte 1	x					HD	US
command byte 2	NCN: new cylinder number
Execution	Head is positioned over proper cylinder

Sense Interrupt Status (08h)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	x			0	1	0	0	0
result byte 0	ST0: status register 0
result byte 1	PCN: present cylinder number

Sense Drive Status (04h)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	x			0	0	1	0	0
command byte 1	x					HD	US
result byte 0	ST3: status register 3

Specify (03h)

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	x			0	0	0	1	1
command byte 1	SRT				HUT
command byte 2	HLT							ND

Invalid

	D7	D6	D5	D4	D3	D2	D1	D0
command byte 0	x			Invalid Codes
result byte 0	ST0: status register 0

Abbreviations used:

• N = 2^(n+7) bytes. For example, N=2 means 512 bytes
• MT = Multi-track (continue multi-sector function on other head)
• MF = MFM mode (1 = Double Density)
• SK = Skip deleted-data address mark (set if sectors with deleted DAM shall be skipped)
• HD = Head number select
• US = Unit select (drive select)

• HLT = Head Load Time: 2 to 254ms in 2ms increments
• HUT = Head Unload Time: 16 to 240ms in 16ms increments
• SRT = Step Rate Time: 1 to 16ms in 1ms increments (F = 1ms, E = 2ms, etc.)
• ND = Non-DMA mode

Notes:

• Specify: All timings will be doubled on CPC because the FDC runs at 4MHz instead of 8MHz for the datasheet
• Format Track: The processor must supply C, H, R, N to the FDC for each sector during execution phase
• Recalibrate: Walks up to 77 tracks, 80tr-drives may need a second recalibrate if failed
• Seek / Recalibrate: All read/write commands will be disabled until successful sense interrupt

FDC Status Registers

The Main Status register can always be read through Port &FB7E. The other four Status Registers cannot be read directly, instead they are returned through the data register as result bytes in response to specific commands.

Main Status Register (Port &FB7E):

 b0..3  DB   FDD0..3 Busy (seek/recalib active, until succesful sense intstat)
 b4     CB   FDC Busy (still in command-, execution- or result-phase)
 b5     EXM  Execution Mode (still in execution-phase, non_DMA_only)
 b6     DIO  Data Input/Output (0=CPU->FDC, 1=FDC->CPU) (see b7)
 b7     RQM  Request For Master (1=ready for next byte) (see b6 for direction)

Status Register 0:

 b0,1   US   Unit Select (driveno during interrupt)
 b2     HD   Head Address (head during interrupt)
 b3     NR   Not Ready (drive not ready or non-existing 2nd head selected)
 b4     EC   Equipment Check (drive failure or recalibrate failed (retry))
 b5     SE   Seek End (Set if seek-command completed)
 b6,7   IC   Interrupt Code (0=OK, 1=aborted:readfail/OK if EN, 2=unknown cmd
             or senseint with no int occured, 3=aborted:disc removed etc.)

Status Register 1:

 b0     MA   Missing Address Mark (Sector_ID or DAM not found)
 b1     NW   Not Writeable (tried to write/format disc with wprot_tab=on)
 b2     ND   No Data (Sector_ID not found, CRC fail in ID_field)
 b3,6   0    Not used
 b4     OR   Over Run (CPU too slow in execution-phase (ca. 26us/Byte))
 b5     DE   Data Error (CRC-fail in ID- or Data-Field)
 b7     EN   End of Track (set past most read/write commands) (see IC)

Status Register 2:

 b0     MD   Missing Address Mark in Data Field (DAM not found)
 b1     BC   Bad Cylinder (read/programmed track-ID different and read-ID = FF)
 b2     SN   Scan Not Satisfied (no fitting sector found)
 b3     SH   Scan Equal Hit (equal)
 b4     WC   Wrong Cylinder (read/programmed track-ID different) (see b1)
 b5     DD   Data Error in Data Field (CRC-fail in data-field)
 b6     CM   Control Mark (read/scan command found sector with deleted DAM)
 b7     0    Not Used

Status Register 3:

 b0,1   US   Unit Select (pin 28,29 of FDC)
 b2     HD   Head Address (pin 27 of FDC)
 b3     TS   Two Side (0=yes, 1=no (!))
 b4     T0   Track 0 (on track 0 we are)
 b5     RY   Ready (drive ready signal)
 b6     WP   Write Protected (write protected)
 b7     FT   Fault (if supported: 1=Drive failure)

C, H, R, N values at result phase

If the processor terminates a read (or write) operation in the FDC, then the ID information in the Result phase is dependent upon the state of the MT bit and EOT byte:

MT	HD	Final Sector Transferred to Processor	ID Information at Result Phase
			C	H	R	N
0	0	Less than EOT	-	-	R + 1	-
0	0	Equal to EOT	C + 1	-	0	-
0	1	Less than EOT	-	-	R + 1	-
0	1	Equal to EOT	C + 1	-	0	-
1	0	Less than EOT	-	-	R + 1	-
1	0	Equal to EOT	-	LSB	0	-
1	1	Less than EOT	-	-	R + 1	-
1	1	Equal to EOT	C + 1	LSB	0	-

• An empty cell means it is the same value as the one at the beginning of command execution
• LSB (Least Significant Bit): The least significant bit of H is complemented

Motor On/Off Flipflop

Writing 00h to Port &FA7E turns all disk drive motors off, writing 01h turns all motors on. It is not possible to turn on/off the motor of a specific drive separately.

An exception are the Vortex F1-S, F1-D, M1-S and M1-D drives. (How are they different?)

The floppy disc rotates at a nominal speed of 300rpm, with some tolerance.

Unconnected Pins

At the end of a successful read or write command, the program should send a Terminal Count (TC) signal to the FDC. However, in the CPC the TC pin isn't connected to the I/O bus, making it impossible for the program to confirm a correct operation. For that reason, the FDC will assume that the command has failed, and it'll return both Bit 6 in Status Register 0 and Bit 7 in Status Register 1 set. The program should ignore this error message.

The CPC doesn't support floppy DMA transfers, and the FDC's Interrupt signal isn't used in the CPC.

In the CPC, the US1 pin of the FDC is not connected, making it impossible to select floppy drives 2 and 3. The floppy drives 0 and 1 are selected instead.

Ready / Disk Changed signal

This signal differs between floppy drives model:

• For 3inch floppy drives (pin26), it is a "Ready" signal. The /RDY signal is active whenever a disk is installed and rotating in the drive.

• For 3.5inch floppy drives (pin34), it is a "Disk Changed" signal. The /DSKCHG signal determines whether the same disk loaded during the previous disk access is still in the drive.

The simplest solution to this issue is to just force the Ready signal on the cable itself. Note that the CPC will then hang if you type the CAT command when no disk is present (inserting a disk will unblock it).

Other solutions exist to Modify PC floppy drives to recreate a Ready signal. Also, Gotek drives (with a FlashFloppy or HxC firmware) can be configured to simulate the Ready signal.

Notes

Before accessing a disk you should issue a recalibrate command to the drive to move the head backwards until the track zero signal from the drive is sensed by the FDC. The FDC will also set its track counter for that drive to zero.

On an 80-track drive you may need to repeat that twice because some models of the FDC stop after 77 steps so if recalibrating from track 78 or above the controller might not reach track zero.

In order to format, read or write a sector on a specific track you must first seek that track using command 0Fh. That'll move the read/write head to the physical track number. If you don't do that then the FDC will attempt to read/write data from/to the current physical track, irrespective of the specified logical track ID.

The track, sector, and head IDs are logical IDs only. These logical IDs are defined when formatting the disk and aren't required to reflect the physical track, sector, or head numbers. However, when reading or writing a sector you must specify the same IDs that have been used during formatting.

Despite the name, a sector with a Deleted data Address Mark (DAM) is not deleted; the DAM-flag is just another ID bit. 'Deleted' sectors can be read/written just like normal data sectors and if that ID bit is specified correctly in the command.

Usually single sided 40-track 3" disk drives are used in CPCs. For practical purposes, 42 tracks could be used — the limit is specific to the drive and some support more tracks but 42 is a good maximum. The FDC controller can be used to control 80-tracks and/or double sided drives, though AMSDOS doesn't support such formats. AMSDOS supports a maximum of two disk drives only.

Floppy disk format specification

There are 4 standard formats on CPC, with the following characteristics:

	DATA	VENDOR or SYSTEM	IBM
Sector size	N=2 (512 bytes)
Number of sectors	9		8
Sector names	&C1 to &C9	&41 to &49	&01 to &08
Formatting byte	&E5
Starting track	00
Ending track	39
Catalog position	Track 0: sectors &C1 to &C4	Track 2: sectors &41 to &44	Track 1: sectors &01 to &04
Catalog size	2 KB
Catalog entries	64 max
Size per side	178 KB	169 KB	154 KB
Diskette size	356 KB	338 KB	308 KB

The SYSTEM format is a VENDOR format with the addition of information to BOOT the CP/M on:

• Track 0: sectors &41, &42, &48, &49
• Track 1: sectors &41, &46, &42, &47, &43, &48, &44, &49, &45

Type |CPM and you will find yourself under CP/M 2.2.

By the way, all the |CPM command does is load the 512 bytes of track 0 sector &41 into memory at address &100 and then execute it.

Directory record structure

It can support up to 64 entries of 32 bytes.

Byte Offset	Description	Comment
0	User Number	USER goes from 0 to 255. USER 229 (&E5) is for deleted files. RSX only gives access to USER 0 to 15.
1-8	Filename (excluding full stop)	Always in CAPS and maximum 8 characters long.
9-11	Extension	Always in CAPS and maximum 3 characters long. Read Only flag on byte9 bit7. Hidden flag on byte10 bit7. Archive flag on byte11 bit7.
12	Current Extent	0 is first extent.
13	Reserved
14	Extent High Byte	Not used.
15	Record Count (Number of 128 Byte Blocks)	Goes up to 128 (&80).
16–31	Cluster ID where to find the file data	1 byte is used per 1KB bloc.

Note: a file >16KB will require multiple entries in this table.

FDC Track Format

The CRC is initialised to FFFF. It is updated byte by byte and uses the CCITT-CRC16 algorithm. It is written after the ID and data fields of each sector in big-endian format (high byte first and then low byte).

Internal details of the chip

• The decapped photos of Intel 8271, NEC D765 and Intel 8272 chips prove that NEC D765 and Intel 8272 chips are identical.

• From a comment in the hackaday website: "Internally this is a microcoded part with a primative controller of NEC’s own design. Testing microcode embedded in a part can be troublesome. The uPD765 had a few extra gates associated with the DMA Request and DMA Ack pins. Presenting a certain illegal combination here places the part into a “test” mode and allows the sequencer microcode to be output on the normal Data pins. The sequencer microcode is responsible for high level commands such as Read Track, Recalibrate, Format Track, or Write Data. There is a similar test mode for the nano-code array which serializes data at the floppy disk head."

FDC Block Diagram

Generic System Diagram

The Amstrad CPC and Amstrad Plus do not have a DMA controller associated with the FDC. The INT pin of the FDC is not connected either.

PC to CPC floppy connector

FDD Block Diagram

Datasheets

• NEC uPD765 Datasheet preliminary (1979) Media:D765 NEC.pdf Media:UPD765-NEC.pdf Media:Z765A datasheet.pdf - uPD765 disc controller
• Media:Intel 8272A Datasheet preliminary (1982).pdf Intel 8272A Datasheet (1986) - Licensed clone of the uPD765
• Media:FDC9229BT Datasheet.pdf Media:SED9420.pdf - Data separators
• Media:DDI Schematic.png - DDI-1 Schematic (disc interface for CPC464)
• Media:Panasonic-3 inch Floppy Drive EME-150.pdf Media:NEC_FD1035_Floppy.pdf - Floppy disk drives
• Media:Floppy User Guide.pdf - Floppy User Guide

External links

• Quasar FDC documentation (in french)
• FDC blog articles (in french)
• Floppy disk formats (in french)
• Atari ST Floppy Drive hardware analysis
• MSX low-level disk storage article