Difference between revisions of "Schneiderware Real Time Clock"
(Created page with "The Schneiderware Real Time Clock is a battery-backed RTC, published by german magazine CPC Schneider International as part of their Schneiderware DIY series. The pla...") |
|||
| Line 2: | Line 2: | ||
The [[ECB Bus]] connector of the board is intended to be plugged into the [[Schneiderware Basisplatine]], but it could be also wired directly to the CPCs Expansion Port. | The [[ECB Bus]] connector of the board is intended to be plugged into the [[Schneiderware Basisplatine]], but it could be also wired directly to the CPCs Expansion Port. | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
== I/O Ports == | == I/O Ports == | ||
| Line 21: | Line 15: | ||
|- | |- | ||
|} | |} | ||
| + | |||
| + | '''Note''' - The Schneiderware Real Time Clock is somewhat similar to the [[Real Time Clock|CPCI Real Time Clock]] released in a special issue of the same magazine, but not identical (the RTC chip has different pin-outs, and some of it's 4bit registers are working slightly different, the leap-year bits, for example). | ||
| + | The I/O ports are also slightly different: The Schneiderware version has additional control bits in port FBE2h, and, for whatever reason, it splits data to two separate addresses (for FBE3h for writing, and FBE4h for reading), rather than mapping both to FBE3h. | ||
| + | |||
| + | == Software == | ||
| + | |||
| + | '''Caution''' - The listing in the magazine (and the databox files) are bugged and won't work: The I/O addresses are wrong. Additionally, some function entrypoints seem to be accidently set to 0000h. | ||
| + | |||
| + | Databoxes: '''UHR8000''' RTC-RAM-driver in 10-1986 (hex listing, plus [[Hisoft Devpac]] source code) (caution this version uses incorrect I/O addresses FBE1-FBE3), '''UHRC000X''' RTC-ROM-driver in 4-1987 (this version uses correct I/O addresses FBE2-FBE4). | ||
== Pictures == | == Pictures == | ||
Revision as of 11:35, 30 September 2010
The Schneiderware Real Time Clock is a battery-backed RTC, published by german magazine CPC Schneider International as part of their Schneiderware DIY series. The plain PCB, or the fully assembled board were also available via mail-order.
The ECB Bus connector of the board is intended to be plugged into the Schneiderware Basisplatine, but it could be also wired directly to the CPCs Expansion Port.
Contents
I/O Ports
| Address (default) | Address (alternate) | Usage |
| FBE2h | BUGGED:FBE1h | Schneiderware RTC index/control (W) |
| FBE3h | BUGGED:FBE2h | Schneiderware RTC data 4bit (W) |
| FBE4h | BUGGED:FBE3h | Schneiderware RTC data 4bit (R) |
Note - The Schneiderware Real Time Clock is somewhat similar to the CPCI Real Time Clock released in a special issue of the same magazine, but not identical (the RTC chip has different pin-outs, and some of it's 4bit registers are working slightly different, the leap-year bits, for example). The I/O ports are also slightly different: The Schneiderware version has additional control bits in port FBE2h, and, for whatever reason, it splits data to two separate addresses (for FBE3h for writing, and FBE4h for reading), rather than mapping both to FBE3h.
Software
Caution - The listing in the magazine (and the databox files) are bugged and won't work: The I/O addresses are wrong. Additionally, some function entrypoints seem to be accidently set to 0000h.
Databoxes: UHR8000 RTC-RAM-driver in 10-1986 (hex listing, plus Hisoft Devpac source code) (caution this version uses incorrect I/O addresses FBE1-FBE3), UHRC000X RTC-ROM-driver in 4-1987 (this version uses correct I/O addresses FBE2-FBE4).
Pictures
RTC Schematic
RTC/Echtzeituhr (component side)
RTC/Echtzeituhr (solder side)
.jpg)
.jpg)
Article
- Schneiderware #5 Echtzeituhr (Real Time Clock) (10/1986 pages 78-85, corrections on 12/1986 page 6 and 3/1987 page 9, 9/1987 page 9,
Datasheets
- M5832 Datasheet - Real time clock
