Difference between revisions of "Schneiderware"

Revision as of 19:18, 20 September 2010

The Schneiderware series consists of several DIY projects which have been released in german magazine CPC Schneider International published by DMV. The name "Schneiderware" was probably choosen due to its double meaning ("CPC Hardware" in computer language, or "specially fitted clothing" in german language). Aside from building the hardware on one's own, one could also order printed circuit boards, either fully assembled, or in kit form.

The various boards are having special connectors, intended to be mounted on the "Basisplatine" (some kind of a motherboard) which allows to connect up to five Schneiderware boards to the CPCs Expansion Port; with some small modifications one could also connect the boards directly to the Expansion Port (the motherboard is merely an Y-cable-like adaptor without electrical components, so one doesn't really need it).

The DIY projects can be reportedly found in following issues (as by now, the magazine pages don't seem to be scanned, so details about I/O ports are unknown):

• CPC Schneider International 06/1986, Page 062-067, Schneiderware #1 Introduction (Theory)
• CPC Schneider International 07/1986, Page 060-067, Schneiderware #2 Basisplatine (Motherboard) & Centronics (Printer Port)
• CPC Schneider International 08/1986, Page 070-077, Schneiderware #3 V/24 (RS232 Interface)
• CPC Schneider International 09/1986, Page 078-083, Schneiderware #4 Netzteil (Power Supply)
• CPC Schneider International 10/1986, Page 078-085, Schneiderware #5 Echtzeituhr (Real Time Clock)
• CPC Schneider International 12/1986, Page 124-130, Schneiderware #6 Uni-PIO (48 I/O lines)
• CPC Schneider International 01/1987, Page 144, Notes (?)
• CPC Schneider International 03/1987, Page 032-045, Schneiderware #7
• CPC Schneider International 04/1987, Page 026-034, Schneiderware #8
• CPC Schneider International 05/1987, Page 032-034, Notes (?)
• CPC Schneider International 06/1987, Page 122-131, Schneiderware #9
• CPC Schneider International 11/1987, Page 097-099, Notes (?)

Notes: The "Centronics" board is yet another 8bit Printer Port solution (but different than the joystick-signal based one that was released a few months earlier in the same magazine). The Real Time Clock is somewhat similar to the CPCI Real Time Clock released in a special issue of the same magazine, but not identical (the RTC chip has different pin-outs, and some of it's 4bit registers are working slightly different, the leap-year bits, for example).

Pictures

• 

  Schneiderware #2
  Basisplatine (component side)

• 

  Schneiderware #2
  Basisplatine (solder side)

• 

  Schneiderware #2
  Centronics (component side)

• 

  Schneiderware #2
  Centronics (solder side)

• 

  Schneiderware #3
  V24 (component side)

• 

  Schneiderware #3
  V24 (solder side)

• 

  Schneiderware #4
  Supply/Netzteil (component side) (incomplete?)

• 

  Schneiderware #4
  Supply/Netzteil (solder side)

• 

  Schneiderware #5
  RTC/Echtzeituhr (component side)

• 

  Schneiderware #5
  RTC/Echtzeituhr (solder side)

• 

  Schneiderware #6
  Uni-PIO (component side)

• 

  Schneiderware #6
  Uni-PIO (solder side)

Datasheets

• M5832 Datasheet - Real time clock